• Structural Engineering and Mechanics
• /
• 제38권3호
• /
• pp.333-347
• /
• 2011

This paper shows the solution for an orthotropic disk under the plane strain condition obtained with complex stress functions. These stress functions were induced by Lekhnitskii and expanded by one of the authors. Regarding diametrical compression test, the finite element method poses difficulties in representing the concentrated force because the specimens must be divided into finite elements during calculation. On the other hand, the method shown in this study can exactly represent this force. Some numerical results are shown and compared with those obtained under the plane stress condition for both stress and displacement. This comparison shows that the differences between the tensile stresses occurred under the plane strain condition and also that the differences under a plane stress condition increase as the orthotropy ratio increases for some cases.

• 한국농공학회지
• /
• 제41권2호
• /
• pp.70-79
• /
• 1999

The lower ground of structure, in which the strip loads, such as earth dams and embankments , are signiificantly working on , is required to be interpreted as a state of plane strain where the strain of intermediated principal stress direction is put '0' . The plane strain state is frquently observed in actural soil engineering case. For those case, drained stress-strain and strength behavior of Iksan weathered granite soil prepared in cubical specimens with cross-anisotropic fabric was studied by conventional triaxial compression, plane strain and cubial triaxial tests with independent control of the three principal stress. All specimens were loaded under conditions of principl stress directions fixed and aligned with the directions of the material axes. As a result of research , when a ground condition is analyzed under plane strain state, the shear strength obtained from the conventional triaxial compression test can be understimated.

• Geomechanics and Engineering
• /
• 제5권6호
• /
• pp.499-517
• /
• 2013

In order to investigate shear behavior of granular materials due to excavation and associated unloading actions, load-controlled plane strain compression tests under decreasing confining pressure were performed under drained conditions and the results were compared with the conventional plane strain compression tests. Four types of granular material consisting of two quartz sands and two glass beads were used to investigate particle shape effects. It is clarified that macro stress-strain behavior is more easily influenced by stress level and stress path in sands than in glass beads. Development of localized deformation was analyzed using photogrammetry method. It was found that shear bands are generated before peak strength and shear band patterns vary during the whole shearing process. Under the same test condition, shear band thickness in the two sands was smaller than that in one type of glass beads even if the materials have almost the same mean particle size. Shear band thickness also decreased with increase of confining pressure regardless of particle shape or size. Local maximum shear strain inside shear band grew approximately linearly with global axial strain from onset of shear band to the end of softening. The growth rate is found related to shear band thickness. The wider shear band, the relatively lower the growth rate. Finally, observed shear band inclination angles were compared with classical Coulomb and Roscoe solutions and different results were found for sands and glass beads.

• 열처리공학회지
• /
• 제37권1호
• /
• pp.23-28
• /
• 2024

As global warming accelerates, the transportation industry is increasing the use of lightweight materials with the goal of reducing carbon emissions. Magnesium is a suitable material, but its poor formability limits its use, so research is needed to improve it. Rare-earth elements are known to effectively control texture development, but their high cost limits commercial. In this study, changes in microstructure and texture were investigated by adding Pb, which is expected to have a similar effect as rare-earth elements. The material used is Mg-15wt%Pb alloy. Initial specimens were obtained by rolling at 773 K to a rolling reduction of 25% and heat treatment. Afterwards, plane strain compression was performed at 723 K with a strain rate of 5×10^-2s^-1 and a strain of -0.4 to -1.0. As a result, recrystallized grains were formed within the microstructure, and the main component of the texture changed from (0,0) to (30,26). The maximum axial density was initially 10.01, but decreased to 4.23 after compression.

• 열처리공학회지
• /
• 제37권2호
• /
• pp.66-72
• /
• 2024

To investigate the effect of deformation condition on microstructure and texture formation behaviors of AZ91 magnesium alloy with three kinds of initial texure during high-temperature deformation, plane strain compression tests were carried out at high-temperature deformation conditions - temperature of 673 K~723 K, strain rate of 5 × 10^-3s^-1, up to a strain of -1.0. To clarify the texture formation behavior and crystal orientaion distribution, X-ray diffraction and EBSD measurement were conducted on mid-plane section of the specimens after electroltytic polishing. As a result of this study, it is found that the main component and the accumulation of pole density vary depending on initial texture and deformation caondition, and the formation and development basal texture components ({0001} <$10\bar{1}0$>) were observed regardless of the initial texure in all case of specimens.

• 한국지반공학회논문집
• /
• 제21권10호
• /
• pp.85-97
• /
• 2005

보강토 구조물은 그동안의 다양한 분야에서의 적용을 통해 기존의 옹벽구조물의 대체 공법으로서 그 적용성을 인정받고 있다. 최근 들어 교대 및 철도 시설 등에 적용됨에 따라 단기적인 안정성 이외에 장기적으로 지속하중 혹은 반복하중에 노출됨에 따른 장기거동에 대한 연구의 필요성이 높아가고 있다. 본 연구에서는 이러한 연구의 필요성에 근거하여 보강토체에 발생할 수 있는 장기변형 특성 고찰에 주안점을 두고 우리나라에서 생산되는 지오그리드와 화강풍화토로 형성된 보강토에 대한 지속하중 혹은 반복하중 등 다양한 하중이력에 대한 보강토 구조물의 장기 변형 특성 메카니즘을 평면변형압축(plane strain compression; PSC)시험을 통해 고찰하였다. 그 결과 보강토의 시간 의존적 압축변형은 보강토체에 작용하는 하중 특성뿐만 아니라 보강재의 역학적 특성에도 많은 영향을 받는 것으로 나타났으며, 선행하중을 작용함으로써 시간 의존적 잔류변형을 제어할 수 있는 것으로 분석되었다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1998년도 춘계학술대회논문집
• /
• pp.242-245
• /
• 1998

Effects of the anisotrpy due to the initial textures in the plane sheet on plane strain punch stretching has been investigated. In this study, the anisotropy from textures in the sheet is incoporated into the finite element process model by combining the theory of crstal plasticity. Three different textures such as random texture, plane strain compression texture and cube texture are considered. Variations of puch loads as well as thickness distributions of the sheets with three different initial textures are investigated.

• 한국재료학회지
• /
• 제27권12호
• /
• pp.679-687
• /
• 2017

A strain-gradient crystal plasticity finite element method(SGCP-FEM) was utilized to simulate the compressive deformation behaviors of single-slip, (111)[$10{\bar{1}}$], oriented FCC single-crystal micro-pillars with two different slip-plane inclination angles, $36.3^{\circ}$ and $48.7^{\circ}$, and the simulation results were compared with those from conventional crystal plasticity finite element method(CP-FEM) simulations. For the low slip-plane inclination angle, a macroscopic diagonal shear band formed along the primary slip direction in both the CP- and SGCP-FEM simulations. However, this shear deformation was limited in the SGCP-FEM, mainly due to the increased slip resistance caused by local strain gradients, which also resulted in strain hardening in the simulated flow curves. The development of a secondly active slip system was altered in the SGCP-FEM, compared to the CP-FEM, for the low slip-plane inclination angle. The shear deformation controlled by the SGCP-FEM reduced the overall crystal rotation of the micro-pillar and limited the evolution of the primary slip system, even at 10 % compression.

• 한국지반공학회논문집
• /
• 제16권4호
• /
• pp.95-105
• /
• 2000

공중낙하법에 의해 만든 등방압밀 모래공시체를 미소변형률 측정장치를 사용한 평면변형률압축시험을 실시하여 미소변형률에서 파괴후까지의 전단강성계수에 대한 이방성을 연구하였다. 세계각국의 주요 연구기관에서 사용되고 있는 7종류의 연구용 표준사 공시체를 멤브레인의 관입에 의한 오차와 변위를 외부에서 측정함으로 하여 생기는 오차(bedding error)등의 영향을 제거하여 측정한 최대주응력방향의 변형률과 최소주응력방향의 변형률을 각각 0.0001%에서 10%까지 넓은 범위에 걸친 응력-변형률 관계를 얻었다. 그 결과 최대전단강성계수 Gmax는 퇴적면과 최대주응력 $\sigma$1이 이루는 각도 $\delta$에 관계없이 일정하였다. 그러나 정규화한 Gmax는 모래의 종류에 따라 달랐다. 또 전단강성계수의 변형률 수준과 응력 수준에 대한 의존성은 $\delta$가 감소함에 따라 증가하였다.

• 한국지반공학회지:지반
• /
• 제14권4호
• /
• pp.33-46
• /
• 1998

공중낙하법에 의해 만든 등방압밀 모래공시 체를 미소변형률 측정장치를 사용한 평면변형률압축 시험을 실시하여 미소변형률에서 파괴 후까지의 강성률에 대한 이방성을 연구하였다. 세계 각국의 주요 연구기관에서 사용되고 있는 7종류의 연구용 표준사 공시체를 멤브레인의 관입에 의한 오차와 변위를 외부에서 측정함으로 하여 생기는 오차(bedding error) 등의 영향을 제거하여 측정한 최대주응력방향의 변형률과 최소주응력방향의 변형률을 각각 0.0001%에서 10%까지 넓은 범위에 걸친 응력-변형률 관계를 얻었다. 그 결과 최대 영률 $E_{max}$은 퇴적면과 최대주응력 $\delta_1$이 이루는 각도에 관계없이 일정하였다. 그러나, 정규화한$E_{max}$은 모래의 종류에 따라 달랐다. 또, 강성률의 변형률 수준과 응력 수준에 대한 의존성은 $\delta$가 감소함에 따라 증가하였다.