• 한국진공학회지
• /
• 제7권1호
• /
• pp.43-50
• /
• 1998

원격플라즈마화학증착(RPCVD)에 의하여 파이렉스 유리 기판 위에 투명전도성 산화 주석막을 제조하였다. RPCVD공정의 주요한 조절변수는 증착시간, 사메틸주석, 산소 및 아 르곤의 유속, 라디오 주파수 출력, 및 기판온도를 포함했다. 양질의 산화주석막을 제조하고 RPCVD공정을 보다 잘 이해하기 위하여 이들 파라미터에 대한 증착속도, 전기적 저항, 광 학적 투과도 및 결정구조의 의존성을 체계적으로 살펴보았다. 산화주석막의 성질에 미치는 이들 파라미터의 영향은 복잡하게 서로 연관되어 있다. 최적화된 증착조건에서 제조된 산화 주석막은 102$\AA$/min의 증착속도, $9.7\times 10^{-3}\Omega$cm의 비저항 및 ~80%의 가시선 투과도를 나 타냈다.

• E2M - 전기 전자와 첨단 소재
• /
• 제8권2호
• /
• pp.171-175
• /
• 1995

Optimum condition of remote plasma enhanced chemical vapor deposition using orthogonal array method was chosen. Characteristics of oxide films deposited by RPECVD with SiH$_{4}$ and N$_{2}$O gases were investigated. Etching rate of the optimized SiO$_{2}$ films in P-etchant was about 6[A/s] that was almost the same as that the high temperature thermal oxide. The films showed high dielectric breakdown field of more than 7[MV/cm] and a resistivity of 8*10$^{13}$ [.ohmcm] around at 7[MV/cm]. The interface trap density of SiO$_{2}$/Si interface around the midgap derived from the high frequency C-V curve was about 5*10$^{10}$ [/cm$^{2}$eV]. It was observed that the dielectric constant of the optimized SiO$_{2}$ film was 4.29.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 하계학술대회 논문집 C
• /
• pp.1540-1542
• /
• 1997

Plasma polymerized thin films were fabricated by interelectrode capacitively coupled type apparatus. FT-IR analyses indicated that the thin film spectra are composed not only of the corresponding monomer bands but also of several new bands. Relative dielectric constant and dielectric loss tangent of thin films fabricated in the discharge power of 90[W] showed $3.212{\sim}3.805$ and $0.0026{\sim}0.0451$ in alternating frequency of $10^3{\sim}10^6$[Hz]. Contact angle measurement indicated that cross-link of the films is increased with the discharge power.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제44회 동계 정기학술대회 초록집
• /
• pp.488-488
• /
• 2013

일반적으로 sputtering 방식을 이용한 박막 증착 방법은 장치가 간단하고 고품질의 박막이나 균일한 박막을 만들 수 있는 장점이 있어 널리 사용된다. 본 연구에서는 기존의 sputtering 방식에 Modulation technology를 적용하고자 한다. Modulation technology를 이용하여 전원의 pulse on 시에는 일반적인 sputter 방식으로 기판에 박막을 증착하고 pulse off 시에는 양의 전압을 인가하여 이온빔을 발생시킨 후 기판에 입사시키는 방식을 적용하여 박막 형성의 특성을 향상시키고자한다. 이는 고온의 heater 및 이온빔이나 레이저, 플라즈마 소스 등의 추가적인 에너지원의 장치가 필요 없이 고품질의 박막의 특성을 향상시키는 기대 효과가 있다. Modulated Sputtering System (MSS)에 인가되는 전압과 전류의 특성을 관찰하였으며 MSS에 인가하는 전압과 frequency, 그리고 duty cycle 변화에 따른 이온 에너지 분포를 에너지 분석기를 통해 측정하였다. 또한 Langmuir probe를 이용한 afterglow plasma 상태에서의 이온전류를 측정하였다. 그리고, MSS 이용하여 Ti 박막을 증착하였으며 박막의 특성을 분석하기 위하여 a-step, SEM, XRD, AFM을 이용하여 두께, 결정성장면, 표면 거칠기를 측정하였다. 측정 결과 기판에 입사되는 양이온의 에너지가 증가함에 따라 (002) 결정면 방향에서 (100) 결정면 방향으로 증착되고 표면 거칠기가 낮아짐을 측정하였다. 또한 Graphite 타겟을 이용한 carbon 박막을 증착하였으며 박막의 특성을 분석하기 위하여 Raman을 이용한 분석 결과 양이온의 에너지가 증가함에 따라 박막내의 sp3 함유량이 변화함을 측정하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.1475-1480
• /
• 2004

Plasma Enhanced Chemical Vapor Deposition (PECVD) process uses unique property of plasma to modify surfaces and to achieve the high deposition rates. In this study, a vertical thermal RF-PECVD (Radio Frequency-PECVD) reactor is modeled to investigate thermal flow and the deposition rates with various shapes of the showerhead. The showerhead in the CVD reactor has the shape of a ring and gases are injected in parallel with the susceptor, which is a rotating disk. In order to achieve the high deposition rates, we have simulated the thermal flow fields in the reactor with several showerhead models. Especially the effects of the number of injection holes and the rotating speed of the susceptor are studied. Using a commercial code, CFDACE, which uses FVM (Finite Volume Method) and SIMPLE algorithm, governing equations have been solved for the pressure, mass-flow rates and temperature distributions in the CVD reactor. With the help of the Nusselt number and Sherwood number, the heat and mass transfers on the susceptor are investigated. In order to characteristics of measure the flatness of the layer, furthermore, the relative growth rate (RGR) is considered.

• Journal of Magnetics
• /
• 제6권3호
• /
• pp.90-93
• /
• 2001

Co/$Al_O_3$/NiFe and CO/$Al_O_3$/Co tunnel junctions were fabricated by a radio frequency magnetron sputtering at room temperature with hard mask on glass and $4^{\circ}$ tilt cut Si (111) substrates. The barrier layer was formed through two steps. After the Al layer was deposited, it was oxidized in the chamber of a reactive ion etching system (RIE) with $O_2$plasma at various conditions. The dependence of the TMR value and junction resistance on the thickness of Al layer (before oxidation) and oxidation parameters were investigated. Magnetoresistance value of 7% at room temperature was obtained by optimizing the Al layer thickness and oxidation conditions. Circular shape junctions on $4^{\circ}$tilt cut Si (111) substrate showed 4% magnetoresistance. Photovoltaic energy conversion effect was observed with the cross-strip geometry junctions on Si substrate.

• 산업기술연구
• /
• 제30권A호
• /
• pp.127-132
• /
• 2010

We analyzed the effects of several process variables on the $SO_2$ removal and particle growth by the dielectric barrier discharge - photocatalysts hybrid process. In this process, $SO_2$ was converted into the ammonium sulfate ($(NH_4)_2SO_4$) particles. The size and crystallinity of ammonium sulfate particles were examined by using TEM and XRD analysis. The dielectric barrier discharge reactor consisted of two zones: the first is for plasma generation and the second is for ammonium sulfate particles formation and growth. The first zone of reactor was filled with glass beads as a dielectric material. To enhance $SO_2$ removal process, the $TiO_2$ photocatalysts were coated on glass beads by dip-coating method. As the voltage applied to the plasma reactor or the pulse frequency of applied voltage increases, the $SO_2$ removal efficiency increases. Also as the initial concentration of $SO_2$ decreases or as the residence time increases, the $SO_2$ removal efficiency increases. $(NH_4)_2SO_4$ particles continue to grow by particle coagulation and surface reaction, moving inside the reactor. Larger particles in site are produced according to the increase of residence time or $SO_2$ concentrations.

• 천문학논총
• /
• 제30권2호
• /
• pp.453-455
• /
• 2015

In this paper we introduce the Plasma Physics of Active Galactic Nuclei project, which is an ongoing experiment with Korean VLBI Network (KVN) and KVN and VERA Array (KaVA) to study multi-frequency polarimetric properties on parsec scales of active galaxies. The goal of the project is to improve our understanding of fundamental jet physics, especially evolution of the relativistic outflow coupled with the large-scale magnetic field. We selected six radio-loud AGN as our targets. So far we (i) detected resolved emissions regions at 86 and 129 GHz on VLBI scales, (ii) constructed 2D spectral index maps of the outflows, and (iii) found polarizations at 22 and 43 GHz for a few targets. Here we present spectral index distributions of 3C 120 between 22 and 43 GHz and a linear polarization map of BL Lac at 43 GHz obtained with KVN.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제49권11호
• /
• pp.596-602
• /
• 2000

Diamond thin films were synthesized on WC-Co substrate at various experimental parameters using 13.56MHz RF PACVD)radio frequency plasma-assisted chemical vapor deposition). In order to increased the nucleation density, the WC-Co substrate was polished with 3${\mu}m$ diamond paste. And the WC-Co substrate was preatreated in $HNO_3\;:\;H_2O$ = 1:1 and $O_2$ plasma. In $H_2-CH_4$ gas mixture, the crystallinity of thin film increased with decreasing $CH_4$ concentration at 800W discharge power and 20torr reaction pressure. In $H_2-CH_4-O_2$ gas mixture, the crystallinity of thin film increased with increasing $O_2$ concentration at 800W discharge power, 200torr reaction pressure and 4% $CH_4$ concentration.

• 한국세라믹학회지
• /
• 제26권3호
• /
• pp.323-330
• /
• 1989

Wear restance titanium carbonitride (TiCN) films were deposited on the SKH9 tool steels and WC-Co cutting tools by plasma assisted chemical vapor deposition (PACVD) using a gaseous mixture of TiCl4, CH4, N2, H2 and Ar. The effects of the deposition temperature and RF(Radio Frequency) power on the deposition rate, chlorine content and crystallinity of the deposited layer were studied. The experimental results showed that the stable and adherent films could be obtained above the deposition temperature of 47$0^{\circ}C$ and maximum deposition rate was obtained at 485$^{\circ}C$. The deposition rate was much affected by RF power and maximum at 40W. The crystallinity of the deposited layer was improved with increasing the deposition temperature and RF power. The TiCN films deposited by PACVD contained much chlorine. The chlorine content in the TiCN films was affected by deposition conditions and decreased with improving the crystallinity of the deposited layer. The deposited TiCN films deposited at the deposition temperature of 52$0^{\circ}C$ and RF power of 40W had an uniform surface with very fine grains of about 500$\AA$ size. The microhardness of the deposited layer was 2,300Kg/$\textrm{mm}^2$.