• Structural Engineering and Mechanics
• /
• v.42 no.6
• /
• pp.867-882
• /
• 2012

Analytical (Rayleigh-Ritz method) and numerical studies are carried out and buckling interaction curves are developed for simply supported plates of varying aspect ratios ranging from 1 to 5, under the combined action of in-plane shear and tension. A multi-step buckling procedure is employed in the Finite Element (FE) model instead of a regular single step analysis in view of obtaining the buckling load under the combined forces. Both the analytical (classical) and FE studies confirm the delayed shear buckling characteristics of thin plate under the combined action of shear and tension. The interaction curves are found to be linear and are found to vary with plate aspect ratio. The interaction curve developed using Rayleigh-Ritz method is found to deviate in an increasing trend from that of validated FE model as plate aspect ratio is increased beyond value of 1. It is found that the observed deviation is due to the insufficient number of terms that is been considered in the assumed deflection function of Rayleigh-Ritz method and a convergence study is suggested as a solution.

• Structural Engineering and Mechanics
• /
• v.90 no.4
• /
• pp.345-356
• /
• 2024

This paper aims to investigate the seismic behavior of double steel plate and concrete composite shear wall (DSCW) of shield buildings in nuclear power engineering through experimental study. Hence, a total of 10 specimens were tested to investigate the hysteretic performance of DSCW specimens in detail, in terms of load vs. displacement hysteretic curves, skeleton curves, failure modes, flexural strength, energy dissipation capacity. The experimental results indicated that the thickness of steel plate, vertical load and stiffener have great influence on the shear bearing capacity of shear wall, and the stud space has limited influence on the shear capacity. And finally, a novel simplified formula was proposed to predict the shear bearing capacity of composite shear wall. The predicted results showed satisfactory agreement with the experimental results.

• Physical Therapy Korea
• /
• v.19 no.1
• /
• pp.1-9
• /
• 2012

The purpose of this study was to investigate the kinematic and kinetic changes that may occur in the pelvic and spine regions during cross-legged sitting postures. Experiments were performed on sixteen healthy subjects. Data were collected while the subject sat in 4 different sitting postures for 5 seconds: uncrossed sitting with both feet on the floor (Posture A), sitting while placing his right knee on the left knee (Posture B), sitting by placing right ankle on left knee (Posture C), and sitting by placing right ankle over the left ankle (Posture D). The order of the sitting posture was random. The sagittal plane angles (pelvic tilt, lumbar A-P curve, thoracic A-P curve) and the frontal plane angles (pelvic obliquity, lumber lateral curves, thoracic lateral curves) were obtained using VICON system with 6 cameras and analyzed with Nexus software. The pressure on each buttock was measured using Tekscan. Repeated one-way analysis of variance (ANOVA) was used to compare the angle and pressure across the four postures. The Bonferroni's post hoc test was used to determine the differences between upright trunk sitting and cross-legged postures. In sagittal plane, cross-legged sitting postures showed significantly greater kyphotic curves in lumbar and thoracic spine when compared uncrossed sitting posture. Also, pelvic posterior tilting was greater in cross-legged postures. In frontal plane, only height of the right pelvic was significantly higher in Posture B than in Posture A. Finally, in Posture B, the pressure on the right buttock area was greater than Posture A and, in Posture C, the pressure on the left buttock area was greater than Posture A. However, all dependent variables in both planes did not demonstrate any significant difference among the three cross-legged postures (p>.05). The findings suggest that asymmetric changes in the pelvic and spine region secondary to the prolonged cross-legged sitting postures may cause lower back pain and deformities in the spine structures.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.4
• /
• pp.491-496
• /
• 2013

Finite element simulations of tensile tests were performed to determine the equivalent stress - equivalent plastic strain curves, critical equivalent stresses, and critical equivalent plastic strains. Then, the curves were used as inputs to finite element simulations of fracture toughness tests to determine the plane strain fracture toughness. The critical COD was taken as the COD when the equivalent plastic strain at the crack tip reached a critical value, and it was used as a crack growth criterion. The relationship between the critical COD and the critical equivalent plastic strain or the reduction of area was found. The relationship between the plane strain fracture toughness and the product of the critical equivalent stress and the critical equivalent plastic strain was also found.

• Journal of the Korean Vacuum Society
• /
• v.6 no.S1
• /
• pp.43-46
• /
• 1997

High resolution x-ray diffraction and two dimensional triple axis mapping were used to characterize a group of GaN layers of about 1.1$\mu$m grown by direct current plasma molecular beam epitaxy technique on 6H-SiC(0001). A FWHM of 11.9 arcmins for an $\omega$ scan and 1.2 arcmins for an $\omega$/2$\theta$ scan were observed. A careful study of the rocking curves showed there were some large mosaics in the GaN layer and a tilt of $0.029^{\circ}$ between the GaN layer and the SIC substrate was detected. The two dimensional triple axis mapping showed that the GaN mosaica were disoriented in the (0001) plane but rather uniformed in direction perpendicular to the plane. A mosaics were disoriented in the (0001) plane but rather uniformed in direction perpendicular to the plane. A mosaic model was deduced to explain the phenomenon and the dislocation density was estimated to be about~$10^9\;\textrm{cm}^{-2}$ acc ding to the model.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.5 no.1 s.16
• /
• pp.55-62
• /
• 2005

Parabolic arch ribs are widely used in practical. In case of circular arch ribs. Inelastic in-plane buckling behaviors were investigated by Trahair(1996). Recently Yong-lin Pi & Bradford(2004) investigated about in-plane design equation for circular arch ribs. In $1970{\sim}1980$. In-plane buckling strength about parabolic arch ribs were studied by some japan researchers (Sinke, Kuranishi). Study results of Sinke & kuranishi are only valid for rise-span ratio $0.1{\sim}0.2$. In this paper. The researchers investigated about in-plane inelastic buckling behaviors of parabolic arch ribs having rise-span ratio from 0.1 to 0.4. From the results. When the rise-span ratio increase, flexural moments increase and influence of axial force to in-plane buckling strength decrease. Finally, buckling curves for parabolic arch ribs subjected distributed loading along the axis were suggested.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.20 no.2
• /
• pp.279-284
• /
• 2010

The plane curve approach which was proposed by Boukharouba et. al. is a multi-threshold selection method through searching peak-valley based on histogram cumulative distribution function. However the method is required to select parameters to compose plane curve, and the shape of plane curve is affected according to parameters. Therefore detection of peak-valley is effected by parameters. In this paper, we propose an entropy maximizing-based method to select optimal plane curve parameters, and propose a multi-thresholding method based on the selected parameters. The effectiveness of the proposed method is demonstrated by multi-thresholding experiments on various images and comparison with other conventional thresholding methods based on histogram.

• Structural Engineering and Mechanics
• /
• v.32 no.3
• /
• pp.407-427
• /
• 2009

A fundamental solution for the transient, quasi-static, plane problems of linear viscoelasticity is introduced for a specific material. An integral equation has been found for any problem as a result of dynamic reciprocal identity which is written between this fundamental solution and the problem to be solved. The formulation is valid for the first, second and mixed boundary-value problems. This integral equation has been solved by BEM and algorithm of the BEM solution is explained on a sample, mixed boundary-value problem. The forms of time-displacement curves coincide with literature while time-surface traction curves being quite different in the results. The formulation does not have any singularity. Generalized functions and the integrals of them are used in a different form.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.8
• /
• pp.89-96
• /
• 2004

Micro-tensile testing system, consisting of a micro tensile loading system and micro-ESPI(Electronic Speckle Pattern Interferometry) system, has been developed for measurement of micro-tensile properties of thin micro-materials. Micro-tensile loading system had a load cell with the maximum capacity of 50N and micro actuator with resolution of 4.5nm in stroke. The system was used to apply a tensile load to the micro-sized specimen. During tensile loading, the micro-ESPI system acquired interferornetric speckle patterns in the deformed specimen and measured the in-plane tensile strain. The ESPI system consisted of a CCD-camera with a lens and the window-based program developed for this experiment. Using this system, stress-strain curves for 4 kinds of electrolytic copper foil 18$\square$m thick were obtained. From these curves, tensile properties, including the elastic modulus. yielding strength and tensile strength, were determined and also values of the plastic exponent and coefficient based on Ramberg-Osgood relationship were evaluated.

• Journal of the Korean Ceramic Society
• /
• v.31 no.10
• /
• pp.1099-1106
• /
• 1994

It is suggested that the microstructural toughening process in the initial rising portion of R-curves observed in polycrystalline alumina should be different from the grain bridging mechanism identified in the long crack regime. Microcracking in the advancing crack front seems to be a prerequisite for the development of unbroken bridging ligaments behind the crack tip. In order to test such a proposition, attempts were made to identify experimentally the presence of microcracks in the frontal zone of propagating cracks. In-situ observation is made of crack growth in a miniature double cantilever beam specimen of a average grain size of 10 ${\mu}{\textrm}{m}$ alumina. Presence of a few microcracks was identified in front of crack tip on the propagating crack plane. The R-curves were re-evaluated based on the observation.