• 대한전기학회논문지:전력기술부문A
• /
• 제49권10호
• /
• pp.486-493
• /
• 2000

This paper presents an application to a multimachine power system of power system stabilizer using revised pole shift adaptive algorithm. Controller parameters are determined by using adaptive control theory in order to maintain optimal operation of generator under the various operating conditions. To determine the optimal parameters of controller and overcome the problem of pole placement algorithm, this paper presents pole shift algorithm revised pole shift factor. Also, the difference between the speed deviation with weighted factor and voltage deviation is used as the input signal of adaptive controller, which provides good damping characteristics. The results tested on a multimachine power system verify that the proposed controller has better dynamic and transient performance than conventional controller.

• 한국지구과학회지
• /
• 제37권5호
• /
• pp.271-276
• /
• 2016

We present our estimate of pole shift caused by the recent 31 largest earthquakes of magnitude over 8.0. After reviewing theory of perturbation in the Earth's rotation, each co-seismic as well as post-seismic pole shifts by the earthquakes are acquired and illustrated. A total co-seismic excitation due to these earthquakes is ($x_1$, $x_2$)=(-3.35, 5.89) milliarcsec, which increased about twice the initial estimation when the post-seismic deformation is considered. The single largest co-seismic excitation by 2011 Japan earthquake was ($x_1$, $x_2$)=(-2.06, 2.36) milliarcsec, which corresponds to 9.7 cm pole shift on the surface of the Earth.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1989년도 한국자동제어학술회의논문집; Seoul, Korea; 27-28 Oct. 1989
• /
• pp.194-199
• /
• 1989

In this paper, using the direct drive arm for plant, the controller is developed to track the desired trajectory in high speed and precision. For the purpose of this, through extending self-tuning pole-placement algorithm, we developed self-tuning pole-shift algorithm which is fast in response and good tracking for the reference tracking change. Developed controller is applied a three-link direct drive arm with the varing payload to track the desired tracking. And, through the computer simulation, the performance of developed controller is compared with the performance of the computed torque method and the self-tuning pole placement algorith.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1989년도 하계종합학술대회 논문집
• /
• pp.146-150
• /
• 1989

In the pole assignment strategy, the closed loop poles are placed at prespecified locations. The amount of control effort required is to some extent proportional to the distance of the proposed closed loop locations of the poles from their open loop locations. The poor choice of closed loop locations may result in Large control effort and it may nuke the system unstable. To overcome this problem, pole shift control strategy is described in this paper. The validity of the proposed control strategy is assured through some simulations.

• 전기저널
• /
• 10호통권118호
• /
• pp.58-61
• /
• 1986

• 전기저널
• /
• 12호통권120호
• /
• pp.47-51
• /
• 1986

• 전기저널
• /
• 11호통권119호
• /
• pp.68-72
• /
• 1986

• 전기저널
• /
• 9호통권117호
• /
• pp.56-61
• /
• 1986

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제49권11호
• /
• pp.627-634
• /
• 2000

In this paper, new micromachined tunble bandpass filters for multi-band millimeter-wave telecommunication systems are proposed. Two types of mm-wave tunable filters are fabricated using micromachning technology and the responses of the filters are measured. One is two-pole lumped elements filter and the other two-pole resonators filter. Frequency tunability of the filter is achieved by changing the gap between a common CPW ground plate and the movable cantilever beam connected to the transmission line with the controllable renge of 2.5${\mu}m$. The deflection of cantilever beam is measured with the applied DC voltage. With the applied bias voltage from 0 to 50 V, the fabricated filters show 0.6 GHz(2.3%) at 26.6 GHz, and 0.8 GHz(2.5%) at 32 GHz center frequency shift for the lumped elements and resonators filter, respectively. The life time of the fabricated gold cantilever structure are tested.

• 한국지능시스템학회논문지
• /
• 제16권5호
• /
• pp.627-634
• /
• 2006

CMOS 인버터 특성곡선의 기울기를 조절하는 방법과 y축으로 이동할 수 있는 방법을 제안하였다. 기울기의 변경과 y축으로 이동은 트랜지스터의 문턱 값을 조절하는 방법을 사용하였다. 그리고 특성곡선의 중심에서는 두 트랜지스터 모두 포화영역에 머물러 있음에 착안하여, 단극성 뉴런의 특성곡선을 만드는 방법을 제안하였다. 제안된 방법은 회로레벨의 시뮬레이션을 통해 검증하였으며, 회로레벨의 시뮬레이션은 OrCAD사의 PSpice(Professional Simulation Program with Integrated Circuit Emphasis)를 사용하였다.