• Food Science and Preservation
• /
• v.12 no.4
• /
• pp.323-328
• /
• 2005

This study were investigated to analyzed an optimum preparation condition of coating film and its antimicrobial activity on pathogenic and deteriorative bacteria to obtain fundamental data for development of active packaging film using antimicrobial peptide, polysine. In the preparation conditions of coating film, antimicrobial activity was depending on the concentration of polylysine and polyamide respectively, and relatively high activity was obtained in the film prepared with more than $1.0\%$ (w/v) of polylysine, $40\%$ (w/v) polyamide, and more than $50\;{\mu}m$ of film thickness. Concentration of polylysine migrated from coated film to distilled water was reached at the maximum concentration, about 20 ppm after 3 days and in equilibrium after 7 days of soaking in sterilized water. An antimicrobial activity of coated film showed bactericidal effect of about $10^5\;CFU/mL$ comparing with the control against Bacillus cereus having $4.8{\times}10^5\;CFU/mL$ of initial viable cell numbers, and of about $10^2\;CFU/mL$ comparing with the control against Klebsiella pneumoniae having $6.8{\times}10^5\;CFU/mL$ of initial viable cell numbers. Consequently, it was revealed that polylysine coating film has a potential of applicable possibility as antimicrobial packaging film.

• Journal of the Korean Society for Precision Engineering
• /
• v.33 no.3
• /
• pp.231-234
• /
• 2016

Pouch film is manufactured by laminating aluminum foil, polyamide film and polypropylene film with an adhesive or extrusion resin. However, a surface treatment is required for the aluminum because bonding does not occur easily between the aluminum foil and the polymer film. Thus, for this study, surface treatment experiments were performed in order to confirm the effect on adhesion strength. First, a variety of surface treatment solutions were coated on aluminum foil, and contact angle and surface morphology analysis was carried out for the surface-treated aluminum. For lamination of the surface-treated aluminum foil with polyamide film, a polyurethane base adhesive was prepared for the adhesive strength test specimens. The adhesive strength between the aluminum foil and the polyamide film of the resulting specimens was measured (UTM). With such an experiment, it was possible to evaluate the effect on adhesive strength of the various surface treatments.

• Journal of the Korea Institute of Building Construction
• /
• v.17 no.5
• /
• pp.437-444
• /
• 2017

In the composite waterproofing method in which a polyurethane coating waterproofing material is applied on the modified asphalt waterproofing sheet, the organic solvent is diluted in the coating waterproofing material in order to improve the workability. However, since the organic solvent is not volatilized before the curing of the polyurethane coating waterproofing material, the organic solvent causes dissolution of asphalt layer, thereby causing oil leakage. As a result, a polyamide film having a high dissolution resistance property was laminated on modified asphalt sheet, and through testing the dissolution resistance was visually confirmed and quantitative analysis of the polyamide film by SEM-EDX analysis was also used to confirmed the dissolution resistance of the polyamide film.

• Journal of the Korean Applied Science and Technology
• /
• v.25 no.2
• /
• pp.144-150
• /
• 2008

The polyamide-amide-imide (PAAI) was synthesized by reacting 4,4'-diaminobenzanilide (DBA) with trimellitic anhydride chloride using a two-stage heating. The precursor of polyamide-acids was formed at first stage and followed by the formation of imide of PAAI. Two polyamide-imides (PAIs) were prepared from benzidine (BZ) or 4,4'-diaminodiphenylether (DPE) with trimellitic anhydride chloride. These three polymers had glass transition temperature in the temperature range of $240-250^{\circ}C$. X-ray data were obtained on thin film specimens cured at $250^{\circ}C$. There was a minimal kind of short-range order consisting of the most probable distances between neighboring chains. The average segmental spacing of short-range order decreased in the order of polymers obtained from 4,4'-diaminobenzanilide (DBA), polyamide-imide, and 4,4'-diaminodiphenylether (DPE). The imidization of three polyamide-imides was confirmed by $^{15}N$ MAS NMR and FT-IR spectroscopy. $^{15}N$ NMR spectrum of cured polyamide-imide showed imide $^{15}N$ peak, thereby providing an evidence for the imidization of three polyamide-imides.

• Proceedings of the Korean Fiber Society Conference
• /
• 1995.10a
• /
• pp.107-107
• /
• 1995

• Applied Chemistry for Engineering
• /
• v.8 no.2
• /
• pp.276-285
• /
• 1997

The theoretical and experimental analysis on polyamide used for reverse osmosis thin-film composite membrane had been conducted. The physicochemical properties of polyamide had been varied by preparation recipes which depends on kinds of monomer, solvents and polymerization time. These properties and performance as a reverse osmosis membrane had been calculated by group contribution method. The experimental results has the same trends with theoretical preview.

• Membrane and Water Treatment
• /
• v.10 no.6
• /
• pp.451-460
• /
• 2019

Thin film composite membranes incorporated with nano-sized hydrophilic zeolite -A were successfully prepared via interfacial polymerization (IP) on porous blend PES/PAN support for water desalination. The thin film nanocomposite membranes were characterized by SEM, contact angle and performance test with 7000 ppm NaCl solution at 7bar. The results showed that the optimum zeolite loading amount was determined to be 0.1wt% with permeate flux 29LMH.NaCl rejection was improved from 69% to 92% compared to the pristine polyamide membrane where the modified PA surface was more selective than that of the pristine PA. In addition, there was no significant change in the permeate flux of the thin film nanocomposite membrane compared with that of the pristine PA in spite of the formation of the dense polyamide layer. The stability of the polyamide layer was investigated for 15 days and the optimized membrane presented the highest durability and stability.

• Membrane Journal
• /
• v.26 no.4
• /
• pp.281-290
• /
• 2016

Thin film composite (TFC) polyamide membranes were prepared on polysulfone (PSF) supports for forward osmosis (FO) applications. To understand the influence of polarity and porosity of support layer on the formation of polyamide structure and the final FO performance, clathochelate metal complex (MC) contained PSF supports were prepared via the phase inversion process from various PSF casting solutions containing 0.1-0.5 wt% of MC in dimethyl formamide (DMF) solvent (18 wt%). A crosslinked aromatic polyamide layer was then fabricated on top of each support to form a TFC membrane. For the porous PSF supports prepared with relatively low concentration casting solutions (12 wt%), the PET film was removed after phase inversion and crosslinked aromatic polyamide layer was then fabricated. The tested sample from PSF (18 wt%)/MC (0.5 wt%) casting solution presented outstanding FO performance, almost similar water flux (9.99 LMH) with lower reverse salt flux (RSF, 0.77 GMH) compared to commercial HTI FO membrane(10.97 LMH of flux and 2.2 GMH of RSF). By addition of MC in casting solution, the thickness of the active layer in FO membranes was reduced, however, the increased RSF value was obtained.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.7
• /
• pp.4457-4462
• /
• 2014

This paper presents an antenna design that can be applied to flexible transparent conducting film. The antennas shaping PIFA (Planar Inverted F-shpae Antenna) were produced on polyamide substrates, which are flexible. The IZTO/Ag/IZTO multilayer films were used for the antennas and exhibited superior electrical, optical and flexible characteristics. This study compared the transparency and performance of two antennas (IZTO/Ag/IZTO multilayer film, and Ag monolayer film). The operation frequencies were set to 5.18~5.32 GHz of WLAN (802.11a). The performance showed a maximum efficiency and peak gain of 89 % and 5.86 dBi, respectively.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.419-419
• /
• 2012

We fabricated the Polyamide 4,6 (PA46) thin film using Adipoyl chloride and 1,4-butadiamine. PA46 film was grown at $70^{\circ}C$ by Molecular Layer Deposition (MLD) method. MLD is sequential and self-terminating fabrication method for organic thin film. The growth rate of PA46 is $3.5{\acute{\AA}}$ cycle. The thickness of PA46 film was measured by Ellipsometer. Surface morphology of this film was investigated by Atomic Force Microscopy (AFM) and roughness is directly proportional to number of growing cycles.