• Proceedings of the KIEE Conference
• /
• 2001.07c
• /
• pp.1457-1459
• /
• 2001

This paper deals with the change of surface Potential decay, surface resistivity, contact an91e and XPS of ultraviolet-treated PET films. From the experimental results on the surface Potential decay of UV degraded-samples, it was found that the accumulation of charge is decreased and the surface potential decay time is shortened. Also, from the result of XPS, it was found that the changes affected by the surface degradation of PET film were caused by the generation of carboxyl groups through the chain decomposition and recombination with oxygen molecules in the air.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.275-275
• /
• 2008

This paper describe the fabrication of a Pd/polycrystalline 3C-SiC schottky diode and its characteristics, in which the polycrystalline 3C-SiC layer and Pd Schottky contact were deposited by using APCVD and sputter, respectively. Crystalline quality, uniformity, and preferred orientations of the Pd thin film were evaluated by SEM and XRD, respectively. Pd/poly 3C-SiC Schottky diodes were fabricated and characterized by I-V and C-V measurements. Its electric current density Js and barrier height voltage were measured as $2\times10^{-3}$ A/$cm^2$ and 0.58 eV, respectively. These devices were operated until about $400^{\circ}C$. Therefore, from these results, Pd/poly 3C-SiC Schottky devices have very high potential for high temperature chemical sensor applications.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.481-482
• /
• 2008

In this paper, the advanced process has been presented to remove the WSix peeling that was made in sub 100nm DRAM SRCAT(Sphere-shaped-Recess-Ch annel-Array Transistor). The source of WSix peeling was proved to be the groove of gate poly film. We have completely solved the problems to adopt the gate-poly CMP (Chemical Mechanical Polishing) process.

• Proceedings of the IEEK Conference
• /
• 2002.06b
• /
• pp.193-196
• /
• 2002

This paper presents the improvement of the boron penetration and the reverse short channel effect (RSCE) in the 130nm W/WNx/Poly-Si dual gate PMOSFET for a high performance embedded DRAM. In order to suppress the boron penetration, we studied a range in the process heat budget. It has shown that the process heat budget reduction results in suppression of the boron penetration. To suppress the RSCE, we experimented with the halo (large tilt implantation of the same type of impurities as those in the device well) implant condition near the source/drain. It has shown that the low angle of the halo implant results in the suppression of the RSCE. The experiment was supported from two-dimensional(2-D) simulation, TSUPREM4 and MEDICI.

• Proceedings of the IEEK Conference
• /
• 2000.11b
• /
• pp.208-211
• /
• 2000

This paper describes the design of a CMOS frequency synthesizer using programmable frequency divider with novel architecture. A novel architecture of programmable divider can be producted all of integer-N and fabricated by 0.65$\mu\textrm{m}$ 2-poly, 2-metal CMOS technology. Frequency synthesizer is simulated by 0.25$\mu\textrm{m}$ 2-poly, 5-metal CMOS technology. This circuit has settling time of 1.5${\mu}\textrm{s}$ and power consumption of 70㎽. Operating frequency of the frequency synthesizer is 820MHz∼l㎓ with a 2.5V supply voltage.

• Proceedings of the IEEK Conference
• /
• 2003.07b
• /
• pp.667-670
• /
• 2003

Ni-silicide has low thermal stabiliy. This point is obstacle to apply NiSi to devices. So In this paper, we have studied for obtain thermal stability and analysis of dopant dependency of NiSi. And then we applied Ni-silicide to devices. To improvement of thermal stability, we deposit Ni70/Co10/Ni30/TiN100 to sample. Co midlayer is enhanced thermal stability of NiSi. Co/Ni/TiN, this structure show very difference between n-poly and p-poly in sheet resistance. But Ni/Co/Ni/TiN, structure show less difference. Also junction leakage is good.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2005.11a
• /
• pp.87-90
• /
• 2005

This paper presents an evaluation of the effect of titanium dioxide nanoparticles in sulfonated poly(ether ether ketone) (SPEEK) with sulfonation degree of 57%. A series of inorganic-organic hybrid membranes were prepared with a systematic variation of titanium dioxide nanoparticles content. Their water uptake, methanol permeability and proton conductivity as a function of temperature were investigated. The results obtained show that the inorganic oxide network decreases the proton conductivity and water swelling. It is also found that increase in inorganic oxide content leads to decrease of methanol permeability. In terms of morphology, membranes are homogeneous and exhibit a good adhesion between inorganic domains and the polymer matrix. The properties of the composite membranes are compared with standard nafion membrane.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1398-1401
• /
• 2003

Recently, The PolyPropylene(PP) Foam used as Bumper and Helmet is well known as a protective material for products. In this paper, the effect of the density of PP foams on the absorption of the impact energy is implemented. The result of the experiment has revealed that the effect of the high-density PP foams is remarkably increased compared with that of the low-density PP foams. And it also shows that the absorption of the impact energy of PP foams are greatly influenced by the density in impact velocity(220cm/s). These results are expected to be utilized for the technique of manufacturing a optimum impact structure.

• Journal of KSNVE
• /
• v.8 no.4
• /
• pp.690-699
• /
• 1998

This paper discusses the techniques, procedures and the results of the ground vibration test(GVT) performed on the development aircraft and the simple procedure of FE model updating technique from the GVT results. The GVT was carried out using random excitation technique with MIMO(Multi-Input-Multi-Output) data acquistion method, and taking full advantage of poly-reference global parameter estimation technique to identify the vibration modes. In dynamic FE modeling, the aircraft was represented by beam elements and all dynamic analysis was performed using MSC/NASTRAN for this model. In updating procedure, the stiffness of the beam model was adjusted iteratively so as to get the natural frequencies and mode shapes close to the GVT results.

• Advances in concrete construction
• /
• v.9 no.5
• /
• pp.479-489
• /
• 2020

Studies have proved that the mechanical properties of concrete, suddenly is dropped off with employing waste materials as replacements. The effectiveness of fibre addition on the structural stability of concrete has been indicated in recent investigations. There are different waste aggregates and fibres as plastic, rubber tire, coconut, and other natural wastes, which have been evaluated throughout the last decades. The fibres incorporation has a substantial effect on the properties of concrete mix subjected to different loading scenarios. This paper has reviewed different types of wastes and the effect of typical fibres including Poly Ethylene Terephthalate (PET), rubber tire, and waste glass. Furthermore, waste plastic and waste rubber has been especially studied in this review. Although concretes containing PET fibre revealed a reduction in compressive strength at low fibre fractions, using PET is resulted to micro-cracking decrement and increasing flexibility and flexural strength. Finally, according to the reviews, the conventional waste fibres are well-suited to mitigated time-induced damages of concrete and waste fibres and aggregates could be a reliable replacement for concrete.