• Composites Research
• /
• v.33 no.6
• /
• pp.329-335
• /
• 2020

In this study, the thermo-rheological behaivors of petroleum pitches with different softening points were studied, and a B-stage phenolic resins/petroleum pitches blends were prepared by adding petroleum pitches to the phenolic resins. As a result, the petroleum pitch with different softening points decreased the fluidity of the petroleum pitch as the Quinoline insoluble (QI) content increased and showed the viscous properties of the solid. In addition, the effect of adding petroleum pitches having different softening points on the thermo-rheological properties of phenolic resins was investigated. When petroleum pitch with a high softening point was added, the fluidity of the phenolic resin was reduced, and the hardening behavior was fast. It was possible to control the curing rate and curing behavior of the phenolic resin by adding petroleum pitches of different softening points. Among them, the phenolic resin mixture to which P-Pitch 2 was added has a higher fluidity than other blends under the same curing temperature condition.

• Carbon letters
• /
• v.1 no.2
• /
• pp.69-75
• /
• 2000

Naphtha cracking bottom oil was reformed with heat treatment and then spun at $310^{\circ}C$. These pitch-based carbon fibers were carbonized at $1000^{\circ}C$ after oxidation at $280^{\circ}C$, for 90 min. These fibers were chemically activated with molar ratio of KOH/CF (1 : 1) at different temperatures ($250{\sim}900^{\circ}C$) for 1 hr. The process of activation was characterized with DTA, TGA, BET surface area and pore size distribution. The activation of fibers by KOH was performed by several process. One is the reduction process that carbon fiber was reacted with $K_2O$ produced from dehydration process above $400^{\circ}C$. The other is the process that $K_2CO_3$ was directly reacted with carbon fiber. At $800^{\circ}C$, the activation was performed by catalyzed mechanism that $K_2O$ was obtained from the reaction of metal potassium with $CO_2$, then was changed to $K_2CO_3$. At $870^{\circ}C$, the activation was also observed that activation mechanism was promoted by metal catalyst with $CO_2$ from decomposition of $K_2CO_3$. The specific surface area of prepared activated carbon fibers was dependent on the activation mechanism. The specific surface area was in the range of $1519{\sim}2000\;cm^3/g$ and was the largest prepared at $870^{\circ}C$. The pores developed were mostly micropores which was very narrow and uniform. The total pore volume was $0.58{\sim}0.77\;cm^3/g$.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1990.10a
• /
• pp.145-150
• /
• 1990

In order to discuss the freeze-thaw durability of FRC and mechanical properties by the fiber types of FRC, experimental studies of FRC were carried out. The kinds of fiber used which are in CFRC are PAN-based and Pitch-based carbon fiber and in GFRC are alkali-resistance glass fiber. To examine the effects of the kinds, types (continuous fiber and Tow, Belt, Cloth) and contents of fiber and matrices, the following three methods CFRC and GFRC, Air cured, Water cured and Autoclaved CFRC and GFRC were tested. According to the test results, the flexural, tensile strength and toughness of FRC were remarkably influenced by types of fiber and addition of condensed silica fume. Also, freeze-thaw resistance of FRC was considerably improved in comparision to conventional mortar.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.28 no.1
• /
• pp.46-53
• /
• 2008

Ultrasonic C-scan technique is one of very popular techniques being used for detection of flaws in polymer matrix composite(PMC). However, the application of this technique is very limited for evaluation of defects in PMC fabricated by the automated fiber placement process. The purpose of this study is to develop a novel ultrasonic hybrid system based on nondestructive and non-contact ultrasonic techniques for evaluation of delamination in carbon/epoxy and carbon/PPS composite laminates. It was shown that the newly developed ultrasonic hybrid system based on dual air-coupled pitch-catch technique with ultrasonic scattering reflection concept could provide excellent image with higher resolution of delamination in PMC compared with the conventional pitch-catch method. It is expected that this ultrasonic hybrid technique can be applied for on-line inspection of flaws in PMC during the fabrication process.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.12 no.4
• /
• pp.165-171
• /
• 2002

The study on the adsorption, the surface properties and the antibacterial effects of the metal-treated pitch based activated carbon fibers was carried out. From the adsorption studies on the series of metal-treated activated carbon fiber, the specific surface areas of the metal treated activated carbon fiber obtained from BET equation were in the range of 113.2~1574 $m^2$/g for the Ag-ACFs. And that of Cu treated ACF are distributed to 688.2-887.8 $\m^2$/g. And, the specific surface areas of the Ni-treated pitch based ACFs were in the range of 692.6~895.2 $\m^2$/g. From the ${\alpha}_s$- method, 0.06~1.1 cm^3/g of the micropore volumes were obtained from Ag-ACFs. And, 0.1~0.2 cm^3/ and 0.2~0.6 cm^3/g of the micropore volumes were obtained from Cu and Ni-ACFs, respectively. And, from the SEM morphology results, it was observed that the surface of activated carbon fiber are partially blocked and coated by metal after the treatment. Finally, from the antibacterial effects of metal-treated activated carbon fiber against E. coli, the areas of antibacterial effect become larger with the increase in mole ratio of metal treated. And, from the antibacterial effects using Shake flask method against E. coli, the percentage of the effects was 92.5~100 % and the antibacterial effect was increased with the increase in mole concentration of metal treated.

• Magazine of the Korea Concrete Institute
• /
• v.3 no.3
• /
• pp.101-110
• /
• 1991

Results of an experimental study on the manufacture, the mechanical properties and watertightness of pitch - based carbon fiber reinforced fly ash. cement composites are presented in this paper. The carbon fiber reinforced fly ash. cement composites using early strength cement silica powder and a small amount of stylene butadiene rubber latex are prepared with carbon fiber, foaming agents and mixing conditions. As a result, the mechanical and physical properties such as compressive , tensile and flexural strengths, watertightness and drying shrinkage of lightweight carbon fiber reinforced fly ash cement composites are Improved by using a samll amount of stylene butadiene rubber latex. Also, the manufacturing pnx:ess technology of carbon fiber reinforced fly ash . cement composItes is developed. The development and applications of precast products of lightweight carbon fiber remforced cement composites are expected in the near future.

• Magazine of the Korea Concrete Institute
• /
• v.4 no.1
• /
• pp.107-118
• /
• 1992

In order to examine the mechanical properties of carbon fiber reinforced cement composites with silica powder PAN - based carbon fiber and Pitch- based carbon fiber, and polymer impregnators experimental studies on CFRC impregnated in polymer were carried out. The effects of types, length, and content~i of carbon fibers and matrices of fresh and hardened CFRC impregnated in polymer were examined. The test results show that compressive, tensile, and flexural strength of CFRC impregnated in polymer were much more iriCreased than those of air cured and autodaved CFIIC CFRC impregnated in polymer was also considerably effective in improving toughness, freeze thaw resistance, loss of shrinkage, and creep resist ance, compared with air cured and autoclaved CFRC.

• Korean Journal of Materials Research
• /
• v.7 no.2
• /
• pp.121-128
• /
• 1997

Two-types of carbon fiber, anisotropic- and isotropic- pitch based, were expose to isothermal oxidation in air and $CO_{2}$ gas and the weight change rates was measured by TGA apparatus. Thc oxidation rate was laster in air than in $CO_{2}$ gas, and the oxidation rare of isotropic T- 101s liher was over 23 9 times faster than that of anisotropic HM-60 filler at $600^{\circ}C$ in air. The activation energy was 36-56 Kcal/mole at lower temperature range and 6- 13 Kcal/molc at higher temperature range. It was higher that the transition temperalure 01 reaction zone(zone 1. 2, :i) of 11M-GO fiber than that of T-101s fiber, and it was higher in $CO_{2}$ gas than in air. From SEM observation, it Lvas found that the oxidation of carbon fibers was progressed through the imperfection.

• The Korean Journal of Ceramics
• /
• v.4 no.3
• /
• pp.193-198
• /
• 1998

This paper presents the effects of an initial braking velocity, a braking pressure, and the number of braking stop on the tribological behaviors for the three different C-C composites using an inertia dynamic-friction tester. The C-C composites were prepared through the processes of several cycles of pitch impregnation/carbonization with different friction surface texture such as continuous 8-harness satin fabric (ADD-1), chopped fiber (ADD-2) and chopped fiber (ADD-3) having higher fiber volume fraction on friction than ADD-2 by about 10%. ADD-1 exhibited a higher fraction coefficient (0.41~0.33) than those of ADD-2 and ADD-3 (0.32~0.26) under the various initial braking velocities and braking pressures. The fraction coefficients decreased with increasing the initial velocity and the braking pressures. Wear rate by the thickness change after every 25 stop indicated that ADD-2 and ADD-3 having 1.7~2.7 $\mu\textrm{m}$/stop/pair were much lower than that of ADD-1 showing 5.0~6.5 $\mu\textrm{m}$/stop/pair. All specimens showed a little bit lower wear rate during the middle stage than the initial and latter stages among 100 braking stops. ADD-1 showed higher friction coefficient and wear rate due to the active pull-out of the fibers, evidenced by thicker were film and wear debrises.

• Korean Chemical Engineering Research
• /
• v.43 no.6
• /
• pp.745-750
• /
• 2005

Naphtha cracking bottoms(NCB) oil was reformed by varying the heat treatment temperature, treatment time, and nitrogen flow rate in preparation of precursor pitch for isotropic pitch-based carbon fibers and activated carbon fibers. The reformed pitches were investigated in the yield, softening point, elementary analysis, and molecular weight distribution, and then the precursors reformed were melt spun to certify the optimum reforming conditions. The optimum precursor pitch was prepared when the NCB oil was reformed at $380^{\circ}C$, 3 h and 1.25 vvm $N_2$, and it's the softening point was around $240^{\circ}C$. The reforming resulted in product yield of 21 wt％. The C/H mole ratio of the precursor pitch increased from 1.07 to 1.34, the aromaticity increased from 0.85 to 0.88. The insolubles in benzene and quinoline were 30.0 wt％ and 1.5 wt％, respectively. The spinning temperature was about $50^{\circ}C$ higher than the softening point. The molecular weights of the precursor components were distributed from 250 to 1250, and 80％ of them were in the range of 250 to 700.