• 한국건설순환자원학회논문집
• /
• 제2권1호
• /
• pp.19-25
• /
• 2014

본 연구에서는 천연섬유인 양마를 섬유보강 콘크리트에 사용하기 위한 방안으로, 양마의 혼입량에 따른 콘크리트의 역학적 특성을 실험적으로 확인하였다. 양마는 표면이 거칠고 섬유의 인장력 및 부식저항성이 우수하기 때문에, 섬유보강재로 적용할 경우에 콘크리트의 인장강도 및 부착력 증대에 의한 균열저감 효과, 그리고 이산화탄소를 저감하는 친환경 재료로 기대된다. 이러한 연구를 위하여 기본배합 조건에 양마의 혼입량 4종류(0, 0.3, 0.6 및 $0.9kg/m^3$)를 대상으로 슬럼프, 공기량, 소성수축 균열 및 압축강도, 할열인장강도, 휨강도, 그리고 건조수축량 등에 대한 성능시험을 실시하였다. 실험결과, 양마의 혼입량이 증가할수록 슬럼프 저하 및 공기량 증대현상이 나타났지만, 차이는 크지 않았다. 특히, 할열인장강도 및 휨강도 증진에 매우 효과적이며, 소성수축균열 및 건조수축량 저감에도 큰 효과가 있는 것으로 나타났다. 따라서 콘크리트의 역학적 성능, 경제성 등을 고려하여 양마의 혼입량은 $0.6kg/m^3$로 사용하는 것이 가장 적합한 것으로 나타났으며, 향후 사용성 및 비교시험을 통한 현장적용성의 검토가 필요할 것으로 사료된다.

• Archives of Plastic Surgery
• /
• 제35권3호
• /
• pp.248-254
• /
• 2008

Purpose: Human acellular dermal matrix(ADM) is widely used in the treatment of congenital anomalies and soft tissue deficiencies. But it is rapidly degraded in the body and does not provide satisfactory results. There is a need to improve collagen fiber stability through various methods and ultimately regulate the speed of degradation. Methods: The ADMs were added with various cross-linking agents called glutaraldehyde, dimethyl 3,3'-dithiobispropionimidate to produce cross-linked acellular dermal matrices. 1,4-butanediol diglycidyl ether solution was applied with a pH of 4.5 and 9.0, respectively. The stability of cross-linked dermal matrix was observed by measuring the shrinkage temperature and the degradation rates. The cross- and non-cross linked dermis were placed in the rat abdomen and obtained after 8, 12 and 16 weeks. Results: The shrinkage temperature significantly increased and the degradation rate significantly decreased, compared to the control(p<0.05). All of cross-linked dermises were observed grossly in 16 weeks, but most of non-cross linked dermis were absorbed in 8 weeks. Histologically, the control group ADM was found to have been infiltrated with fibroblasts and most of dermal stroma were transformed into the host collagen fibers. However, infiltration of fibroblasts in the experiment was insignificant and the original collagen structure was intact. Conclusion: Collagen cross-linking increases the structural stability and decreases degradation of acellular dermis. Therefore, decrease in body absorption and increase in duration can be expected.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.864-869
• /
• 2004

It is net easy to predict the shrinkage rate of a plastic injection mold in its design process. The shrinkage rate should be considered as one of the important performances to produce the reliable products. The shrinkage rate can be determined by suing the CAE tools in the design produces. However, since the analysis can take minutes to hours, the high computational costs of performing the analysis limit their use in design optimization. In this study, the surrogate models based on the DACE is used in lien of the original models, facilitating design optimization.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.223-226
• /
• 2004

It is net easy to predict the shrinkage rate of a plastic injection mold in its design process. The shrinkage rate should be considered as one of the important performances to produce the reliable products. The shrinkage rate can be determined by suing the CAE tools in the design produces. However, since the analysis can take minutes to hours, the high computational costs of performing the analysis limit their use in design optimization. In this study, the surrogate models based on the RSM is used in lien of the original models, facilitating design optimization.

• 대한기계학회논문집
• /
• 제14권2호
• /
• pp.269-275
• /
• 1990

Nonaxisymmetric bifurcation behaviours of composite tubes two different materials subjected to uniform radial shrinkage at the external surface have been investigated and compared with those of single tube. The effect of material parameters normalized with respect to those of outer tube upon the bifurcation point and corresponding mode has been clarified. The parameters substantially affect the bifurcation mode with long-wavelength so that the composite tube with low hardening exponent or with high yield stress of inner tube destabilizes the overall deformation of the tube. However surface type bifurcation, short-wavelength mode, shown on the traction-free inner surface is hardly affected by the material parameters. The surface type bifurcation completely depends on the material characteristics of inner tube and the bifurcation point of composite tube almost coincides with the of single tube.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1996년도 봄 학술발표회 논문집
• /
• pp.202-207
• /
• 1996

Recently, the mortar crack on floor is very serious in construction field, e.g. the crack due to plastic shrinkage and the crack due to drying shrinkage. To prevent this kind of crack, optimum mix propertions not only satisfying the required workability but also minimizing the unit water content were selected. And the expansion admixtures were used to compensate the shrinkage of mortar. This study shows that water/cement ratio used in construction field is about 64%. Even if we reduce water/cement ratio of mortar by the appropriate use the fine aggregate with high fineness modulus and superplastizer, floor mortar can have the required workability. The equations between mortar flow and water/cement ratio, sand/cement ratio, fineness modulus of fine aggregate were proposed in this study. And this equation may provide available mix proportions of floor mortar.

• 한국정밀공학회지
• /
• 제16권11호
• /
• pp.224-233
• /
• 1999

The quality of injection molded parts is affected by the variables such as materials, design variables of part and mold, molding machine, and processing conditions. It is difficult to consider all the variables at the same time to predict the quality. In this paper neural network was applied to analyze the relationship between processing conditions and volumetric shrinkage of part. Engineering plastic gear was used for the study, and the learning data was extracted by the simulation software like Moldflow. Results of neural network was good agreement with simulation results. Nonlinear regression model was formulated using the test data of 3,125 obtained from neural network, Optimal processing conditions were calculated to minimize the volumetric shrinkage of molded part by the application of RQP(Recursive Quadratic Programming) algorithm.

• 한국기계가공학회지
• /
• 제9권2호
• /
• pp.60-65
• /
• 2010

Injection molding process is one of the popular manufacturing methods to produce plastic parts with high efficiency and low cost. The tub-drum for drum type washer is made by an insert injection molding process with aluminum alloy insert of windmill type and has a big and complex structure consisted of many ribs to sustain the strength. In this paper, the volumetric shrinkages of rib part and bottom part surrounded by a windmill type insert are analyzed according to the vertical and circumferential direction of tub-drum. Volumetric shrinkage and its difference according to the height or radius of tub drum inform the designer to reduce the warpage of tub drum, and the optimal design of tub drum can be done from the those results. The change of volumetric shrinkage according to packing pressure is also analyzed. It is very important to analyze the volumetric shrinkage of tub drum because it generates the wearing phenomena at the rotating part connected to an aluminum alloy insert due to the warpage of tub drum.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2005년도 International Meeting on Information Displayvol.II
• /
• pp.988-990
• /
• 2005

A 5.0-inch plastic TFT-LCD with the resolution of $400{\times}3{\times}300$ lines (120ppi) was developed. The device is a transmissive type with the transparent PES plastic substrates. The PES films with one side barrier coating were used for the device. In order to produce the high resolution display device, the alignments between all the layers for the TFT and CF are essential. The fundamental shrinkage effect and the thermal expansion behavior of the plastic substrates with and without the barrier coatings were studied. The proper annealing processes followed by immediate second bar-rier coating processes provide the optimal alignment between all the layers of the TFT and CF..

• Journal of Advanced Marine Engineering and Technology
• /
• 제34권2호
• /
• pp.289-295
• /
• 2010

플락스틱 재료를 사용한 가공법 중에서 가장 보편적인 가공법이 사출성형이다. 플라스틱 재료의 활용도는 지속적으로 증가하고 있으며, 신소재 등의 개발로 그 적용범위 또한 확대되고 있다. 사출성형에서 수축현상은 수지의 종류, 즉 결정성 수지인지 비결정성 수지인지에 따라 크게 다르게 나타나며 사출성형시의 운전조건에 따라서도 다르다. 본 연구에서는 Al합금으로 제작되고 있는 인라인 스케이트의 프레임을 플라스틱 재료로 대체하기 위한 최적화 공정에 관한 것이다. 금형설계 전 해석을 통하여 성형공정이 최소화되는 런너와 게이트의 치수와 형상을 결정하겠다. 런너와 게이트의 치수 변화에 따른 제품의 사출성형성을 알아보겠다. 본 연구의 시뮬레이션에서는 사출성형해석용 소프트웨어인 Moldflow를 이용해서 해석을 수행하였다.