• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.13 no.4
• /
• pp.111-121
• /
• 1993

Changes in bed forms and subsequent changes in channel roughness by changes in water discharge are discussed with the field data collected from some alluvial rivers in Korea. This study is limited to the following condition of river flow: (1) Medium size alluvial rivers with their widths of 100 m more or less, (2) Straight and prismatic river reach with no additional causes for energy loss but bed friction, (3) Lower-flow regime with Froude number less than 0.5. Major conclusions obtained from this study can be summarized as follows: (1) For the channels considered in this study, the bed roughness expressed by Manning's n increases from 0.02 for the plane beds with no sediment motion to 0.05 for the dune beds, (2) The roughness coefficient for alluvial channels should not be estimated from Strickler-type equations developed for the fixed beds, (3) The method for determining the channel roughness suggested in the present guideline for river works, River Structure Standard, appears to be lack of generality. More research based on the field data collected in Korea is needed in order to improve the existing methods.

• Advances in aircraft and spacecraft science
• /
• v.2 no.2
• /
• pp.125-168
• /
• 2015

Dynamic aeroelastic behavior of structurally nonlinear Joined Wings is presented. Three configurations, two characterized by a different location of the joint and one presenting a direct connection between the two wings (SensorCraft-like layout) are investigated. The snap-divergence is studied from a dynamic perspective in order to assess the real response of the configuration. The investigations also focus on the flutter occurrence (critical state) and postcritical phenomena. Limit Cycle Oscillations (LCOs) are observed, possibly followed by a loss of periodicity of the solution as speed is further increased. In some cases, it is also possible to ascertain the presence of period doubling (flip-) bifurcations. Differences between flutter (Hopf's bifurcation) speed evaluated with linear and nonlinear analyses are discussed in depth in order to understand if a linear (and thus computationally less intense) representation provides an acceptable estimate of the instability properties. Both frequency- and time-domain approaches are compared. Moreover, aerodynamic solvers based on the potential flow are critically examined. In particular, it is assessed in what measure more sophisticated aerodynamic and interface models impact the aeroelastic predictions. When the use of the tools gives different results, a physical interpretation of the leading mechanism generating the mismatch is provided. In particular, for PrandtlPlane-like configurations the aeroelastic response is very sensitive to the wake's shape. As a consequence, it is suggested that a more sophisticate modeling of the wake positively impacts the reliability of aerodynamic and aeroelastic analysis. For SensorCraft-like configurations some LCOs are characterized by a non-synchronous motion of the inner and outer portion of the lower wing: the wing's tip exhibits a small oscillation during the descending or ascending phase, whereas the mid-span station describes a sinusoidal-like trajectory in the time-domain.

• Steel and Composite Structures
• /
• v.35 no.1
• /
• pp.61-76
• /
• 2020

In this paper, the dynamic behaviour of an inclined functionally graded material (FGM) beam with different boundary conditions under a moving mass is investigated based on the first-order shear deformation theory (FSDT). The material properties vary continuously along the beam thickness based on the power-law distribution. The system of motion equations is derived by using Hamilton's principle. The finite element method (FEM) is adopted to develop a general solution procedure. The moving mass is considered on the top surface of the beam instead of supposing it on the mid-plane. In order to consider the Coriolis, centrifugal accelerations and the friction force, the contact force method is used. Moreover, the effects of boundary conditions, the moving mass velocity and various material distributions are studied. For verification of the present results, a comparative fundamental frequency analysis of an FGM beam is conducted and the dynamic transverse displacements of the homogeneous and FGM beams traversed by a moving mass are compared with those in the existing literature. There is a good accord in all compared cases. In this study for the first time in dynamic analysis of the inclined FGM beams, the Coriolis and centrifugal accelerations of the moving mass are taken into account, and it is observed that these accelerations can be ignored for the low-speeds of the moving mass. The new provided results for dynamics of the inclined FGM beams traversed by a moving mass can be significant for the scientific and engineering community in the area of FGM structures.

• Journal of IKEEE
• /
• v.24 no.2
• /
• pp.536-542
• /
• 2020

This paper presents a nature-inspired wideband sprout-leaf shaped antenna with end-fire radiation pattern. A sprout-leaf shape angled-radiator was designed for wide beamwidth radiation patterns for motion detection sensors. An extended and truncated ground plane was used as a reflector for end-fire radiation patterns. To feed the balanced radiator, a broadband microstrip (MS) to coplanar stripline (CPS) balun was utilized with excellent amplitude and phase balance. The proposed antenna demonstrates wide frequency bandwidth from 8.5 to 14.5 GHz with wide beamwidth and the radiation efficiency of 90%. The measured gain is from 4 to 5 dBi and front-to-back ratio was 10 to 20 dB. It has been shown that the proposed antenna can be used for imaging sensors, phased array systems, and radars that require a wide bandwidth and a directional radiation pattern.

• Journal of the Korea Safety Management & Science
• /
• v.11 no.2
• /
• pp.103-110
• /
• 2009

The purpose of this study is to suggest a proper tread of stairs using kinematic factors and moments of the lower-limb joints in the stair decent with the 3 different treads with boimechanical method in ergonomics. 9 subjects (body masses; $59.41{\pm}7.49$, $64.03{\pm}6.65$, $67.26:{\pm}7.58$, heights; $160.50{\pm}6.35$ ages; $31.22{\pm}2.99$; parity; $1.67{\pm}0.71$) participated in three experiments that were divided by physiological symptoms (the early (0-15 weeks), middle (16-27 weeks) and last (18-39 weeks). and they walked at self-selected pace on 4 staircases 3 trials. As extending the pregnancy period, cadence was shorter but cycle time were longer more and more. As extending treads of stair decent during pregnancy, speed, stride lengths and cycle time were increased. As extending the treads of stair decent, hip and ankle moments increased but knee moments decreased in sagittal plane. There were increasing or decreasing of moments by means of treads. These changes may account for relation between the treads of stair and moments in pregnant women. The main changes of pregnant women were joint moments and kinematic factors during pregnancy period because pregnancy makes them physical changes. It is possible that joints have connection with compensation each other to maximize stability and to control gait motion. In conclusion, we suggest that the tread of stair is longer than 26cm tread. and exercise programs to improve muscle activity were necessary where joint moments were small.

• Physical Therapy Korea
• /
• v.11 no.1
• /
• pp.45-52
• /
• 2004

Altered scapular kinematics in the scapular joint is commonly believed to be a factor contributing to trunk posture. The purpose of this study was to analyze the muscle activity with several changes of the shoulder angle. Tests were performed on 10 male subjects by repeated measures. Each subject was measured while sitting in both erect and slouched trunk positions. In each sitting posture, a three-dimensional motion analysis measurement was used to measure thoracic angle and shoulder abduction angle. Measurements were taken with the shoulder abdcution angle at $0^{\circ}$, $30^{\circ}$, $60^{\circ}$, $90^{\circ}$, $120^{\circ}$, and $150^{\circ}$. By using surface Electromyography (EMG) electrodes, we recorded the activity of the upper trapezius, middle trapezius, lower trapezius, middle deltoid, and serratus anterior muscle while the subject held a 4 kg weight at each angle. The mean of root mean square (RMS) of EMG activity was calculated. The middle trapezius, lower trapezius, and middle deltoid muscle activity showed significantly higher results but serratus anterior muscle activity showed significantly lower results (p<.05). With the shoulder angle increased, the muscle activity was also significantly increased (p<.05). In conclusion, the thoracic spine posture significantly affects the scapular muscle during scapular plane abduction, and the slouched posture is associated with increased trapezius muscle activity and with decreased serratus anterior muscle activity.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.12 no.4_1
• /
• pp.137-150
• /
• 1992

A complete solution, exact to second-order, for wave motion forced by a hinged-wavemaker of variable-draft is presented. A solution for a piston type wavemaker is also obtained as a special case of a hinged-wavemaker. The laboratory waves generated by a plane wave board are shown to be composed of two components; viz., a Stokes second-order wave and a second-harnomic free wave which travels at a different speed. The amplitude of the second-harmonic free wave is relatively large in shallow water and decreases to less than 10% of the amplitude of the primary wave in deep water. Wavemakers with relatively deeper draft (i.e., hinged near the bottom) generate the free waves of smaller amplitude in shallow and intermediate water depths than the wavemakers with shallow draft. However, the opposite is predicted by theory in deep water.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.276-276
• /
• 2010

Large-area micropatterned array of Co/Ni bilayer anti-dots was fabricated using photolithography and wet etching process. The surface morphology as well as the surface topography was checked by scanning electron microscopy and atomic force microscopy, whereas the magnetic properties were studied by magneto-optical Kerr effect (MOKE) and magnetic force microscopy (MFM). Systematic studies of the magnetic-reversal mechanism, the in-plane anisotropy and the switching field properties were carried out. To get a comprehensive knowledge about the domain configuration, we also employed OOMMF simulations. It was found from the MOKE measurements that a combined effect of configurational and the magneto-crystalline anisotropy simultaneously works in such micropatterned bilayer structures. In addition, the inclusion of holes in the uniform magnetic film drastically affected the switching field. The MFM images show well-defined domain structures which are periodic in nature. The micromagnetic simulations indicate that the magnetization reversal of such a structure proceeds by formation and annihilation of domain walls, which were equally manifested by the field-dependent MFM images. The observed changes in the magnetic properties are strongly related to both the patterning that hinders the domain-wall motion and to the magneto-anisotropic bilayered structure.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.5
• /
• pp.439-446
• /
• 2016

The characteristics of bearingless main rotor of helicopter are investigated through non-rotating tests and rotating tests. The stiffness and natural frequencies of rotor blades, flexbeam, and torque tube which are core components of baearingless rotor are measured to obtain input material properties for rotor analysis. The functional test on ground for assembly of one hub with damper, snubber, and no blade is carried out to check interfaces between components, kinematics of components, and pitch motion ranges under applied loads including centrifugal load. The 4-bladed bearingless rotor with 5.82m of rotor radius is tested on the whirl tower with rotation plane of 9.65m height. The thrust and power are measured to obtain hover performance and the frequencies and dampings of the rotor are obtained by excitation of cyclic pitch by hydraulic actuators.

• Journal of Korean Foot and Ankle Society
• /
• v.14 no.1
• /
• pp.79-83
• /
• 2010

Purpose: To compare the clinical and radiological results between the anterior and posterior screw fixation for the treatment of talar neck fracture. Materials and Methods: Among 30 patients who received surgical treatment for talar neck fracture from 2001 to 2008. Twenty-seven patients with a follow-up period of more than 1 year were divided into two groups. Twelve patients were treated with anterior screw fixation and 15 patients with posterior approaches. We analyzed preoperative, postoperative and follow-up radiographs. Clinical results were evaluated by Hawkins criteria. Results: The posteriorly inserted screws were placed across the more central portion of the talar neck and perpendicular to the plane of fracture (p<0.05). There were no difference in clinical results, the duration of union, and complications including avascular necrosis between two groups. However, 2 patients complained of pain around the talonavicular joint in the anterior insertion group. Conclusion: Although the clinical results were good irrespective of insertion methods, the posterior approach of screw fixation for talar neck fractures allows for a better mechanical advantage than anterioly placed screws. This may allow early motion with a reduced risk of failure of fixation or of displacement of the fracture.