• Polymer(Korea)
• /
• v.31 no.1
• /
• pp.8-13
• /
• 2007

To overcome drawbacks of the nylon 6/poly (acrylonitrile-co-butadiene-co-styrene) (ABS) blend, nylon 6 blend with poly (acrylonitrile - co-styrene - co-acrylic rubber) (ASA) which containing poly (butyl acrylate) as a rubber phase in substitute of poly (butadiene) in ABS, was examined. Poly (styrene-co-maleic anhydride) (SMA) containing 25 wt% of maleic anhydride (MA) or poly (styrene- co-acrylo-nitrile-co-maleic anhydride) (SANMA) containing less than 3 wt% MA was used as a compatibilizer to fabricate blends having high impact strength. Changes in the mechanical properties of nylon 6/ASA blend with compatibilizer content were similar with those of nylon 6/ABS blend. Blends haying high impact strength was produced when blends contained more than about 20 wt% rubber. Blends containing SAM or SANMA as a compatibilizer were stayed in a injection molding machine at the molding temperature and afterwards specimens for the examination of the impact strength was prepared. Impact strength of blends containing SMA was decreased with retention time, while that of blends containing SANMA was not changed with retention time.

• Elastomers and Composites
• /
• v.35 no.3
• /
• pp.188-195
• /
• 2000

The conducting composites were prepared by emulsion polymerization with poly (acrylonitrile-co-butadiene) (NBR) as a matrix and polypyrrole (PPY) as a conducting polymer. Among several surfactants, the electrical conductivity of the composite which was polymerized by dodecyl sodium sulfate (DSS) was the best. The film of composite was prepared by compression molding. The electrical conductivity was measured by 4 probes method as a function of PPY and temperature. When the content of PPY was 25 wt%, the electrical conductivity of composite was increased up to 1.17 S/cm. The percolation threshold showed at the vicinity of 15 wt% PPY content.

• Analytical Science and Technology
• /
• v.8 no.4
• /
• pp.603-610
• /
• 1995

The charge transfer rate in polypyrrole(PPy) electropolymerized within poly(acrylonitrile-co-butadiene)(PAB) was compared with that in PPy deposited Pt electrodes by using cyclic voltammetry, chronoamperometry, and chronopotentiometry in acetonitrile. For both electrodes anodic and cathodic peak currents were proportional to scan rates below 100 mV/sec, but to square root of scan rates beyond 200 mV/sec. The apparent diffusion coefficient of $ClO{_4}^-$ in the PPy/PAB composite is estimated to be 1.6 times larger than that in PPy. The PPy films composited within PAB layer showed higher anodic and cathodic currents and possessed faster charging-discharging process and larger capacity.

• Korean Chemical Engineering Research
• /
• v.49 no.4
• /
• pp.438-442
• /
• 2011

Mechanical and morphological properties of poly(acrylonitrile-butadiene-styrene) (ABS) and poly(lactic acid) (PLA) blends containing compatibilizers were investigated. Poly(styrene-acrylonitrile)-g-maleic anhydride) (SAN-g-MAH), poly(ethylene-co-octene) rubber-maleic anhydride (EOR-MAH) and poly(ethylene-co-glycidyl methacrylate) (EGMA) were used as compatibilizers. Mechanical properties such as tensile, flexural and impact strengths of ABS/PLA (80/20, wt%) blends were found to be increased when the SAN-g-MAH, EOR-MAH and EGMA were used. The maximum values for mechanical properties of the ABS/PLA (80/20) blend were observed when SAN-g-MAH was used as a compatibilizer at the concentration of 3 phr. From morphological studies of the ABS/PLA (80/20) blends, PLA droplet size was decreased by the addition of the compatibilizers used in this study. From the results of mechanical and morphological properties of the ABS/PLA (80/20) blends, SAN-g-MAH (3 phr) was found to be the most effective compatibilizer among the compatibilizers used in this study.

• Korean Membrane Journal
• /
• v.5 no.1
• /
• pp.36-42
• /
• 2003

A Prediction of pervaporation performance was studied by solubility parameter calculation approach for the benzene/cyclohexane mixture system using rubbery blend membrane with various solubility parameters. The solubility parameter of the rubbery blend membranes were controlled with different blend ratio of the poly(acrylonitrile-co-butadiene), poly(styrene-co-butadiene) and poly(vinyl chloride). Screening of blend formulations was accomplished by simple swelling tests. When the content of NBR is increased, the swelling of both benzene and cyclohexane are decreased. However, the ratio of benzene swelling to swelling by cyclohexane (the swelling selectivity) increases. The same is true for blends in which the PVC content is increased. Adoption of a solubility parameter calculation provides an a priori methodology for seeking the best blend formulation.

• Polymer(Korea)
• /
• v.26 no.1
• /
• pp.53-60
• /
• 2002

Polypropylene(PP : continuous phase)/poly (styrene-co-acrylonitrile)(SAN : dispersed phase) blends, and PP/poly(acrylonitrile-butadiene-styrene) (ABS : dispersed phase)blends, containing various amounts of compatibilizer(PP-SAN graft copolymer), were prepared at various shear rates by using twin-screw extruder. In the PP/SAN blend, the average size of the dispersed particles(SAN) was increased with SAN content, while the flexural strength and tensile strength were decreased with SAN content. When the screw rpm was increased from 10 to 60 rpm, the size of the dispersed phase was decreased while the flexural strength and the tensile strength were increased. Maximum mechanical strength and minimum droplet size were observed when the 5 phr compatibilizer was added to the PP/SAN blends. The mechanical strength of PP/ABS blends such as flexural strength and tensile strength increased by adding compatibilizer was reached maximum when blends contained 5 phr compatibilizer.

• Polymer(Korea)
• /
• v.38 no.1
• /
• pp.103-107
• /
• 2014

Poly(acrylonitrile-butadiene-styrene) (ABS) composite sheets containing titanium dioxide ($TiO_2$), barium sulfate ($BaSO_4$), calcium carbonate ($CaCO_3$) were prepared by using a co-rotating twin screw extruder, and the reflectance and flexural modulus of the composite sheets were measured. The fillers were well dispersed in ABS matrix. The reflectance of composite sheet was increased with increasing $TiO_2$ and $BaSO_4$ content. Sheet having $TiO_2$ 20 wt% composition, with 5~20 wt% $BaSO_4$ resulted in more than 95% of reflectance. The flexural modulus of composite sheet was increased from 1864 MPa for $ABS/TiO_2/BaSO_4$ 85/10/5 (w/w/w) to 3134 MPa for $ABS/TiO_2/BaSO_4$ 55/20/25 (w/w/w).

• The Korean Journal of Nuclear Medicine Technology
• /
• v.21 no.2
• /
• pp.65-73
• /
• 2017

Purpose 3D 프린팅 기술은 3D 스캔이나 모델링을 통하여 적측가공 방식으로 제작하는 기공기술로서 금형 없이 직접 생산이 가능하고 빠른 시간 내에 제작이 가능하여 최근 다양한 산업분야에서 본격적으로 적용되고 있다. 3D 프린팅 기술은 의료분야에 있어, 영상의학 및 방사선 치료분야에서 다양하게 활용되고 있지만 핵의학 분야에서는 관련 연구가 미비한 실정이다. 그러므로 본 연구는 기존에 적용되고 있는 핵의학분야 팬텀과 3D 프린팅 기술로 제작된 텀의 특성을 비교하고 적용 가능성을 평가하는데 목적을 두었다. Materials and Methods 방사선 투과도 변화측정 국제기준 팬텀인 알루미늄(Aluminum) 계단 쐐기(step wedge)를 기준($140mm{\times}62mm{\times}35mm$)으로 PMMA(Poly Methyl Meta Acrylate)와 ABS(Acrylonitrile Butadiene Styrene)재질로 각각 동일한 크기의 팬텀을 제작하였다. PMMA 팬텀은 핵의학 분야에서 주로 적용되는 팬텀의 성분과 동일한 소재로 제작하였고, ABS 팬텀 제작은 3D 프린팅 기술의 액체 기반형의 SLA(Stereo Lithography Apparatus)기법을 사용하여 제작하였다. 본 연구는 SPECT/CT장비 BrightView XCT(Philips Health Care, Cleveland, USA)를 이용하였다. 영상 획득은 Rectangular Flood phantom(Biodex, New York, USA) $^{99m}TcO_4$ 3, 6 mCi와 $^{57}Co$ lood phantom(adqual, New Hampshire, USA) $^{57}Co$ 20 mCi를 이용하여 Aluminum, PMMA, ABS 팬텀에 대해 60 min 리스트모드(List mode)로 획득하였다. 획득한 영상의 분석을 위해 관심영역(ROI)을 설정하여 각 팬텀의 단계별로 평가하였다. Results 방사선원의 종류 및 방사선량에 따라 ABS 팬텀의 계수치는 PMMA 팬텀의 계수치와 유사한 값을 나타내며, 두께의 증가에 따라 선형적으로 감소하였다. Aluminum, PMMA, ABS 팬텀의 선감약계수를 비교했을 때, Aluminum 팬텀의 선감약계수는 나머지 두 팬텀보다 수치가 높았고, PMMA, ABS 팬텀에서는 근사치의 선감약계수가 나타났다. Conclusion 3D 프린팅 기술로 제작된 ABS 팬텀을 기준으로 PMMA 팬텀은 두께가 증가함에 따른 계수치의 변화가 유사하게 선형적으로 감소하였고, 선감약계수도 근사치로 나타내었다. ABS 팬텀의 핵의학적 적용 가능성을 확인할 수 있었으며, 추후 연구를 통해 세부적인 교정치(correction value)를 적용한다면 활발한 적용이 가능하리라 사료된다.

• Journal of radiological science and technology
• /
• v.44 no.4
• /
• pp.343-350
• /
• 2021

3D printing technology is an additive manufacturing technology produced through 3D scanning or modeling method. This technology can be produced in a short time without mold, which has recently been applied in earnest in various fields. In the medical field, 3D printing technology is used in various fields of radiology and radiation therapy, but related research is insufficient in the field of nuclear medicine. In this study, we compare the characteristics of traditional nuclear medicine phantom with 3D printing technology and evaluate its applicability in clinical trials. We manufactured the same size phantom of poly methyl meta acrylate(PMMA) and acrylonitrile butadiene styrene(ABS) based on the aluminum step wedge. We used BrightView XCT(Philips Health Care, Cleveland, USA) SPECT/CT. We acquired 60 min list mode for Aluminum, PMMA and ABS phantoms using Rectangular Flood Phantom (Biodex, New York, USA) ^99mTcO₄ 3 mCi(111 MBq), 6 mCi (222MBq) and ⁵⁷Co Flood phantom(adq, New Hampshire, USA). For the analysis of acquired images, the region of interest(ROI) were drawn and evaluated step by step for each phantom. Depending on the type of radioisotope and radiation dose, the counts of the ABS phantom was similar to that of the PMMA phantom. And as the step thickness increased, the counts decreased linearly. When comparing the linear attenuation coefficient of Aluminum, PMMA and ABS phantom, the linear attenuation coefficient of the aluminium phantom was higher than that of the others, and the PMMA and ABS phantom had similar the linear attenuation coefficient. Based on ABS phantom manufactured by 3D printing technology, as the thickness of the PMMA phantom increased, the counts and linear attenuation coefficient decreased linearly. It has been confirmed that ABS phantom is applicable in the clinical field of nuclear medicine. If the calibration factor is applied through further research, it is believed that practical application will be possible.

• Elastomers and Composites
• /
• v.52 no.3
• /
• pp.187-193
• /
• 2017

In this study, the effect of the cure, mechanical properties, and oil resistance of NBR (acrylonitrile-butadiene rubber)/peroxide compounds were investigated for various co-agents. NBR compounds were characterized using a swelling test, a rheometer (MDR), and a compression set test. Mechanical properties were tested with original compounds, heated in air and exposed to the ASTM No.1, IRM 903 oil. NBR compounds were prepared using peroxide as the crosslinking agent. Trimethylolpropane trimethacrylate (TMPTMA), triallyl isocyanurate (TAIC), and 1,2-polybutadiene (HVPBD) were used as co-agents. The NBR compounds containing TMPTMA and HVPBD lowered the scorch time, while the addition of TAIC did not significantly change the scorch time. NBR compounds containing TMPTMA increased the crosslinking density, while the addition of TAIC and HVPBD lowered the crosslinking density. Moreover, the addition of TMPTMA improved the oil resistance of the NBR compound.