• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.08a
• /
• pp.447-451
• /
• 1999

The plate crown and shape control of plate rolling has become important to obtain not only improved quality but also better yield of products and higher work ratio of rolling. Therefore, the development of a new plate crown and shape control system has been demanded in plate rolling mill. The 3rd Plate Rolling Works of POSCO introduced the new unique system

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.08a
• /
• pp.452-456
• /
• 1999

Newly constructed plate shape control system, using attached shape measuring instruments and work roll bender, was put in service in No. 2 Plate Mill, POSCO. Recently, customers demand the improvement of flatness and plate crown accuracy. Many competition Plate Mill introducted shape control system, for example, pair cross mill, work roll bender which includes shape measuring instrument and shape control mathematical models, and No. 2 Plate Mill, POSCO introducted work roll bender and shape measuring instruments. This report describes the properties of No. 2 Plate Mill shape control system and work roll bender.

• Structural Engineering and Mechanics
• /
• v.11 no.1
• /
• pp.89-104
• /
• 2001

This paper reviews the author's work on the development of relationships between solutions of the Kirchhoff (classical thin) plate theory and the Mindlin (first order shear deformation) thick plate theory. The relationships for deflections, stress-resultants, buckling loads and natural frequencies enable one to obtain the Mindlin plate solutions from the well-known Kirchhoff plate solutions for the same problem without much tedious mathematics. Sample thick plate solutions, deduced from the relationships, are presented as benchmark solutions for researchers to use in checking their numerical thick plate solutions.

• Journal of Ocean Engineering and Technology
• /
• v.15 no.3
• /
• pp.81-86
• /
• 2001

Ultrasonic travel-times obtained with the LCR ultrasonic technique have shown an ability to distinguish among three aluminum plates. The 244$\times$150mm thick, but differ in heat treatment. One is fully annealed, the second is quenched and then tempered, and the third is heat-treated to T651 plate, as received plate. Travel-times were obtained at four locations on each side of all plates. The data for both sides of each plate clearly are in very close agreement except location 1 of each plate. In order to show travel-time variation throughout the plate areas, the average travel-time for both sides of each plate were calculated. For Plate 1, the travel-time data were the highest and the data of Plate, the travel-time data were the highest and the data of Plate 2 were upper than Plate 3. Finally, the residual stresses for each plate were measured by X-ray diffraction method. The results showed a good relation. These preliminary results indicate that the LCR Ultrasonic Technique may be not only further developed for use in quality control in the manufacture of rolled aluminum plates but also industry.

• IE interfaces
• /
• v.14 no.3
• /
• pp.296-301
• /
• 2001

The focus of this study is to redesign the Korean license plate by comparing the USA's plate with European plate formed by 1-line system in order to increase a read rate of Korea license plate. And we have compared the read rate of the new design license plate with that of the present license plate and that of the license plate studied so far. As an experimental method (used in a precedent research), we use three kinds of methods that are the measurement of the read-distance, the measurement reading-rate under the short-term exposure and the measurement of the reading-rate when driving. First, three kinds of measurements for plates of five nations are performed. Then we redesign the new Korean license plate under the base of read rates obtained by five nation's plate. As alternatives, we choose five license plates. Those alternatives are the redesigned license plate, the present license plate, the license plate studied so far, and two types of eternity license plates made by the Korea Transport Institute. When we compare results of the read-distance, there is no significant in term of different the read-distance between the alternatives. But there is a significant difference in term of the misreading-rate and the read-rate when diving. Therefore, it is necessary to redesign the present license plates because of a high misreading-rate.

• Wind and Structures
• /
• v.25 no.1
• /
• pp.25-38
• /
• 2017

This study investigates the dynamic analysis of a transversely isotropic thin plate. The plate is made of hyperelastic John's material and its constitutive law is obtained by taken the Frechect derivative of the highlighted energy function with respect to the geometry of deformation. The three-dimensional equation governing the motion of the plate is expressed in terms of first Piola-Kirchhoff's stress tensor. In the reduction to an equivalent two-dimensional plate equation, the obtained model generalizes the classical plate equation of motion. It is obtained that the plate under consideration exhibits harmonic force within its planes whereas this force varnishes in the classical plate model. The presence of harmonic forces within the planes of the considered plate increases the natural and resonance frequencies of the plate in free and forced vibrations respectively. Further, the parameter characterizing the transversely isotropic structure of the plate is observed to increase the plate flexural rigidity which in turn increases both the natural and resonance frequencies. Finally, this study reinforces the view that non-classical models of problems in elasticity provide ample opportunity to reveal important phenomena which classical models often fail to apprehend.

• Korea-Australia Rheology Journal
• /
• v.19 no.2
• /
• pp.75-80
• /
• 2007

The slotted plate technique has previously been shown to be a successful method for directly measuring the static yield stress of suspensions. In this study, we further establish the usefulness of the slotted plate device as a rheometer especially at low shear rates, taking advantage of the extremely low speeds of the slotted plate technique. Newtonian fluids, a shear thinning fluid, and yield stress fluids were tested using the slotted plate device and the results were compared with those from a commercial rheometer using different standard flow geometries. The relationship between the stress on the plate and the viscosity for the slotted plate device obtained by dimensional analysis (drag) predicts a linear relationship between the force at the plate and the plate speed, consistent with the experimental data. The slotted plate device can measure viscosities at very low shear rates. The apparent viscosity - shear-rate data obtained from the slotted plate device are complementary to those obtained using a commercial rheometer. That is : the slotted plate can measure viscosity in the shear rate range $10^{-7}<\dot{\gamma}<10^{-3}\;s^{-1}$, while the commercial rheometer measures viscosity at shear rates higher than $10^{-3}\;s^{-1}$.

• Korean Journal of Community Nutrition
• /
• v.6 no.5
• /
• pp.830-836
• /
• 2001

The purposes of this study were to : (a) analyze the portion size & plate waste of normal & soft diets provided by dietetic departments in hospital, (b) investigate the factors affecting plate waste, and (c) determine the nutritional & monetary value of plate waste. A questionnaire for food preference and sensory evaluation was developed and a survey was carried out for the 46 normal diet and 56 soft diet patients in Sanggye Paik hospital in Seoul. Serving size and plate waste were weighed by the electric scale, and CAN-Pro program was used to evaluate the nutrition value. The data were analyzed using the SAS package program for descriptive analysis, t-test, ANOVA, and Pearson correlation. The average plate waste rate for normal diet and soft diet were 30.3% and 49.6%. More plate waste amount occurred on female patients'diet than male patients'diets regardless of the kind of diet. The plate waste percentage of male patients were higher than those of female on normal diet. On soft diet, patients who hospitalized in surgery or pediatrics department were higher than in other wards. Plate waste of normal diet and amount were correlated positively, but wastage and preference were correlated negatively Negative correlation was between taste and plate waste, and between temperature and plate waste, too. On the other hand, plate waste caused the deficiency of some nutrients such as Ca, Fe, Vit. B$_2$and a great monetary loss.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.05a
• /
• pp.111-114
• /
• 2005

While the existing reinforced concrete flat plate(RC flat plate) has a lot of advantages including reduced building height, it has some weak points such as many steel bars and the brittle rupture by punching shear. Compared with the RC flat plate, the post-tensioned flat plate (PT flat plate) has not only the same merits, but it also makes longer span possible and induces slab-column connections to be failed with the ductile behavior rather than with the brittle behavior by means of post-tensioning. However, it is difficult to define the joint behavior of PT flat plate under vertical and lateral loads since there are limit experimental results. For this reason, the experimental study is undertaken to investigate the comparison of behavior of PT flat plate and RC flat plate, and how flat plate(Gravity Load Resisting System) is displaced as lateral loads, like the wind and the earthquake, are occur. The result of this experiment shows that PT flat plate is generally superior to RC flat plate in terms of controlling crack, postponing stiffness deterioration, energy dissipation, etc.

• Food Science of Animal Resources
• /
• v.18 no.3
• /
• pp.203-208
• /
• 1998

The study was carried out to screen mutagenicity of smoking materials for the determination of optimum smoking temperature for meat products. Wood materials employed for smoking were oak and apple trees. Temperatures of the generator for manufacturing of smoke flavoring were set to 250$^{\circ}C$, 400$^{\circ}C$ and 500$^{\circ}C$, respectively. Mutagenic activities of smoke flavoring were assayed according to Ames test using Salmonella typhimurium TA98 and TA 100. In oak wood smoke flavoring, Salmonella typhimurium TA98 without S-9 mix showed strong mutagenic activities at the concentration of 6$\mu\textrm{g}$/plate(250$^{\circ}C$), 4$\mu\textrm{g}$/plate(400$^{circ}C$) and 6$\mu\textrm{g}$/plate(500$^{\circ}C$). Salmonella typhimurium TA100 with S-9 mix showed strong mutagenic activities at the concentration of 10$\mu\textrm{g}$/plate(250$^{\circ}C$), 20$\mu\textrm{g}$/plate(400$^{\circ}C$) and 10$\mu\textrm{g}$/plate(500$^{\circ}C$). Salmonella typhimurium TA98 with S-9 mix showed strong mutagenic activities at the concentration of 30$\mu\textrm{g}$/plate(250$^{\circ}C$), 40$\mu\textrm{g}$/plate(400$^{\circ}C$) and 20$\mu\textrm{g}$/plate(500$^{\circ}C$). Salmonella typhimurium TA100 with S-9 mix showed strong mutagenic activities at the concentration of 30$\mu\textrm{g}$/plate(250$^{\circ}C$), 50$\mu\textrm{g}$/plate(400$^{\circ}C$) and 20$\mu\textrm{g}$/plate(500$^{\circ}C$). Salmonella typhimurium TA100 without S-9 mix showed strong mutagenic activities at the concentration of 10$\mu\textrm{g}$/plate(250$^{\circ}C$), 20$\mu\textrm{g}$/plate(400$^{\circ}C$) and 20$\mu\textrm{g}$/plate(500$^{\circ}C$). Salmonella typhimurium TA98 with S-9 mix showed strong mutagenic activities at the concentration of 30$\mu\textrm{g}$/plate(250$^{\circ}C$), 40$\mu\textrm{g}$/plate(400$^{\circ}C$) and30$\mu\textrm{g}$/plate(500$^{\circ}C$). Salmonella typhimurium TA100 with S-9 mix showed strong mutagenic activities at the concentrations 30$\mu\textrm{g}$/plate(500$^{\circ}C$). Salmonella typhimurium TA100 with S-9 mix showed strong mutagenic activities at the concentration of 30$\mu\textrm{g}$/plate(250$^{\circ}C$), 20$\mu\textrm{g}$/plate(400$^{\circ}C$) and 30$\mu\textrm{g}$/plate(500$^{\circ}C$). From these results, it could be concluded that optimum smoking temperature for meat products should be set below 400$^{\circ}C$, that the compounds like benzo[a]pyrene etc. contain a variety of mutagenic potentials, which could be generated at the higher smoking temperature.