• Journal of the Korean Wood Science and Technology
• /
• 제39권1호
• /
• pp.53-59
• /
• 2011

시험 시편은 1개의 횡목과 2개의 종목이 직결나사못 2개로 연결된 접합부(Type-A)와 2개의 횡목과 2개의 종목이 4개의 직결나사못으로 연결된 접합부(Type-B)를 제작하였다. Type-B를 보강하기 위하여 횡목간의 연결부를 끝면거리 5D로 반턱이음하여 2개의 직결나사를 사용한 접합부(Type-C), 끝면거리 10D로 반턱이음한 접합부(Type-C1)와 끝면거리 10D, 직결나사 3개를 사용한 접합부(Type-C2)를 제작하였다. 압축형 전단 내력 시험결과 Type-B의 내력을 기준으로 Type-B를 보완한 Type-C는 약 30% 감소하였고, Type-C에서 끝면거리를 증가시킨 Type-C1은 Type-B와 비슷한 내력을 보였으며, Type-C1에서 직결나사못의 개수를 3개로 증가시킨 Type-C2는 Type-C1과 비교하여 1.28배 내력을 나타냈다. 기존 정각재를 이용한 옹벽의 접합부 중 긴 횡목과 짧은 횡목이 2개의 종목과 연결되는 접합부는 내력이 저하되기 때문에 이를 대체하기 위하여 실험을 실시하였다. 따라서 Type-B를 Type-C2로 대체한다면 옹벽 시공시 직결나사못에 의한 목재의 할렬, 파단과 시공시간이 줄어들고 접합 내력이 증가할 것으로 기대된다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 춘계학술대회논문집
• /
• pp.158-163
• /
• 2005

In this paper the aeroacoustic characteristics of a tilt-rotor system is measured by using a sealed model tilt-rotor. With a microphone array system and the do-dopplerization algorithm, the location and the characteristics of rotor noise are successfully measured. The most of high frequency noise (4kHz) is found to be located at rotor blade tips, but the low frequency tonal noise is dominant on the middle of the rotor blades. The measured tonal noise characteristics are compared to the results of theoretical calculation. At 0.5m distance from the rotor plane, measured and calculated data are relatively well matched regardless of rotating speed and collective pitch angie for the azimuthal angles between $0^{\circ}\;and\;60^{\circ}$. However, the data on the azimuthal angles between $70^{\circ}\;and\;90^{\circ}$ are not quite comparable. In addition, the compared data for far-field case (1.5m) are quite different. This is probably due to the unsteady effect which if not included in the theoretical calculation.

• 한국정밀공학회지
• /
• 제23권1호
• /
• pp.72-79
• /
• 2006

The objective of this work is to simulate the etching characteristics for the optimization on the etching process of Lead-Frame. The etching characteristics such as etching factor, etching uniformity were investigated under different the actual operating conditions. The correlation between the etching characteristics and the spray ones were analyzed to simulate the etching characteristics in the etching process. To improve the etching characteristics in the etching process, effects of the various operating conditions such as pressure, distance from nozzle tip, pipe pitch, and feed speed should be understood in detail. The spray characteristics obtained by experiment using PDA system were simulated by the Monte-Carlo simulation. The etching process model was coded by Java language. It was found that the spray characteristics were correlated with the etching ones and simulation results generally agreed well with the measured results of etching characteristics in the etching process of Lead-Frame. The optimal operating parameters were successfully found under variable conditions.

• 한국정보통신학회논문지
• /
• 제15권12호
• /
• pp.2705-2711
• /
• 2011

최근 멀티미디어 기술의 발달, 특히 음향 기술의 급격한 발달과 더불어 고품질 오디오에 대한 요구와 함께보다 현실감 있는 오디오를 재생하기 위한 실감 오디오기술 개발이 요구되고 있다. 이러한 요구를 만족시키기 위해 사용자의 가상현실 및 증강현실에서 실감나는 오디오 효과를 제공해 줄 수 있는 3차원 오디오에 대한 연구가 활발히 진행되고 있다. 본 논문에서는 증강현실에서 좀 더 나은 오디오 기술을 적용하여 실감나는 오디오 효과를 제공해 줄 수 있는 방법을 연구하고자 하였다. 연구한 내용은 가상세계와 실제세계의 현실감을 제공하기 위하여 마커 위에 띄워진 3D 모델의 움직임에 따라서 움직임에 맞는 사운드. 즉, 거리, 각도 등의 변화에 따른 사운드의 크기 및 피치 변화를 줄 수 있도록 하였다.

• 대한기계학회논문집B
• /
• 제39권6호
• /
• pp.497-504
• /
• 2015

본 논문에서는 박테리아 편모를 모사한 스프링 모델을 이용하여 박테리아의 편모의 추진적 거동에 관한 연구를 수행하였다. 본 해석에서는 상용프로그램을 사용하였으며, 별도의 회전영역 설정에 따른 수치기법의 타당성 확인과 더불어 파라미터 연구를 수행하였다. 수치해석 결과는 전반적으로 Resistive force theory와는 잘 일치하지 않았지만, Slender body theory와는 잘 일치하였다. 그리고 스프링의 회전속도, 피치, 나선반경 및 유체의 점성의 영향을 확인하였다. 또한 벽과의 거리에 따른 효과도 분석하였다.

• Tribology and Lubricants
• /
• 제26권6호
• /
• pp.311-316
• /
• 2010

Surface texturing of micro dimple or pore-shaped pattern was prepared using a fiber laser system. Surface texturing was designed to have a square pattern with a particular pitch distance for each corresponding density of 5, 10, 20, and 30%. Thermal damages such as bulges and burrs formed during laser irradiation were observed around the dimples. Thermal damages were later removed by lapping using alumina particles of $0.3{\mu}m$ in diameter. Oscillating friction tests were performed against heat-treated high speed steels under lubricated condition. The lubricant used was SAE 5W-30 automotive engine oil. Normal contact pressure and oscillating frequency was 0.28 MPa and 20 Hz, respectively. The tests were continued for 20 minutes, and friction plots were recorded for examination. Results revealed that the coefficient of friction was lowered regardless of texturing density. Moreover, the lowest coefficient of friction was obtained for 10% density texturing. It is attributed to increased lubricity due to the introduction of surface texturing. In addition, it is concluded that the optimum texturing density and pattern must be found for the best lubricity and low friction.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집B
• /
• pp.87-92
• /
• 2000

This study is to investigate the heat transfer characteristics the for a round turbulent jet impinging on the flat plate with and without rib. Liquid crystal/transient method was used to determine the Nusselt number distributions along the surface. The temperature on the surface was measured using liquid crystal and a digital color image processing system. The experiments were made fur the jet Reynolds number (Re) 23,000, the dimensionless nozzle-to-surface distance (L/d) from 2 to 10, and the rib type [height ($d_1$) 2mm, pitch (p) from 12 to 36mm]. It was found that for $L/d{\ge}6$ the average Nusselt numbers on the flat plate with rib type C ($p/d_1=16$) are higher than those without rib, mainly due to an increase in the turbulent intensity caused by flow separation, recirculation and reattachment on the wall surface.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.2219-2226
• /
• 2003

Two perforated plates are placed in parallel and staggered arrangements with a gap distance of 2 times of the hole diameter, and initial crossflow passes between the plates. Both the injection and effusion hole diameters are 10 mm, and the Reynolds number based on the hole diameter and hole-to-hole pitch are fixed to 10,000 and 6 times of the hole diameter, respectively. To investigate the effect of crossflow, the flow rate of crossflow is changed from 0.2 to 2 times of that of the impinging jet. A naphthalene sublimation method is used to determine the local heat/mass transfer coefficients on the upward facing surface of the effusion plate. With the initial crossflow, the heat/mass transfer rates on the effusion (target) plate decrease as the velocity of crossflow increases, since the crossflow induces the locally low transfer regions formed at the mid-way between the effusion holes. However, the impingement/effusion cooling with crossflow presents higher heat/mass transfer rates than the array jet impingement cooling with the same initial crossflow.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집B
• /
• pp.260-267
• /
• 2001

The objective of this study was to investigate the characteristics of jet flow and heat transfer caused by trapezoid rods array in impinging jet system. In this study, trapezoid rods have been set up in front of flat plate to serve as a turbulence promoter. The bottom width of trapezoid rod was W=4, 8mm and oblique angle were $80^{\circ}$. The space from rods to the heating surface was C=1, 2, 4mm, the pitch between each rods was P=30, 40, 50mm, and the distance from nozzle exit to flat plate was H=100, 500mm. This results were compared with the case without trapezoid rods. As a result, when rods are installed in front of the impinging plate, the acceleration of the jet flow and the eddies due to the rods seem to contribute to the heat transfer enhancement. Among test conditions, the heat transfer performance was best for the condition of W=8mm, C=1mm, P=30mm and H/B=10. The maximum heat transfer rate is about 1.9 times larger than that without trapezoid rods.

• Journal of Advanced Marine Engineering and Technology
• /
• 제32권5호
• /
• pp.691-697
• /
• 2008

Heat exchangers are commonly used in practice in a wide range of application, from heat and air-conditioning system in a household, to chemical processing and power production in large plant. An Experimental study was conducted to investigated the fluid flow and heat transfer around four circular cylinders of in-line in a cross flow of air. The local and average heat transfer characteristics for tube banks are investigated in the present study. Heat transfer in a heat exchanger usually involves convection in each fluid and conduction through the wall separating the two fluid. The in-line pitch ratio was in the range $1.5{\leq}L/d{\leq}4.0$, where L is the center distance and d the cylinder diameter, and in the Reynolds number $8,000{\leq}Re{\leq}50,000$. The local and mean Nusselt numbers were estimated. Subsequently, the heat transfer characteristics of four circular cylinders are found to exhibit a strong dependency upon the separation point of their upstream cylinders.