• Journal of the Korean Society of Marine Environment & Safety
• /
• v.19 no.6
• /
• pp.582-596
• /
• 2013

In order to estimate the tide and flow properties around the archipelago, around Dolsan, Choyak, Geogeom and Jindo which located in the southwestern waters of the south sea of Korea, tidal currents, residual flows and tidal energy dissipation were investigated by using 2-dimensional numerical model. The maximum speeds of tidal currents are small around Dolsando(31.92 cm/s) and large around Jindo(87.55 cm/s). The residual flow is fastest around Choyakdo where many channels and islands as compared with other study areas. The area around Jindo has the highest currents speed, but shows the flat movements. The margins between the maximum and the minimum dispersion rates of tidal energy in the areas are estimated and designate the order of values around Dolsando($392.6{\times}10^7$ erg/s), Geogeumdo($125.7{\times}10^7$ erg/s) and Jindo($23.1{\times}10^7$ erg/s) sequently. These circumstances are same as in the amplitude of M2 constituent. This means that rapid depth changes and narrow channels play an important role in tide and tidal currents energy in archipelago.

• Asian-Australasian Journal of Animal Sciences
• /
• v.21 no.2
• /
• pp.277-290
• /
• 2008

The process of wound repair involves an ordered sequence of events such as overlapping biochemical and cellular events that, in the best of circumstances, result in the restoration of both the structural and functional integrity of the damaged tissue. An important event during wound healing is the contraction of newly formed connective tissues by fibroblasts. The polypeptide growth factors, like transforming growth factor-${\beta}$(TGF-${\beta}$, insulin-like growth factor I (IGF- I) and epidermal growth factor (EGF), play very important mediator roles in the process of wound contraction. Deer antlers, as models of mammalian regeneration, are cranial appendages that develop after birth as extensions of a permanent protuberance (pedicle) on the frontal bone. Antlers contain various growth factors which stimulate dermal fibroblast growth. They are involved in digestion and respiration and are necessary for normal wound healing and skin health. In order to investigate and evaluate the effects of red deer antlers on skin wound site, the speed of full-thickness skin wound healing and the expression of IGF-I, TGF-${\beta}$ and EGF in skin wounds, three groups of skin full-thickness rat models with a high concentration of antler ointment, a low concentration of antler ointment and without antler ointment were compared. At post-injury days 0, 2, 4, 8, 16, 20, 32, 40 and 60, the skin wound area was measured, the expressions of IGF-I, TGF- ${\beta}$ and EGF mRNA were detected by reverse transcriptase polymerase chain reaction (RT-PCR) and collagen formation by sirius red dye and the localization of IGF-I, TGF-${\beta}$ and EGF peptides were inspected by histological immunohistochemical techniques. Wound healing was significantly more rapid in antler treated skins. In addition, the wound treated with a high concentration antler ointment, a low concentration antler ointment, and the control closed completely at post-injury day 40, day 44 and day 60, respectively. Via RT-PCR, the expressions of IGF-I (day 8 and day 16), TGF-${\beta}$(day 8, day 16 and day 20) and EGF (day 4, day 8, day 16, and day 32) were obviously up-regulated in high concentration antler-treated skins compared to control skins. Similar results could be seen in the histological detection of collagen dye and immunohistochemical methods using the corresponding polyclone antibodies of IGF-I, TGF-${\beta}$ and EGF. These results illustrate that antlers stimulate and accelerate the repair of cutaneous wounds.

• KIPS Transactions on Computer and Communication Systems
• /
• v.6 no.7
• /
• pp.297-306
• /
• 2017

Citizens want more accurate forecast information using Bus Information System. However, most bus information systems that use an average based short-term prediction algorithm include many errors because they do not consider the effects of the traffic flow, signal period, and halting time. In this paper, we try to improve the precision of forecast information by analyzing the influencing factors of the error, thereby making the convenience of the citizens. We analyzed the influence factors of the error using BIS data. It is shown in the analyzed data that the effects of the time characteristics and geographical conditions are mixed, and that effects on halting time and passes speed is different. Therefore, the halt time is constructed using Generalized Additive Model with explanatory variable such as hour, GPS coordinate and number of routes, and we used Hidden Markov Model to construct a pattern considering the influence of traffic flow on the unit section. As a result of the pattern construction, accurate real-time forecasting and long-term prediction of route travel time were possible. Finally, it is shown that this model is suitable for travel time prediction through statistical test between observed data and predicted data. As a result of this paper, we can provide more precise forecast information to the citizens, and we think that long-term forecasting can play an important role in decision making such as route scheduling.

• Management & Information Systems Review
• /
• v.28 no.3
• /
• pp.191-210
• /
• 2009

Internet was first designed only for sending data, but as the time passed, internet started to evolve into a broadband multi-media web that is capable of transmitting sound, video, high-capacity data and more due to the demands of internet users and the rapid changing internet-communication technology. Domestically, in January, 2000 Saerom C&T, launched a free VoIP, but due to limited ways of conversation(PC to PC) and absence of a revenue model, and bad speech quality, it had hit it's growth limit. This research studied VoIP based on technological enhancement in super-speed internet. According to IDC, domestic internet market's size was 80,800 million in 2008, and it formed a percentage of 12.5% out of the whole sound-communication market. in case of VoIP, it is able to maximize it's profit by connecting cable and wireless network, also it has a chance of becoming firm-concentrated monopoly market by fusing with IPTV. Considering the fact that our country is insignificant in MVNO revitalization, regulating organizations will play a significant roll on regulating profit between large and small businesses. Further research should be done to give VoIP a secure footing to prosper and become popularized.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.430-430
• /
• 2008

Using multi plasma enhanced chemical vapor deposition system (Multi-PECVD), p-a-Si:H deposition layer as a $p^+$ region which was annealed by laser (Q-switched fiber laser, $\lambda$ = 1064 nm) on an n-type single crystalline Si (100) plane circle wafer was prepared as new doping method for single crystalline interdigitated back contact (IBC) solar cells. As lots of earlier studies implemented, most cases dealt with the excimer (excited dimer) laserannealing or crystallization of boron with the ultraviolet wavelength range and $10^{-9}$ sec pulse duration. In this study, the Q-switched fiber laser which has higher power, longer wavelength of infrared range ($\lambda$ = 1064 nm) and longer pulse duration of $10^{-8}$ sec than excimer laser was introduced for uniformly deposited p-a-Si:H layer to be annealed and to make sheet resistance expectable as an important process for IBC solar cell $p^+$ layer on a polished n-type Si circle wafer. A $525{\mu}m$ thick n-type Si semiconductor circle wafer of (100) plane which was dipped in a buffered hydrofluoric acid solution for 30 seconds was mounted on the Multi-PECVD system for p-a-Si:H deposition layer with the ratio of $SiH_4:H_2:B_2H_6$ = 30:120:30, at $200^{\circ}C$, 50 W power, 0.2 Torr pressure for 20 minutes. 15 mm $\times$ 15 mm size laser cut samples were annealed by fiber laser with different sets of power levels and frequencies. By comparing the results of lifetime measurement and sheet resistance relation, the laser condition set of 50 mm/s of mark speed, 160 kHz of period, 21 % of power level with continuous wave mode of scanner lens showed the features of small difference of lifetime and lowering sheet resistance than before the fiber laser treatment with not much surface damages. Diode level device was made to confirm these experimental results by measuring C-V, I-V characteristics. Uniform and expectable boron doped layer can play an important role to predict the efficiency during the fabricating process of IBC solar cells.

• Journal of IKEEE
• /
• v.19 no.3
• /
• pp.311-318
• /
• 2015

This dissertation proposes method for development technology of voice and SMS(Short Message Service) alarming system based on modbus protocol. The proposed technology is composed of the following 3 stages; hardware development based on microprocessor, development of input and output driver for modem, mp3 decoder, making modbus protocol stack. In the stage of hardware development based on microprocessor, we develop hardware which receives alarm from modbus master and transmit sms message, play mp3. In the stage of development of input / ouput device driver such as modem, mp3 decoder, we develop program which control each devices. In the stage of making modbus protocol stack, voice and sms alarm system is made for receiving alarm via modbus protocol. To evaluate performance of proposed technology, we issued alarm to voice and sms alarming system on purpose. As a result, response speed of detecting alarm was 10.7ms, communication distance was 1.2Km, operating temperature was from $-25^{\circ}C$ to $70^{\circ}C$, we confirmed supporting modbus protocol. And we verified that proposed voice and sms alarming system in the thesis has a performance to be used as an industrial building alarming system.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.4
• /
• pp.659-666
• /
• 2006

Servo-motors are used as key components of automated system by performing precise motion control as accurate positioning and accurate speed regulation in response to the commands from computers and sensors. Especially, the linear brushless servo-motors have numerous advantages over the rotary servo motors which have connection with the friction induced transfer mechanism such as ball screws, timing belts, rack/pinion. This paper proposes an estimation method of unknown motor system parameters using the informations from the sinusoidal driving type linear brushless DC motor dynamics and outputs. The estimated parameters can be used to tune the controller gain and a disturbance observer. In order to meet this purpose high performance Digital Signal Processor, TMS320F240, designed originally for implementation of a Field Oriented Control(FOC) technology is adopted as a controller of the liner BLDC servo motor. Having A/D converters, PWM generators, rich I/O port internally, this servo motor application specific DSP play an important role in servo motor controller. This linear BLDC servo motor system also contains IPM(Intelligent Power Module) driver and hail sensor type current sensor module, photocoupler module for isolation of gate signals and fault signals.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.5B
• /
• pp.430-441
• /
• 2006

As the various A/V devices and home networks are delivered to users, home networks are changing to an entertainment network. It is expected that the required network bandwidth and the amount of usage of media content in home entertainment networks will be increased. Although the access networks and home networks becoming a high speed network, there remains the problems for QoS-guaranteed media content transfer in home networks. Also, in the home network, there can be network traffic caused by applications like video conferencing, video telephone, and VoIP(voice over IP) as well as inner network traffic of home network. Since media content transfer requires the real-time delivery, it is very important and basic requirement that is to transfer media content to A/V device user wants while keeping the media quality. Even though there are many middleware protocol for home networking, they provide basic device discovery and control or simple functions for QoS-guaranteed media content transfer that are not enough to provide QoS-guaranteed media transfer service that user wants. Thus, in this paper, we propose the technique based on UPnP(universal plug and play) protocol for QoS-guaranteed media content transfer in the home network. The proposed technique is compatible with UPnP and can be used with UPnP as additional functions. In this paper, we utilize VideoLAN application to verify the proposed technique. We add the additional modules that support the proposed technique's function to VideoLAN and we verify the its functions through various test scenarios.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.9 no.3
• /
• pp.148-153
• /
• 2006

This study dealt with the measurement of exhausted gas concentration, the estimation of a combustion efficiency, and the review of IMO indexing. We concentrated on establishing the basic data to take a counterplan coping with $CO_2$ regulations. The average combustion efficiency was 98% in shop test of new engines and 96.5% in sea trial test of new ships, respectively. It would become lower for the old engine or/and ship. High combustion efficiency results in high $CO_2$ emission and low combustion efficiency results in high emission of incomplete combustion products. The efficient method reducing $CO_2$ emission without an increase in noxious air pollutants would be the development of a substitute fuel and the fuel-efficient and economical engine, and the fair play among shipping agencies in a ship speed. In reviewing of IMO indexing, it is necessary to begin by analyzing the carbon content of a marine fuel for a precise estimates.

• Journal of radiological science and technology
• /
• v.29 no.4
• /
• pp.293-301
• /
• 2006

Currently, Educational program of radiological science is developed in enormous growth, our educational environments leading allied health science education program in the number of super high speed medical industry. Radiological science may be the fastest growing technologies in our medical department today. In this way, Medical industry fields converged in the daily quick, the fact that department of radiological science didn't discharged ones duties on current educational environments. The curriculum of radiological technologists that play an important part between skill and occupation's education as major and personality didn't performed one's part most effectively on current medical environments and digital radiological equipments interface. We expect improvement and suggestion to grow natural disposition as studies in the graduate of radiological science. Therefore, in this paper, current curriculum of radiological science are catched hold of trend and problems on digital radiology environments, on fact the present state of problems, for Graduate program of radiological science, graduate courses of MS and Ph.D. are suggested a reform measure of major education curriculum introduction.