• Fire Science and Engineering
• /
• v.26 no.6
• /
• pp.24-30
• /
• 2012

This study is on the method of the detection for flame and series arc which can be happened at poor contact point added a vibration in part of contact point of low voltage line. In general, the causes of electric fire are over current, short circuit, poor contact, ect. The over-current or short circuit among those causes is detected by measuring a instant current value, but poor contact is difficult to detect by measuring a excessive value of the voltage and current and a distortion of waveforms. And therefore, in this paper, it is studied on the optimal technique of the arc judgement using fuzzy logic and MDET (Multi Dimension Estimation Technique). And it carries out the simulation for arc detection and the experiment for controller and load test. In result, the controller and detection algoristhm, is classified with normal wave and abnormal arc wave without relation with each loads and so the controller can detect a series arc successfully.

• Journal of the Korea Convergence Society
• /
• v.11 no.11
• /
• pp.239-247
• /
• 2020

This study is about design and verification of stress reduction of bearings for wind turbines. In a slewing bearing having a typical four-contact structure, the contact point moves to the end of the raceway due to a large moment load, resulting in a stress concentration. A bearing was designed to reduce such contact point movement. The deformation behavior of typical ball bearings and newly designed bearings was calculated through finite element analysis under ultimate load by replacing the ball with a spring element. The contact stress between the ball and the raceway was calculated by finite element analysis by inputting the deformation behavior analysis result as a boundary condition. The effectiveness of the bearing stress analysis method using spring elements was verified through comparison of the contact stress according to the bearing structure.

• Journal of the Korean Society of Industry Convergence
• /
• v.26 no.5
• /
• pp.925-936
• /
• 2023

Currently, due to the rapid increase in power demand and the increase in capacity of power converters, the capacity of electromagnetic contactors is also increasing, and the burden on SMPS for the power that can drive them is increasing. Although the initial starting operation current of an electromagnetic contactor is significantly larger than the holding current for maintaining contact, most electromagnetic contactors apply the same voltage as the initial starting operation. An electromagnetic contactor must continuously apply a holding current to maintain the contact point, and the larger the capacity, the larger the current must be applied. This paper proposes a two-level magnetic contactor drive that allows setting the initial starting operation current to fully attach the contact point of the magnetic contactor and the holding current to maintain subsequent operation. In addition, a low-cost drive topology of analog and digital methods was proposed for various field applications, and an algorithm based on the ripple of the excitation current was proposed to determine whether the magnetic contactor was opened or closed without using a separate contact point. The feasibility of the proposed method was proven through Psim simulation experiments.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.272-272
• /
• 2009

Screen-printing metal contact is typically applied to the solar cells for mass production. And metal paste is used widely for rear contact formation of silicon solar cells. However, Screen-printing solar cell metal paste contact has low aspect ratio, low accuracy, high resistivity, hard control of unclean process. In this paper is to develop resistivity of rear contact for silicon solar cells applications. 4-point prove result, This resistivity of rear contact by Al evaporation was measured about $3.56{\times}10^6{\Omega}{\cdot}cm$ less than screen printed solar cell about $52.6{\times}10^6{\Omega}{\cdot}cm$.

• Journal of KSNVE
• /
• v.7 no.6
• /
• pp.953-958
• /
• 1997

Corrugation of railway track can be caused by the various dynamic behaviors of traveling wheels and track. In this paper, the coupled vibrations of traveling wheel and railway track are analyzed as the cause of corrugations. To analyze the coupled vibration, the track supported by the sleepers and the traveling wheels are identified to the elastically supported infinite beam and the spring-mass system which runs at constant speed. The Hertzian contact spring is considered between the infinite beam and spring-mass system are calculated. The cause and development of rail corrugation are discussed in the view point of contact force fluctuation affected by the elastic supports and the corrugated surface profile on the track. By the obtained results, the possibilities of resonance are checked between the excitation by the corrugated surface profile and the natural frequency of contact spring-mass system. It may be thought to a development of railway corrugation.

• Journal of Multimedia Information System
• /
• v.5 no.3
• /
• pp.179-188
• /
• 2018

In order to overcome the problems of contact palmprint recognition, a non-contact palmprint recognition system is developed on personal computer (PC) platform. Three methods, namely "double-line-single-point" (DLSP), "double-assistant-crosshair" (DAC) and "none-assistant-graphic" (NAG), are implemented for the palmprint localization to solve the severe technical challenges, including the complex background, variant illuminations, uncontrollable locations and gestures of hands. In NAG, hand segmentation and the cropping of region of interest are performed without any assistant graphics. The convex hull contour of hand helps detect the outside contour of little finger as well as the valley bottom between thumb and index finger. The three methods of palmprint localization have good operating efficiency and can meet the performance requirements of real-time system. Furthermore, an attendance system on PC platform is designed and developed based on non-contact palmprint recognition.

• Journal of Mechanical Science and Technology
• /
• v.16 no.3
• /
• pp.344-353
• /
• 2002

A reliable computational heat transfer model has been investigated to define the heat transfer characteristics of a spray column direct contact heat exchanger, which is often utilized in the process involving counterflows for heat and mass transfer operations. Most of the previous studies investigated are one-dimensional unsteady solutions based on rather fragmentary experimental data. Development of a multidimensional numerical model and a computational algorithm are essential to analyze the inherent multidimensional characteristics of a direct contact heat exchanger. The present study has been carried out numerically and establishes a solid simulation algorithm for the operation of a direct contact heat exchanger. Operational and system parameters such as the speed and direction of working fluid droplets at the injection point, and the effects of aspect ratio and void fraction of continuous fluid are examined thoroughly as well to assess their influence on the performance of a spray column.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.1
• /
• pp.26-34
• /
• 1998

In this paper, a force control algorithm for edge following task is suggested. Through the contact state modeling between rigid part and end-effector of robot, contact force and contact angle that are essencial parameters to build the control strategies for following movement of end-effector are derived. From these two parameters, we discriminate the every contact state into 8 cases and calculate the new moving position and direction simply. For the experiment. RX90 robot from Staubli with robot language V$^{+}$ is applied and F/T sensor is attached to the wrist of robot with RCC. Finally, 3 edge following experiments including the following of corner point are executed with successful results.s.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2003.11a
• /
• pp.348-354
• /
• 2003

An analysis of the dynamic behavior between disk and roller has been performed when the torque is transmitted to toroidal IVT (Infinitely Variable Transmission). The contact area, shape and pressure with elliptical shapes between disk and roller are computed as the transmission ratios are changed. This study will give the information of contact shapes between roller-input dist and roller-output disk which are working under the most severe condition. The computed results are expected to guide the design criteria for the enhanced endurance li(e. Furthermore, the investigation of contact behaviors is very crucial to develop the traction oil that the efficiency of IVT system is most dependent on.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1997.04a
• /
• pp.241-246
• /
• 1997

Corrugation of railway track can be caused by the various dynamic behaviors of traveling wheels and track. In this paper, the coupled vibrations of traveling wheel and railway track are analyzed as the cause of corrugations. To analyze the coupled vibration, the track supported by the sleepers and the traveling wheels are identified to the elastically supported infinite beam and the spring-mass system which runs at constant speed. The Hertzian contact spring is considered between the infinite beam and spring-mass system. The dynamic responses of elastically supported infinite beam and spring-mass system are calculated. The cause and development of rail corrugation are discussed in the view point of contact force fluctuation affected by the elastic supports and the corrugated surface profile on the track. By the obtained results, the possibilities of resonance are checked between the excitation by the corrugated surface profile and the natural frequency of contact spring-mass system. It may be thought to a development of railway corrugation.