• Journal of the Korean Electrochemical Society
• /
• v.18 no.3
• /
• pp.115-120
• /
• 2015

The mechanical and electrochemical properties of poly(ethylene oxide) (PEO)-coated Rayon separator were characterized using potassium polyacrylate (PAAK)-KOH electrolyte. The supercapacitive properties of activated carbon supercapacitor adopting the Rayon/PEO separator and PAAK-KOH electrolyte was also tested. As the PEO content increased, the mechanical strength increased. Room-temperature ionic conductivity of over $10^{-2}S\;cm^{-1}$ was obtained at the PEO content lower than 5 wt.%, applicable to a supercapacitor. As a result, the specific capacitance at $1000mV\;s^{-1}$ of the activated carbon supercapacitor adopting the Rayon/PEO separator and PAAK-KOH electrolyte was highly stable after 1000th cycle. This was due to high rate-capability provided by the fact that PEO coating could fix the entanglements among fiber filaments of Rayon.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1994.11a
• /
• pp.82-85
• /
• 1994

The purpose of this study is to research and develop solid polymer electrolyte(SPE) for Li secondary battery. This paper describes effects of plasticizer addition and temperature dependence of conductivity of these PEO electrolytes. Adding propylene carbonate and ethylene carbonate to PEO-LiClO$_4$electrolyte, its conductivity was higher than PEO-LiClO$_4$ itself. Steady state current method and AC impedance used for the determination of transference number in PEO electrolyte film. The transference number of PEO$\_$8/LiClO$_4$PC$\_$5/EC$\_$5/ polymer electrolyte film is 0.45 at 60$^{\circ}C$.

• Journal of Pharmaceutical Investigation
• /
• v.30 no.3
• /
• pp.207-211
• /
• 2000

The objective of this work is to investigate the effect of molecular weight of poly(ethylene oxide) (PEO) and release medium on the release of nifedipine (NP) from PEO tablets containing NP and to get some mechanistic insights into the release of NP. The tablets containing NP were prepared by direct compression, using a flat-faced punch and die. The molecular weights of PEOs used were 200K, 900K, 2000K and 7,000K. The release kinetics were studied for 24 hours in aqueous ethanol solution, using a dissolution tester at $36.5^{\circ}C$ and 100 rpm. Drug release rate increased, as the concentration of ethanol in the dissolution medium increased, due to the increased solubility of NP. As the molecular weight of PEO increased, release rate decreased, due to the slower swelling and dissolution of PEO. The power values obtained by fitting data to the power law expression $(M_t/M_{\infty}=kt^n)$ indicated that, at low ethanol concentration, the release of NP is governed by anomalous diffusion. However, as the ethanol concentration increases, diffusional release becomes to prevail over anomalous or zero-order release. Overall, these results provided some insights into the release of NP from PEO tablet.

• Bulletin of the Korean Chemical Society
• /
• v.10 no.2
• /
• pp.123-128
• /
• 1989

Calorimetric study in conjunction with Fourier-transform infrared (FTIR) spectroscopic study was carried out on the blends of poly(ethylene oxide) (PEO) with isotactic, atactic and syndiotactic poly(methyl methacrylate) (i-, a-, and s-PMMA). From the differential scanning calorimetric (DSC) measurements, the three types of blends show a depression of the melting temperatures. This indicates that PEO is compatible with i-, a-, and s-PMMA. But the largest melting point depressions of PEO are always found in the blends with s-PMMA. For PEO/a-PMMA and PEO/s-PMMA, the degree of crystallinity as a function of composition deviates substantially from that of the ideal blend in which no interaction between the components exists. The FTIR spectra of all three types of blends are recorded. In order to observe the microstructural changes of PEO in blends, we analyzed the spectra using digital weighted subtraction and addition techniques. It was concluded that the microstructures of PEO are strongly perturbed by the PMMA's. Among these blends PEO microstructure in PEO/s-PMMA blends is most greatly influenced. It indicates that the blending is most preferred with s-PMMA than a- and i-PMMA. It can be explained on the basis of the molecular structure of PMMA's.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1996.11a
• /
• pp.109-112
• /
• 1996

The purpose of this study is to research and develop solid polymer electrolyte(SPE) for all-stolid-state lithium battery. We investigated conductivity, electrochemical properites and impedence spectroscopy of poly(ethylene oxide)[PEO]/poly(vinylidene fluoride)[PVOF] blend electrolytes and charge/discharge cycling of LiCoO$_2$/SPE/Li cell. By adding PVDF and plasticizer to PEO-LICIO$_4$electrolyte, its condustivity was higher than that of PEO-LiCIO$_4$electrolyte. Also PEO$_4$PVDF$_4$LiClO$_4$PC$_{5}$EC$_{5}$ remains stable up to 4.4V vs Li/Li. The discharge capacity of the LiCoO$_2$composite cathode was 92mAh/g based on LiCoO$_2$.EX>.

• Polymer(Korea)
• /
• v.24 no.1
• /
• pp.29-37
• /
• 2000

Polyaniline (PANi)/Poly(ethylene of oxide) (PEO) in-situ blends were prepared by inducing phase separation through solvent evaporation after casting from solutions containing aniline monomer, oxidant (initiator), dopant and PEO in methanol/water mixed solvent. It was observed that the electrical conductivity first increases rapidly as PANi amount in the PANi/PEO blend increases and then slowly increases as the weight percentages of polyaniline become above 11 wt% in the blend. We also noted that the morphology of PANi/PEO blends changes when the holding time in a stirrer at constant temperature is varied and eventually affects the electrical conductivity. As the length of alkyl group in dopants increases, the electrical conductivity of doped blends increases. The PANi/PEO blend prepared with a high molecular weight of PEO yields higher electrical conductivity.

• Korean Chemical Engineering Research
• /
• v.47 no.4
• /
• pp.476-480
• /
• 2009

A polymer composite electrolyte of a blend of poly(methyl methacrylate)(PMMA) and poly(ethylene oxide) (PEO) as a host polymer, the ethylene carbonate as a solvent, and $LiClO_4$ as a salt was studied. The crystallinity of the polymer electrolytes was evaluated using differential scanning calorimeter(DSC). The ionic conductivity of the polymer electrolytes was measured by frequency response analyzer(FRA) method. The effect of PEO/PMMA blend ratios on the ionic conduction in these electrolytes was investigated. The electrolyte films showed a phase separation due to immiscibility of the PMMA with the PEO. The PMMA-rich phase and the PEO-rich phase were produced during a film casting. The ionic conductivity of blend electrolyte was dependent on the content of PMMA and showed the highest value at 20 wt.%. However, when PMMA content exceeds 20 wt.%, the ionic conductivity was decreased due to the slow ionic transport through the PMMA-rich phase.

• Applied Chemistry for Engineering
• /
• v.20 no.5
• /
• pp.527-531
• /
• 2009

Periodic mesoporous organosilicas (PMO) were synthesized using bis(triethoxy silyl) benzene as the precursor and dodecyl trimethyl ammonium bromide (DTMA) as the templating agent. From these results of XRD, TEM, and NMR, the pore structure of the material was confirmed to have a well-organized hexagonal structure. Poly(ethylene oxide) (PEO) was penetrated into PMO. From the DSC and XRD experiments, the polymer melting transition of crystalline polyethylene oxide (PEO) decreased then finally disappeared. These results prove that the polymer chains penetrate into the PMO channels, and penetrated polymer chains are constrained inside channels of PMO.

• Korea-Australia Rheology Journal
• /
• v.16 no.2
• /
• pp.57-62
• /
• 2004

Turbulent drag reduction (DR) efficiency of water soluble poly(ethylene oxide) (PEO) with two different molecular weights was studied as a function of polymer concentration and temperature in a turbulent flow produced via a rotating disk system. Its mechanical degradation behavior as a function of time in a turbulent flow was also analyzed using both a simple exponential decay function and a fractional exponential decay equation. The fractional exponential decay equation was found to fit the experimental data better than the simple exponential decay function. Its thermal degradation further exhibited that the susceptibility of PEO to degradation increases dramatically with increasing temperature.

• Proceedings of the Korean Fiber Society Conference
• /
• 2002.04a
• /
• pp.203-205
• /
• 2002

poly(ethylene oxide)(PEO)와 Poly(methyl methacrylate)(PMMA)는 상용성이 있는 고분자 블렌드계로서, 혼합되는 PMMA의 함량과 사용하는 용매 등에 의해서 PEO의 결정화 거동은 많은 영향을 받는다[l-3]. 비결정성 고분자인 PMMA의 함량이 증가할 수록 PEO의 결정 성장은 제약을 받게 되어 결정화 속도가 느려진다. 한편, PEO는 전기활성을 나타내는 고분자로서 외부전장을 가한 상태에서 용응 결정화시키면 전장의 영향을 받아 결정화가 늦어진다[4]. (중략)