• Explosives and Blasting
• /
• v.27 no.1
• /
• pp.32-37
• /
• 2009

To look over the effect of mixed proportion of cement, sand and water on strength, 162 tests were made for 9 mix proportions. It was observed that strength increased as water in the mixture is reduced. As a result of the control of sand ratio by 50%, the execution strength increased when the sand ratio is raised. Strength was consistent during curing period on each mix proportion, but there were sections where it suddenly increased. Poisson's ratio widely ranged from 0.13 to 0.27, and Young's modulus also broadly ranged from 13.79MPa to 33.25MPa. Poisson's ratio had nothing to do with uniaxial compressive strength, wheras Young's modulus was concerned with it. Young's modulus from theory and experiment showed similar outcome on the 3rd curing day, however, the strength from theory was higher than that from test after 3rd day. In consequence, there was a great change of strength between 3rd and 7th curing day. In addition, it is more efficient to use field strength value between the 3rd and 7th day and to apply Young's modulus on it for determining the exact time.

• Geomechanics and Engineering
• /
• v.24 no.1
• /
• pp.57-65
• /
• 2021

The effects of initial soil fabric and aspect ratio (AR) on the small-strain stiffness (G0) of granular soils are studied by employing discrete element method (DEM) numerical analysis. Elongated clumps composed of subspheres were adopted, and the G0 values were obtained by DEM simulations of drained triaxial tests under different densities and initial confining pressure (p0). The DEM simulations indicate that the initial soil fabric has an insignificant effect on G0. The effect of the AR on G0 is related to the initial density. Namely, for dense specimens, G0 first increases with increasing AR, reaching a plateau value when the AR ≥ 1.5. However, for loose specimens, G0 gradually increases as the AR increases. Microscopic examination reveals that G0 uniquely depends on the coordination number of the particles (CN-particle) rather than the subspheres (CN-sphere) at the particulate level for the effects of initial soil fabric and AR. Finally, Poisson's ratio ν0 is also determined by CN-particle. In addition, based on data in literature and this study, ν0 can be fitted as ν0 = 5.920(G0/(p0)1/3)-0.99, which can be used to predict ν0 of granular soils based on the measured G0.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.3
• /
• pp.579-584
• /
• 2012

In this paper, drain induced barrier lowering(DIBL) has been analyzed as one of short channel effects occurred in double gate(DG) MOSFET. The DIBL is very important short channel effects as phenomenon that barrier height becomes lower since drain voltage influences on potential barrier of source in short channel. The analytical potential distribution of Poisson equation, validated in previous papers, has been used to analyze DIBL. Since Gaussian function been used as carrier distribution for solving Poisson's equation to obtain analytical solution of potential distribution, we expect our results using this model agree with experimental results. The change of DIBL has been investigated for device parameters such as channel thickness, oxide thickness and channel doping concentration.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.7
• /
• pp.571-580
• /
• 1998

The numerical model that can describe the ignition of pseudospark discharge using hybrid fluid-particle(Monte Carlo )method has been developed. This model consists of the fluid expression for transport of electrons and ions and Poisson's equation in the electric field. The fluid equation determines the spatiotemporal dependence of charged particle densities and the ionization source term is computed using the Monte carlo method. This model has been used to study the evolution of a discharge in Argon at 0.5 torr, with an applied voltage if 1kV. The evolution process of the discharge has been divided into four phases along the potential distribution : (1) Townsend discharge, (2) plasma formation, (3) onset of hollow cathode effect, (4) plasma expansion. From the numerical results, the physical mechanisms that lead to the rapid rise in current associated with the onset of pseudospark could be identified.

• Fire Science and Engineering
• /
• v.26 no.4
• /
• pp.31-41
• /
• 2012

This study collected 5,100 cases of gas accident occurred in Korea for 14 years from 1995 to 2008, established Database and based on it, analyzed them by detailed forms and reasons. As the result of analyzing the whole city gas accidents with Poisson analysis, the item of "Careless work-Explosion-Pipeline' showed the highest rate of accidents for the next 5 years. And, "Joint Losening and corrosion-Release-Pipeline" showed the lowest rate of accident. In addition, for the result of analyzing only accidents related to LPG vaporizer, "LPG-Vaporizer-Fire" showed the highest rate of accident and "LPG-Vaporizer-Products Faults" showed the lowest rate of accident. Also, as the result of comparing and analyzing foreign LPG accident accompanied by Jet fire, facility's defect which is liquid outflow cut-off device and heat exchanger's defect were analyzed as the main reason causing jet fire, like the case of Korea, but the number of accidents for the next 5 years was the highest in "LPG-Mechanical-Jet fire" and "LPG-Mechanical-Vapor Cloud" showed the highest rate of accidents. By grafting Poisson distribution theory onto gas accident expecting program of the future, it's expected to suggest consistent standard and be used as the scale which can be used in actual field.

• Advances in nano research
• /
• v.17 no.2
• /
• pp.137-147
• /
• 2024

Graphene nanoribbons (GNRs) are considered a promising alternative to graphene for future nanoelectronic applications. However, GNRs-based device modeling is still at an early stage. This research models the electronic properties of n-doped rough-edged 13-armchair graphene nanoribbons (13-AGNRs) and quantum transport properties of n-doped rough-edged 13-armchair graphene nanoribbon field-effect transistors (13-AGNRFETs) at different doping concentrations. Step-up and edge doping are used to incorporate doping within the nanostructure. The numerical real-space nearest-neighbour tight-binding (NNTB) method constructs the Hamiltonian operator matrix, which computes electronic properties, including the sub-band structure and bandgap. Quantum transport properties are subsequently computed using the self-consistent solution of the two-dimensional Poisson and Schrödinger equations within the non-equilibrium Green's function method. The finite difference method solves the Poisson equation, while the successive over-relaxation method speeds up the convergence process. Performance metrics of the device are then computed. The results show that highly doped, rough-edged 13-AGNRs exhibit a lower bandgap. Moreover, n-doped rough-edged 13-AGNRFETs with a channel of higher doping concentration have better gate control and are less affected by leakage current because they demonstrate a higher current ratio and lower off-current. Furthermore, highly n-doped rough-edged 13-AGNRFETs have better channel control and are less affected by the short channel effect due to the lower value of subthreshold swing and drain-induced barrier lowering. The inclusion of dopants enhances the on-current by introducing more charge carriers in the highly n-doped, rough-edged channel. This research highlights the importance of optimizing doping concentrations for enhancing GNRFET-based device performance, making them viable for applications in nanoelectronics.

• Computers and Concrete
• /
• v.28 no.5
• /
• pp.451-463
• /
• 2021

Inorganic basalt fiber (BF) is a novel sort of commercial concrete fiber which is made with basalt rocks. Previous studies have not sufficiently handled the behavior of self-compacted concrete, at elevated temperature, containing basalt fiber. Present endeavor covers experimental work to examine the characteristics of this material at high temperature considering different fiber content and applied temperature. Different tests were carried out to measure the mechanical properties such as compressive strength (fc), modulus of elasticity (E), Poisson's ratio, splitting tensile strength (fsplit), flexural strength (fflex), and slant shear strength (fslant) of HSC and hybrid concrete. Gene expression programming (GEP) was employed to propose new constitutive relationships depending on experimental data. It was noticed from the testing records that there is no remarkable effect of BF on the Poisson's ratio and modulus of elasticity of self-compacted concrete. The flexural strength of basalt fiber self-compacted concrete was not sensitive to temperature in comparison to other mechanical properties of concrete. Fiber volume fraction of 0.25% was found to be the optimum to some extend according to degradation of strength. The proposed GEP models were in good matching with the experimental results.

• Journal of the Korean Geotechnical Society
• /
• v.23 no.3
• /
• pp.15-24
• /
• 2007

This paper will present a simple approach (or predicting layer deformation of unbound pavement materials with stress-dependent material properties. The approach is based on an uncoupled formulation in which the resilient and deformation response of unbound materials are considered separately. As a result, an uncoupled approach incorporating a resilient stiffness and Poisson's ratio model is able to simulate field measured deformation in pavement foundations. In addition, a sensitivity analysis is conducted to identify the significant factors in the stress-dependent modulus and Poison's ratio model. The predicted trends of deformation from this analysis are presented and discussed.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.6
• /
• pp.1338-1342
• /
• 2011

In this paper, threshold voltage characteristics have been analyzed as one of short channel effects occurred in double gate(DG)MOSFET to be next-generation devices. The Gaussian function to be nearly experimental distribution has been used as carrier distribution to solve Poisson's equation, and threshold voltage has been investigated according to projected range and standard projected deviation, variables of Gaussian function. The analytical potential distribution model has been derived from Poisson's equation, and threshold voltage has been obtained from this model. Since threshold voltage has been defined as gate voltage when surface potential is twice of Fermi potential, threshold voltage has been derived from analytical model of surface potential. Those results of this potential model are compared with those of numerical simulation to verify this model. As a result, since potential model presented in this paper is good agreement with numerical model, the threshold voltage characteristics have been considered according to the doping profile of DGMOSFET.

• Journal of Applied Reliability
• /
• v.16 no.3
• /
• pp.192-201
• /
• 2016

Purpose: In this paper, we propose the output model of the optimal inventory requirements of the Maintenance Float (M/F). Weapon systems were modernized and increased costs. Thus, the complexity increases with. Alternatives to achieve the goal of availability of weapon systems and to reduce life-cycle cost are required. Especially, securing spare parts is more effective than adding the amount of equipment or maintenance facilities to achieve the goal of availability and reduce life cycle costs. However, securing spare parts and repair costs are directly related, so exact requirements are needed. Methods: Three kinds of methods (Calculation method of applying the Poisson distribution, Calculation method of considering the number of CSP, and Calculation method of applying M&S program) that this paper proposed compare the influence of the availability and the amount of spare parts. Result: We calculate the cost of M/F when the operational availability is over than 80% and compare that result. The biggest cost was calculated from the Poisson distribution method. We found that requirements and unit price is the key factor that gives a significant effect. Conclusion: These three kinds of methods can be used as a basis for Maintenance Float calculation. Among them, the calculation method based on CSP is optimal replacement equipment requirements calculation method.