• The Transactions of the Korean Institute of Power Electronics
• /
• v.19 no.3
• /
• pp.201-210
• /
• 2014

In this paper, dc-link voltage control of a grid-connected QZSI is presented. Since the input current of the ZSI is discontinuous, a capacity with relatively large capacitance should be connected to the output of the PV array in order to reduce the current ripple. Due to the presence of the impedance network inductor in series with the PV array, the QZSI can achieve continuous input current flow. Several dc-link voltage control methods are compared and the method for power quality improvement is also presented. The performance of the proposed method is verified through both simulation and experimental results.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.1
• /
• pp.213-224
• /
• 2010

In this paper, we propose an algorithm both geometric correction using a grid point image and radiometric adaptive projection that dependent upon the luminance of the input image and that of the background. This method projects and captures the grid point image then calculates the geometrically corrected position by difference between the two images. Next, to compensate color, a corrected image is calculated by the ratio divided luminance of an input image by luminance of arbitrary surface. In addition, we found the scaling factor which controls the contrast to avoid clipping error. At this time, the scaling factor is dependent on mean image lightness when background is determined. Experimental results show that the proposed method achieves good performance and is able to reduce the perceived color clipping and artifacts, better approximating the projection on a white screen.

• Journal of Electrical Engineering and Technology
• /
• v.5 no.4
• /
• pp.606-613
• /
• 2010

This paper proposes a novel current-based maximum power point tracking (CMPPT) method for a single-phase photovoltaic power conditioning system (PV PCS) by using a modified incremental conductance method. The CMPPT method simplifies the entire control structure of the power conditioning system and uses an inherent current source characteristic of solar cell arrays. Therefore, it exhibits robust and fast response under a rapidly changing environmental condition. Digital phase locked loop technique using an all-pass filter is also introduced to detect the phase of grid voltage, as well as the peak voltage. Controllers of dc/dc boost converter, dc-link voltage, and dc/ac inverter are designed for coordinated operation. Furthermore, a current control using a pseudo synchronous d-q transformation is employed for grid current control with unity power factor. A 3 kW prototype PV PCS is built, and its experimental results are given to verify the effectiveness of the proposed control schemes.

• Proceedings of the KIPE Conference
• /
• 2019.07a
• /
• pp.207-209
• /
• 2019

This paper proposes a grid-tied photovoltaic (PV) system, consisting of Voltage-fed dual-active-bridge (DAB) dc-dc converter with single phase inverter. The proposed converter allows a small dc-link capacitor, so that system reliability can be improved by replacing electrolytic capacitors with film capacitors. The double line frequency free maximum power point tracking (MPPT) is also realized in the proposed converter by using Ripple Correlation method. First of all, to eliminate the double line frequency ripple which influence the reduction of DC source capacitance, control is developed. Then, a designing of Current control in DQ frame is analyzed and to fulfill the international harmonics standards such as IEEE 519 and P1547, $3^{rd}$ harmonic in the grid is directly compensated by the feedforward terms generated by the PR controller with the grid current in stationary frame to achieve desire Total Harmonic Distortion (THD). 5-kW PV converter and inverter module with a small dc-link film capacitor was built in the laboratory with the proposed control and MPPT algorithm. Experimental results are given to validate the converter performance.

• The KIPS Transactions:PartA
• /
• v.11A no.4
• /
• pp.267-276
• /
• 2004

The modeling methods of routing region used in the automatic placement/routing system are a grid and non-grid. Because the gird method is curbed by its size and a board if the electrical and physical elements on PCB are of small quantity, it has many memories. Therefore, it has demerit which decreases the speed of automatic placement/routing. The Shape-based type, non-grid method, makes the shapes exist as an in dividual element in a memory by using a region-processing method. Each individual element needs very small memory since it has its unique data size. Therefore, this paper aimed to develope the automatic placement/routing system which can automatically place and route the PCB without dissipation of memory at a high speed. To this aim, the auction algorithm method was applied which can make the memories be most rapidly reached from the original point to various destinations. Also, this system was developed by the Visual C++ in the Widows environment of IBM Pentium computer in order to use it in an individual PC system.

• Journal of Navigation and Port Research
• /
• v.36 no.10
• /
• pp.825-832
• /
• 2012

GPS signal delay that caused by dry gases and water vapor in troposphere is a main error source of GPS point positioning and it must be eliminated for precise point positioning. In this paper, we implemented to generate tropospheric delay grid map over the Korean Peninsula based on post-processing method by using the GPS permanent station network in order to determine the availability of tropospheric delay generation algorithm. GIPSY 5.0 was used for GPS data process and nationwide AWS observation network was used to calculate the amount of dry delay and wet delay separately. As the result of grid map's accuracy analysis, the RMSE between grid map data and GPS site data was 0.7mm in ZHD, 7.6mm in ZWD and 8.5mm in ZTD. After grid map accuracy analysis, we applied the calculated tropospheric delay grid map to single frequency relative positioning algorithm and analyzed the positioning accuracy enhancement. As the result, positioning accuracy was improved up to 36% in case of relative positioning of Suwon(SUWN) and Mokpo(MKPO), that the baseline distance is about 297km.

• Korean Journal of Materials Research
• /
• v.31 no.2
• /
• pp.75-83
• /
• 2021

To cope with automobile exhaust gas regulations, ISG (Idling Stop & Go) and charging control systems are applied to HEVs (Hybrid Electric Vehicle) for the purpose of improving fuel economy. These systems require quick charge/discharge performance at high current. To satisfy this characteristic, improvement of the positive electrode plate is studied to improve the charge/discharge process and performance of AGM(Absorbent Glass Mat) lead-acid batteries applied to ISG automotive systems. The bonding between grid and A.M (Active Material) can be improved by applying the Sand-Blasting method to provide roughness to the surface of the positive grid. When the Sand-Blasting method is applied with conditions of ball speed 1,000 rpm and conveyor speed 5 M/min, ideal bonding is achieved between grid and A.M. The positive plate of each condition is applied to the AGM LAB (Absorbent Glass Mat Lead Acid Battery); then, the performance and ISG life characteristics are tested by the vehicle battery test method. In CCA, which evaluates the starting performance at -18 ℃ and 30 ℃ with high current, the advanced AGM LAB improves about 25 %. At 0 ℃ CA (Charge Acceptance), the initial charging current of the advanced AGM LAB increases about 25 %. Improving the bonding between the grid and A.M. by roughening the grid surface improves the flow of current and lowers the resistance, which is considered to have a significant effect on the high current charging/discharging area. In a Standard of Battery Association of Japan (SBA) S0101 test, after 300 A discharge, the voltage of the advanced AGM LAB with the Sand-Blasting method grid was 0.059 V higher than that of untreated grid. As the cycle progresses, the gap widens to 0.13 V at the point of 10,800 cycles. As the bonding between grid and A.M. increases through the Sand Blasting method, the slope of the discharge voltage declines gradually as the cycle progresses, showing excellent battery life characteristics. It is believed that system will exhibit excellent characteristics in the vehicle environment of the ISG system, in which charge/discharge occurs over a short time.

• Journal of the Korean Society of Safety
• /
• v.16 no.4
• /
• pp.208-212
• /
• 2001

DQM(differential quadrature method) is applied to computation of two dimensional elasticity problems in helical spring. Elastic shear stresses in an axially loaded helical spring having rectangular and square cross sections are calculated. The results are compared with those obtained using the method of successive approximations. The differential quadrature method gives good accuracy even when only a limited number of grid points is used.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.27 no.2
• /
• pp.134-141
• /
• 2022

This study presents a method for reducing current distortion that occurs when a dual-buck inverter generates reactive power. Dual-buck inverters, which are only capable of unity power factor operation, can generate reactive power capabilities by modifying a modulation technique. However, under non-unity power factor conditions, current distortion occurs at zero-crossing points of grid voltage and output current. This distortion is caused by parasitic capacitors, dead-time, and discontinuous conduction mode operation. This study proposes a modified modulation method to alleviate the current distortion at zero-crossing point of the grid voltage. A repetitive controller is applied to reduce this distortion of the output current. A 1 kVA prototype is built and tested. Simulation and experimental results demonstrate the effectiveness of the proposed method.

• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.254-260
• /
• 2000

The spacer grid is one of the main structural components in fuel assembly, which supports the fuel rods, guides cooling water, and protects the fuel assembly from the external impact load such as earthquakes. The nonlinear dynamic impact analysis is conducted by using the finite element code ABAQUS/Explicit. Boundary condition for dynamic analysis is well applied to the test condition. Simulation results also similarly predict the local buckling phenomena. In addition to the buckling parameter, the local buckling cause is examined by both simulation and test method. It is found to correspond well with the test results. Impact tests are also carried out for some specimens of the spacer grid in order to compare the results between the test and the simulation. This test is accomplished by a free fall dummy weight onto the specimen. From this test, only the uppermost and lowermost layers of the multi-cell are buckled, which implies the local buckling at the weakest point of the grid structure.