• 한국농공학회지
• /
• 제18권4호
• /
• pp.4226-4231
• /
• 1976

The objective of this study is to investigate the characteristics of the concrete mixture and the plastic shrinkage of concrete exposed to a rapid evaporation immediately after placement, and to measure the shringkage rate according to the cement-mixture. Drying of concrete was conducted under a controlled chamber in which the temperature was 36${\pm}$2$^{\circ}C$, the relative humidity 45${\pm}$2%, and the wind velocity 4${\pm}$1m/sec. All of the concrete mo1ds were made to have good workability as 6${\pm}$0.5cm in slump. The results obtained are as follows; 1) The evaporation rate was 3.36kg/$\textrm{km}^2$, 2.98kg/$\textrm{km}^2$ and 2.91kg/$\textrm{km}^2$ respectively for each concretemixtures 365kg, 335kg and 317kg after 5 hour exposure, and the evaporation was measured at all 55∼57% after 2 hours and additional in 10% on after 5 hours exposure. 2) The weight of the concrete were was reduced to 3.0%, 2.6% and 2.4% respectively for each of them. 3) The shrinkage of concrete was 0.87 mm/m, 0.56mm/m and 0.31 mm/m after 5 hour exposure, and the shringkage of concrete was measured at 84%, 59% and 45% after 2 hours and it in 1∼5% after 5 hour exposure and then stopped. 4) A recommendation for good concrete is that the evaporation should be minimized during 2 hours after placement of concrete, if possible.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집C
• /
• pp.621-626
• /
• 2001

Microcellular foaming process was developed at MIT in 1980's to save a quantity of raw materials and improve mechanical properties. There are many process variables in appling microcellular foaming process to the conventional injection molding process. Of all process variables, part dimension control and shrinkage are the most influential on the post molded dimension. The post molding dimensional change of thermoplastic resins is important to tool designers for predicting the specific difference of molded part vs. actual mold cavity. Generally, articles injection molded are smaller in size than the cavity; hence, the term shrinkage factor is used to define the allowance a designer specifies. It is important to consider the factors that influence molded part dimension. According to ASTM Designation: D 955, shrinkage from mold dimensions of molded plastics was measured. In injection molding, the difference between the dimensions of the mold and of the molded article produced therein from a given material may vary according to the design and operation of the mold. In this paper, shrinkage data of molded plastic parts was obtained. It can be an important information for designing optimum mold system in a microcellular foaming injection molding process.

• 한국세라믹학회지
• /
• 제38권8호
• /
• pp.716-723
• /
• 2001

시멘트 모르터의 소성수축에 의한 균열을 방지하기 위해 소성수축 특성에 관한 연구를 수행하였다. 우리나라 봄철의 대표적인 기후인 온도 20$\pm$3$^{\circ}C$, 상대습도 55%, 풍속 3.5m/s의 기후조건으로 하였으며, 모르터의 물 시멘트 비, 시멘트 골재 비, 팽창재 사용, 플라이 애쉬 치환, 수분증발을 억제하기 위한 중점제 등을 사용하여 소성수축의 특성을 검토하였다. 연구 결과 소성수축 변형은 응결시간과 밀접한 관계가 있으며 응결시간이 빠를수록 변형은 크게 나타났다. 또한 물시멘트 비에 의해서도 소성수축 변형은 큰 것으로 나타났다. 모르터에서의 골재 비율이 작거나, 플라이 애쉬의 치환율이 클수록 소성수축 변형은 매우 크게 나타났다. 중점제의 사용은 소성수축 변형을 줄이는데 효과가 있었으며, 건조수축 보상용 팽창재의 사용은 소성수축 변형율을 크게 하는데 이는 ettringite 생성에 의한 물 시멘트 비의 감소효과를 가져오기 때문이다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2004년도 춘계 학술발표회 제16권1호
• /
• pp.156-159
• /
• 2004

The intention of this study is to reduce the plastic shrinkage of the polymer modified cement mortar using the PVA fiber. The durability of PVA fiber reinforced polymer cement mortar was also evaluated. The test results of PVA fiber reinforced polymer modified cement mortar were compared with plain polymer modified cement mortar(non-fiber). In conclusion, PVA fiber reinforced polymer modified cement mortar showed an ability to reduce the total crack area and maximum crack width significantly. Also. fiber reinforced polymer modified cement mortar show improved durability performance.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2003년도 가을 학술발표회 논문집
• /
• pp.537-540
• /
• 2003

The effects of substituting cement with fly ash(10%, 15%, 20%) and different fiber addition(polypropylene, cellulose, poly vinyl alcohol), on the control of microcrack and enhanced durability performance of face slab concrete in CFRD was studied experimentally It was conducted experiments of plastic shrinkage of mortar and concrete, and drying shrinkage of concrete. Also, durability test were carried out the chloride permeability, abrasion resistance and freeze-thaw repetition. Through the experimental results, it was concluded that ploy vinyl alcohol fiber containing concrete was the most effective mixture in control of cracking and durability.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1993년도 가을 학술발표회 논문집
• /
• pp.150-155
• /
• 1993

The use of polypropylene fibers in concrete has been widely advertised by the fiber manufacturers. However, the behavior of concrete containing plastic fibers has not been fully understood. The effects of fiber on concrete have been forcused on shrinkage crack control mainly from field observation, and the mechanism and the side effect of fiber such as workability reduction have been neglicted. In this paper, the effect of fiber on workability and shrinkage properties have been studied. The addition of fiber significantly reduce workability and requires additional water to maintain the workability, which causes adversal effects on concrete properties.

• 대한기계학회논문집A
• /
• 제34권10호
• /
• pp.1549-1554
• /
• 2010

플라스틱 나사는 경량성, 내식성, 열 및 전기절연성이 우수하여 최근 금속나사 대체용도로 사용 되고 있다. 플라스틱 나사는 사출성형에 의해 제작되며 성형과정에서 수축이 발생하여 형상정밀도가 저하된다. 특히 소형 정밀나사의 경우 마이크로미터 단위의 정밀도를 요구하는 관계로 소성가공에 의해 제작되는 금속나사를 대체하기 위해서는 많은 어려움이 따른다. 본 연구에서는 사출성형 공정의 수치해석을 통해 금형설계 인자를 결정하였고, 실험계획법을 적용하여 변형량을 최소화하기 위한 성형조건을 도출함으로써 플라스틱 나사의 형상정밀도 향상을 위한 연구를 수행하였다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제13권3호통권55호
• /
• pp.188-196
• /
• 2009

콘크리트는 초기재령에 있어서 수분의 증발 및 이동으로 소성 및 건조수축 등의 수축현상이 발생한 다. 국내에서는 아령형 구속건조수축몰드를 활용한 콘크리트의 건조수축 균열 평가방법을 KS에서 규격화하여 활용하고 있으나 이는 균열발생시점 및 구속수축응력을 평가하는 방법으로 균열발생량에 관한 정량적 평가는 어려운 실정이다. 이에 본 연구에서는 콘크리트의 수축변형거동 및 균열발생량에 대한 정량적 데이터를 확보하기 위하여 판상-링형 구속시험방법을 개발하고 시험체 치수가 콘크리트의 수축균열에 미치는 영향을 검토하여 판상-링형 구속시험방법의 최적 시험체 치수 도출 및 수축균열특성에 관한 정량적 평가방법을 제안하고 그 적용성을 검증하고자 한다.

• 한국정밀공학회지
• /
• 제21권2호
• /
• pp.27-34
• /
• 2004

In the injection molding of plastic optical lenses, the molding conditions have critical effects on the quality of the molded lenses. Since there are many molding parameters involved in injection molding process, determination of the molding conditions for lens molding is very important in order to precisely control the surface contours of an optical lens. Therefore this paper presents the application of neural network in suggesting the optimized molding conditions for improving the quality of molded parts based on data of FE Analysis carried out through CAE software, Timon-3D. Suggested model in this paper, which serves to learn from the data of FE Analysis and induce the values for optimized molding conditions. has been implemented for searching the molding conditions without void and with minimized thickness shrinkage at lens center of injection molding optical lens. As the result of this study. we have confirmed that void creation at the inside of lens is primarily determined by mold temperature and thickness shrinkage at center of lens is primarily determined by the parameters such as holding pressure and mold temperature.

• 한국산학기술학회논문지
• /
• 제4권3호
• /
• pp.164-167
• /
• 2003

본 연구에서는 무선부품의 일종인 cavity filter금형을 제작하여 도금용 ABS 수지와 PC/ABS alloy 수지를 사용하여 일반사출성형과 금형온도가 높은 MmSH방식, 두 타입으로 성형품을 제작하였다. 성형품의 수축률 변화는 MmSH 방식일 때 ABS 성형품의 단위캐비티 격막부분에서 수축률이 감소되었다. 중량변화는 ABS와 PC/ABS 성형품 모두 MmSH 방식일 때 증가하였고, 성형품 표면 거칠기는 MmSH 방식일 때 모두 거칠기가 감소되었다.