• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.11
• /
• pp.806-809
• /
• 2013

In this study, $(Na_{0.525}K_{0.443}Li_{0.037})(Nb_{0.883}Sb_{0.08}Ta_{0.037})O_3+0.10\;wt%Bi_2O_3+0.35\;wt%B_2O_3$ ceramics were prepared by conventional soild-state sintering process. The specimens were sintered at temperature range from $1,060^{\circ}C$ to $1,100^{\circ}C$. XRD (X-ray diffractron), SEM (scanning electron microscope) were used to analyze the crystal structure and microstructural sproperties of specimens. And also, $T_{O-T}$, TC were observed by the mesurement of temperature dependence of dielectric constant. Excellect physical properties of the piezoelectric constant $d_{33}$= 170 pC/N, electromechanical coupling factor kp= 0.312, Tc= $315^{\circ}C$ were obtained, respectively, from the specimen sintered at $1,080^{\circ}C$.

• Polymer(Korea)
• /
• v.26 no.1
• /
• pp.113-120
• /
• 2002

Electrostriction is the phenomenon that a material is strained due to Maxwell stress developed by the applied voltage. In many electrostrictive materials, especially polymeric elastomers can produce large deformation and force due to their low elastic modulus. In this study, polyurethanes and acrylic rubber with compliant electrodes were used as electrostrictive polymer(EP) actuator. Actuation characteristics of the EP actuators with different physical properties of dynamic modulus and dynamic dielectiric constant were analyzed under AC field. The classical laminate theory was also used to simulate the actuation process in relation to the geometry and the physical properties of the actuators.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2003.10a
• /
• pp.119-119
• /
• 2003

Plasma polymerized organic thin films were deposited on Si(100) glass and Copper substrates at 25 ∼ 100 $^{\circ}C$ using cyclohexane and ethylcyclohexane precursors by PECVD method. In order to compare physical and electrochemical properties of the as-grown thin films, the effects of the RF plasma power in the range of 20∼50 W and deposition temperature on both corrosion protection efficiency and physical properties were studied. We found that the corrosion protection efficiency (P$\_$k/), which is one of the important factors for corrosion protection in the interlayer dielectrics of microelectronic devices application, was increased with increasing RF power. The highest P$\_$k/ value of plasma polymerized ethylcyclohexane film (92.1% at 50 W) was higher than that of the plasma polymerized cyclohexane film (85.26% at 50 W), indicating inhibition of oxygen reduction. Impedance analyzer was utilized for the determination of I-V curve for leakage current density and C-V for dielectric constants. To obtain C-V curve, we used a MIM structure of metal(Al)-insulator(plasma polymerized thin film)-metal(Pt) structure. Al as the electrode was evaporated on the ethylcyclohexane films that grew on Pt coated silicon substrates, and the dielectric constants of the as-grown films were then calculated from C-V data measured at 1㎒. From the electrical property measurements such as I-V ana C-V characteristics, the minimum dielectric constant and the best leakage current of ethylcyclohexane thin films were obtained to be about 3.11 and 5 ${\times}$ 10$\^$-12/ A/$\textrm{cm}^2$ and cyclohexane thin films were obtained to be about 2.3 and 8 ${\times}$ 10$\^$-12/ A/$\textrm{cm}^2$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.252-255
• /
• 1999

The effect of calcination temperature(1st and 2nd calcining at 110$0^{\circ}C$ , 120$0^{\circ}C$ and 130$0^{\circ}C$ respectively) on physical properties of BMNT Ceramics ware investigated. The optimum 1st and 2nd calcination temperature were 120$0^{\circ}C$ , and sintering temperature was 155$0^{\circ}C$. In this condition, the sintering density was 7.53 [g/㎤] and the dielectric constant, Q.f$_{0}$ and $\tau$$_{r}$ were 26, 80, 300[GHz] and +1.5[ppm/$^{\circ}C$] respectively in the microwave range.e.e.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.2
• /
• pp.820-829
• /
• 2017

Vegetable oil dielectrics have been used in transformers as green alternatives to mineral insulating oils for about twenty years, because of their advantages of non-toxic, biodegradability, and renewability. However, the viscosity of vegetable oils is more than 3 times of mineral oils, which means a poor heat dissipation capacity. To get low-viscosity dielectrics, transesterification and purification were performed to prepare vegetable oil methyl esters in this study. Electrical and physical properties were determined to investigate their potential as dielectrics. The results showed that the methyl ester products had good dielectric strengths, high water saturation and enough fire resistance. The viscosities (at $40^{\circ}C$) were 0.2 times less than FR3 fluid, and 0.7 times less than mineral oil, which indicated superior cooling capacity as we expected. With the assistance of 0.5 wt% pour point depressants, canola oil methyl ester exhibited the lowest pour point ($-26^{\circ}C$) among the products which was lower than FR3 fluid ($-21^{\circ}C$) and 25# mineral oil ($-23^{\circ}C$). Thus, canola oil methyl ester was the best candidate as a low-viscosity vegetable oil-based dielectric. The low-viscosity fluid could extend the service life of transformers by its better cooling capacity compared with nature ester dielectrics.

• Carbon letters
• /
• v.26
• /
• pp.25-30
• /
• 2018

The dielectric medium used in electrophoretic displays (EPDs) is required to be an environmentally friendly solvent with high density, low viscosity, and a large electric constant. Hydrofluoroether, a highly fluorinated solvent with eco-friendly characteristics, is regarded as a viable alternative medium for EPDs, owing to the similarity of its physical properties to those of the conventional EPD medium. Surface modification of particles is required, however, in order for it to disperse in the charged solvent. Also, positive/negative charges should be present on the particle surface to enable electrophoretic behavior. In this study, carbon black particles wrapped with positively charged nitrogen (N-CBs) were fabricated by a simple hydrothermal process using a poly(diallyldimethylammonium chloride) solution as a black coloring agent for the EPD. The dispersion behavior of N-CBs was investigated in various solvents.

• Journal of the Korean Ceramic Society
• /
• v.16 no.2
• /
• pp.77-82
• /
• 1979

Diopside-Anorthite body was easily synthesized at relatively low temperature 1225℃, compared with the synthesizing temperature 1425℃ of Anorthite. Of Diopside-Anorthite body, the synthesizing temperature was considered to be higher than 1225℃ because Gehlenite, probably formed at 1220℃, was detected by X-ray diffraction. This body has excellent physical and electrical properties, i.e. electric resistivity (1.2×1014Ωcm), low dielectric constant (6.26) and low thermal expansion coeffcient (61.9×10-7/℃). It's hardness was good enough for electrical subsidiary. In addition, this body, Diopside-Anorthite, has exellent properties for heat resisting wares.

• Journal of the Korean Ceramic Society
• /
• v.26 no.4
• /
• pp.568-574
• /
• 1989

Effect of PbO addition on sintering and piezoelectric properties at 0.45Pb(Ni1/3Nb2/3)O3-0.40PbTiO3-0.15PbZrO3 composition which is tetragonal phase was investigated. In this composition, Porosity and dielectric constant were increased with excess PbO addition, but Kp and d31 was not changed. These variation of physical properties could be interpreted as composition change of solid grains from tetragonal to MPB region due to amount of PbO-rich liquid changing.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.32 no.1
• /
• pp.35-39
• /
• 2019

In this study, we investigated the optimum calcination temperature of lead-free $0.74(Bi_{0.5}Na_{0.5})TiO_3-0.26SrTiO_3$(BNST) piezoelectric ceramics by analyzing the crystal structure, dielectric properties, and electric field-induced strain behavior. BNST ceramics prepared by conventional solid-state reaction methods at various calcination temperatures according to the industrial standard. All samples of BNST ceramics were subsequently sintered at $1,175^{\circ}C$ for 2 h. Crystal structure classification of the ceramics showed a single perovskite phase, with no second phase detectable for the samples calcined at $750^{\circ}C$ or higher. BNST samples calcined at $850^{\circ}C$ exhibited the most optimal values for itsand the common physical parameters of $density=5.518g/cm^3$, ${\varepsilon}=1,871.837$, $tan{\delta}=0.047$, and ${d_{33}}^*=874pm/V$.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.48 no.6
• /
• pp.410-415
• /
• 1999

$Ba_{1-x}Sr_xTiO_3$ thin films with various ratio of Sr (X = 0.4, 0.5, 0.6) were grown $Pt/TiN/SiO_2/Si$ subastrate by RF magnetron sputtering deposition. As, Ag, and Cu films were deposited on $Ba_{1-x}Sr_xTiO_3$ thin films as top electrodes by using a thermal evaporator. The electrical properties of $Ba_{1-x}Sr_xTiO_3$ thin films for various compositions were characterized and the physical properties at interface between $Ba_{1-x}Sr_xTiO_3$ thin films and top electrodes were evaluated in terms of the work function difference. At x =0.5, the degradation of capacitance is lower to the other compositions. As negative biasapplied, the specimen with Cu top electrode has board saturation region and low leakage current since work function of Cu is bigger than other electrodes.$ Ba_{0.5}Sr_{0.5}TiO_3$ thin films with Cu top electrode, the dielectric constant was measured to the value of 354 at 1 kHz and the leakage current was obtained to the value of $5.26\times10^{-6}A/cm2$ at the forward bias of 2 V.