• The Transactions of the Korean Institute of Power Electronics
• /
• v.13 no.5
• /
• pp.360-368
• /
• 2008

A lumped parameter model of Li-ion battery in hybrid electric vehicle(HEV) is constructed and system parameters are identified by using recursive least square estimation for different C-rates, SOCs and temperatures. The system characteristics of pole and zero in the frequency domain are analyzed with the parameters obtained from different conditions. The parameterized model of a Li-ion battery indicates highly dependent of temperatures. To estimate SOC and polarization voltage, a Luenberger state observer is utilized. The P- or PI-gains of observer based on a suitable natural frequency and damping ratio is adopted for the state estimation. Satisfactory estimation accuracy of output voltage and SOC is especially obtained by a PI-gain. The feasibility of the proposed estimation method is verified through experiment under the conditions of different C-rates, SOCs and temperatures.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.8
• /
• pp.1085-1091
• /
• 2014

A model based SOC estimation scheme using parameter identification is described and applied to a Lithium-ion battery module that can be installed in electric vehicles. Simulation studies are performed to verify the effect of sensor faults on the SOC estimation results for terminal voltage sensor and load current sensor. The sensor faults should be detected and isolated as soon as possible because the SOC estimation error due to any sensor fault seriously affects the overall performance of the BMS. A new fault detection and isolation(FDI) scheme by which the fault of terminal voltage sensor and load current sensor can be detected and isolated is proposed to improve the reliability of the BMS. The proposed FDI scheme utilizes the parameter estimation of an input-output model and two fuzzy predictors for residual generation; one for terminal voltage and the other for load current. Recently developed dual polarization(DP) model is taken to develope and evaluate the performance of the proposed FDI scheme. Simulation results show the practical feasibility of the proposed FDI scheme.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.763-766
• /
• 2000

In this paper, stator form-winding sample coils based on silicone resin and polyimide were made for fault prediction and reliability estimation on the 200 Class insulation system of traction motors. The complex accelerative degradation was performed by periods during 10 cycles, which was composed of thermal stress, fast rising surge voltage, vibration, water immersion and overvoltage applying. After aging of 10 cycles, condition diagnosis test such as insulation resistance & polarization index, capacitance & dielectric loss and partial discharge properties were investigated in the temperature range of 20∼160$^{\circ}C$. Relationship among condition diagnosis test was analyzed to find an dominative degradation factor and an insulation state at end-life point.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.28 no.12
• /
• pp.982-992
• /
• 2017

In this paper, we introduce a method of selection for the optimal transmission polarization of a W-band seeker through the extraction of the one-dimensional scattering center of a ground tank target. We calculated the surface scattering and edge scattering using the shooting and bouncing ray tracing method of the CST A-solver. Based on 4-channel RCS data, using the one-dimensional RELAX algorithm, which is a kind of spectral estimation technique, scattering centers of ground targets were extracted. According to the changes in the polarization state and look angle, we compared and analyzed the scattering center results. Through simulation, we verified that the scattering center results can be applied when feature vectors are used for target recognition.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.9
• /
• pp.707-721
• /
• 2018

In this paper, a small synthetic aperture radar(SAR) system with 30 cm resolution is proposed, and a RAW data-based Doppler parameter estimation and motion compensation algorithm is described in detail. Acquisition of both PolSAR and InSAR data are enabled because there are two channels each in the transmitter and receiver modules. Automotive-based field work is performed to obtain PolSAR data, and signal processing results are ultimately obtained. A motion compensation algorithm is used to mitigate the residual phase error due to platform oscillation, and improved performance is obtained with the motion compensation algorithm using the automotive field test data.

• Journal of the Korea Concrete Institute
• /
• v.17 no.2 s.86
• /
• pp.221-227
• /
• 2005

The presence of voids behind tunnel linings is very likely to result in settlement or structural collapse. One proposed method of detecting such voids by non-destructive method is radar. More than effectively judging the existence of voids behind tunnel linings, this study aims to develop the analysis algorithm of radar capable of estimation of the shape of specific voids. To acquire directional information and estimate the shape of three-dimensional voids, the radar of three-dipole antenna type is used. As a foundation to this ongoing research, an investigation of microwave polarization methods using three-dipole antenna carried out with various void orientations and void geometries. As a result, it is clarified that the response of four microwave polarization modes depends on void geometry and thus there is a possibility of identifying the geometry and orientation (the shape) of specific voids using radar of three-dipole antenna type.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.18 no.3
• /
• pp.61-69
• /
• 2018

In this paper, we propose a method for recognizing ground target using dual polarization channels in millimeter waveband air-to-surface radar. First, the Push-Broom target detection method is described and the received signal is modeled considering flight-path scenario of air-to-surface radar. The scattering centers were extracted using the RELAX algorithm, which is a time domain spectral estimation technique, and the feature vector of the target was generated. Based on this, a DB for 4 targets is constructed. As a result of the proposed method, it is confirmed that the target classification rates is improved by more than 15% than the single channel using the data of the dual polarization channel.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.6 no.5
• /
• pp.27-37
• /
• 1992

We studied the dielectric and dynamic mechanical losses according to the quenching condition in low density polyethylene being used to power cables. According to severe quenching condition, characteristics of the temperature in internal friction los peak have decreased the magnitude of loss peak as amorphous region lengthen. From now on, the frequency dependent characteristics of dielectric loss have investigated at room temperature, and the dielectric loss peak due to interface polarization, between crystal and amorphous region, occurs about 30[Hz], and that, the peak due to orientation polarization in correspondence to the loss peak in internal friction has observed at about 3 [MHz]. As quenching velocity increased, the effect on quenching condition about the dielectric loss has decreased the magnitude of the loss peak. Thus, estimation has been carried out on the activation energies nd the degree of crystallinity by means of X-ray diffraction are obtained as follows: room quenching : 26.4 [kal/mole] and 54.73 [%], ice quenching : 25.6 [kcal/mole] and 48.47 [%], liquid nitrogen quenching specimens : 22.56 [kcal/mole] and 40.95 [%].

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.10a
• /
• pp.15-20
• /
• 2000

In this paper. Thermally Stimulated Current spectra have been measured in the Polypy - romellitimide (polyimide). As a result of the investigation. three peaks have been observed: $A(50^{\circ}C)$, $B(120^{\circ}C)$, $C(200^{\circ}C)$. Among three peaks, C peak has been observed in detail. The C peak is shown to be created due to the polarization of ionic space charge from the experimental results which were measured as a function of forming time, forming temperature. forming voltage and collecting voltage. As a result, we have measured the TSC in ion ($Na^+$) implanted - Polyimide, also found the peak at $215^{\circ}C$. Therefore, TSC characteristics in the C peak is probably caused by residual impurity. And The activation energy caculated by means of initial rising method 1.8eV, hopping distance. $90{\AA}$. and the mobility. $2.88{\times}10^{-11}cm^2/v.s$

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.10a
• /
• pp.50-55
• /
• 2000

In this paper, Thermally Stimulated Current(TSC) spectrum has been measured in oriented polypropylene of thickness of $40{\mu}m$ which was irradiated by Ultraviolet Ray. As a result of the investigation, four peaks have been observed-two peaks ($A_1$, $A_2$) were appeared in low temperature region($-20{\sim}20^{\circ}C$) and other two peaks ($B_1$, $B_2$) in high temperature region($80{\sim}120^{\circ}C$). Among four peaks $A_1$ and $A_2$ have bee observed in detail. These peaks are shown to be created due to the polarization of diploes from the experimental results which were measured as a function forming voltage, forming time, collecting voltage and heating rate. As the increase of irradiated-time by Ultraviolet ray, the number of dipoles was increased.