• 콘크리트학회논문집
• /
• 제11권4호
• /
• pp.147-156
• /
• 1999

Current design code states that the strength reduction factor shall be permitted to be increased linearly from that for axial compression to that for flexure as the design axial load strength $\Phi$cPn decrease from 0.1fckAg to zero. Since this empirically adopted axial load level of $\Phi$cPn=0.1fckAg considers only sectional area and concrete strength, the other variables such as steel ratio, steel yielding strength, and steel arrangement can not be considered. This research is performed to investigate the consistency and the rationality of the code requirement for determination of column design strength. A nonlinear axial force-moment-curvature analysis was conducted in order to investigate the ductility of reinforced concrete column sections. As the result of ductility analysis, it was found that the ductility at the axial force of $\Phi$cPn=0.1fckAg represented a lock of consistency for the various variable contained sections. Therefore, a more reasonable application method of strength reduction factor is proposed, that is based on the strain ductility index.

• 한국터널지하공간학회 논문집
• /
• 제12권2호
• /
• pp.129-144
• /
• 2010

원형수직터널에 작용하는 토압은 아칭효과로 인해 2차원 일반 흙막이벽에 작용하는 토압보다 작으므로 원형수직터널 설계 시 벽체에 작용하는 실질적인 토압의 예측이 필요하다. 본 논문은 두 개의 연속된 논문(Companion papers)의 두번째로서 원형수직터널 설계 시 건조한 사질토뿐만 아니라 c-$\phi$ 지반과 다층지반에서 적용 가능하도록 새롭게 제안된 토압식(김도훈 등, 2009)을 증명하기 위해 대형 모형실험을 수행하였다. 고안된 모형실험 장비는 단계별 굴착이 가능하도록 제작 벽체의 반경을 변화시켜가며 실험을 수행하였다. 또한 강사 방법으로 지반을 조성하기 전 건조한 시료에 물을 첨가하고 불포화사질토를 형성시켜 겉보기 점착력을 발현시킴으로써 c-$\phi$ 지반과 다층지반에서 실험을 진행하였다. 실험 결과로서, 단계별 굴착을 모사하였을 때, 아칭효과에 의해 굴착된 지반에서 굴착되지 않은 지반으로 하중이 전이가 일어나는 확인할 수 있었다. 또한, 동시에 굴착했을 때의 토압은 예측한 값에 비해 상당히 작게 나타났지만, 단계별로 굴착했을 때의 최종 토압은 동시 굴착 시의 토압에 비해 크게 나타나며 새롭게 제안된 토압식과 잘 일치하였고 c-$\phi$ 지반과 다층지반에서 수행한 실험의 결과도 겉보기 점착력의 효과로 인해 토압의 감소를 보이며 이론적인 값과 잘 일치하는 것으로 나타났다.

• 대한기계학회논문집B
• /
• 제26권4호
• /
• pp.561-569
• /
• 2002

This paper presents an investigation on $C_2$, CH, OH radicals and NOx emissions in partially premixed flames with acoustic excitation. The radicals are visualized by the digital image technique with optical filters and ICCD camera while NOx emissions are determined by a chemiluminescent detection(NOx analyser). The measurements are made in flames with an overall equivalence ratio (${\phi}_o$) 0.5 and a center tube equivalence ratio(${\phi}_c$) varing from 1.1 to 5.0 for a constant fuel flow rate. In the case of excitation, the visual shape of the flame is changed from laminar to turbulent-like flames. Images of $C_2$, CH, and OH radicals resemble those of the flame appearances as the excitation phase is varied, and the radicals generated at the upstream are convected toward the downstream. It is inferred that the flame characteristics is affected by the flow characteristics of air-fuel mixture. In the case of acoustic excitation, OH radicals are much increased relative to unexcitation. From the radicals and flame visualization under acoustic excitation, the reduction of flame length affects the shorter residence time of center tube mixture, and significantly influences the NOx reduction.

• 한국수산과학회지
• /
• 제36권1호
• /
• pp.49-54
• /
• 2003

새만금 갯벌의 입조조성 및 유기물질 분포 특성을 조사하기 위해 1999년 갯벌 91개를 채취하여 분석한 결과를 요약하면 다음과 같다. 입도의 특성을 보면 새만금 갯벌은 사질이 우세하였고, 세립한 제이차 혼합물인 실트질이 추가된 반면 Clay 함량은 매우 낮게 나타났다. 평균값의 범위는 $4.60\~10.90\;{\phi}$이었고 분급도 범위는 $-0.1\~1.75\;{\phi}$이었다. 그리고 왜도의 범위는 $-1.0\~0.92\;{\phi}$이었으며 첨도의 범위는 $0.27\~6.75\;{\phi}$를 보였다. 그러므로 새만금 방조제 공사에 의해 갯벌은 심한 변화 양상을 보이는 것을 알 수 있었다. 유기물질과 관련된 항목을 살펴보면, ORP의 범위는 -133$\~$200 mV로 평균 73 mV의 산화 상태를 나타내었지만 전체 91개 지점 중 24개 지점에서 환원상태를 나타내고 있었다 CODs의 농도범위는 $17.54\~6,176.25\;mg/kg$을 보였고 총탄소와 총황의 비 (S/C)는 0.02$\~$0.45 (평균0.24) 범위를 보였다. 그러므로 새만금 갯벌은 아직까지는 육상에서 유입되는 인위적인 유기 오염물의 영향을 비교적 적게 받는 것으로 사료되었다. 이상의 결과를 보면 새만금 갯벌은 사질이며 육상에서 유입되는 유기물 오염이 낮아 수산생물 생육 장소로 적합하므로 계속 보존하는 것이 좋을 것으로 생각되며 앞으로도 지속적인 조사연구가 이루어져야 한다.

• 원예과학기술지
• /
• 제28권3호
• /
• pp.415-422
• /
• 2010

상추 2종, 쑥갓, 청경채, 엔디브, 그리고 치커리의 엽채류담액 수경 재배 시 높이 100mm, 직경 20, 25, 30mm의 원통형의 플라스틱 튜브를 이용하여 근권제한 처리를 한 후 생육과 식물영양소를 조사하였다. 근권제한은 용기 크기에 따라 엽채류의 지상부 생체중이 25-95% 범위에서 감소하였으며, 쑥갓과 청경채가 가장 영향을 많이 받았고 엔디브나 치커리는 적게 받았다. 건물률, C/N율 및 총비타민C와 총안토시아닌의 함량은 근권제한에 의해 증가하였다. 무기성분 중 P와 K함량은 근권제한에 의해 모든 작물에서 감소하였지만, Mg, Fe, Mn, Zn 등은 작물에 따라 차이가 있었다. 식물 영양적 가치를 증가시키고 생육 억제를 감소하기 위한 적절한 근권 용적은 엽채류 종류에 따라 달랐다. 치커리, 엔디브, 그리고 상추는 ${\Phi}25mm{\times}100mm$, 쑥갓과 청경채는 ${\Phi}30mm{\times}100mm$ 튜브 처리에서 각각 가장 좋은 결과를 보였다. 이상의 결과, 수경재배 시 원통형의 플라스틱 튜브를 이용한 근권제한 처리가 엽채류의 영양적 가치를 향상시킬 수 있다는 것을 시사하였다.

• 열처리공학회지
• /
• 제30권6호
• /
• pp.251-257
• /
• 2017

The effect of annealing temperature on the martensitic transformation behavior, tensile deformation chracteristics and shape recovery etc., has been studied in TiNi based shape memory ribbon fabricated by coldrolling of wire. TiNi based shape memory wire (${\phi}=500{\mu}m$) of which structure is intermetallic compound could be cold-rolled without process annealing up to the reduction rate in thickness of 50%, but a few cracks appear in cold-rolled ribbon in the reduction rate in thickness of 65%. The $B2{\rightarrow}R{\rightarrow}B19^{\prime}$ martensitic transformation or $B2{\rightarrow}B19^{\prime}$ martensitic transformation occurs in annealing conditions dissipating lattice defects introduced by coldrolling. However, in case of higher reduction rate or lower annealing temperature, martensitic transformation in cold-rolled and then annealed ribbons does not occur. The maximum shape recovery rate of cold-rolled ribbons with the reduction rate of 35 and 65% could be achieved at annealing temperatures of 250 and $350^{\circ}C$, respectively. The shape recovery rate seems to be related to the stress level of plateau region on stress-strain curve.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 추계학술대회 논문집
• /
• pp.131-131
• /
• 2009

This paper describes the fabrication and characteristics of polycrystalline (poly) 3C-SiC microresonators with $3{\times}10^{17}{\sim}1{\times}10^{19}cm^{-3}$ in-situ N-doping concentrations. In this work, the crystallinity, carrier concentration and surface morphology of the grown thin films were evaluated by X-ray diffraction (XRD), scanning electron microscopy (SEM) and atomic force microscopy (AFM). The 1.2 ${\mu}m$ thick cantilvers and the 0.4 ${\mu}m$ thick doubly-clamped beam microresonators with various lengths were implemented using in-situ doping poly 3C-SiC thin films. The characteristics of the poly 3C-SiC microresonators were evaluated using quartz and a laser vibrometer under vacuum at room temperature. The resonant frequencies of the SiC microresonators decreased with doping concentrations owing to the reduction of the Young's modulus of the poly 3C-SiC thin films. It was confirmed that the resonant frequencies of the poly 3C-SiC microresonators are controllable by adjusting the doping concentrations.

• 열처리공학회지
• /
• 제25권4호
• /
• pp.196-205
• /
• 2012

The purpose of this study is to enhance the hardenability and the mechanical properties by the addition of alloying elements such as Ni, Cr, Mo and B for the development of Cr-Mo plastic mold steel with uniform hardness and microstructure. The ingots were prepared by vacuum induction melting and forged to ${\Phi}35mm$ round bar. Forged bars were quenched and tempered at $200{\sim}600^{\circ}C$ for 1.5 hour. Jominy test, boron distribution observation, microstructual observation, tensile test and charpy impact test were conducted. It was confirmed that the hardenablity of these steels was improved by increasing of alloying elements and further promoted by the addition of boron. The critical rate of cooling required to obtain the bainitic structure for 0.27C-1.23Cr-0.28Mo-B steel was $0.5^{\circ}C/sec$. Hardness and strength of Cr-Mo steels decreased with increasing tempering temperature, but elongation and reduction of area increased with increasing tempering temperature. However, impact energy tempered at $400^{\circ}C$ showed the lowest value in the range $200{\sim}600^{\circ}C$ due to the temper embrittlement.

• Structural Engineering and Mechanics
• /
• 제17권2호
• /
• pp.167-186
• /
• 2004

The design load-carrying capacities of wooden shores depend on factors, such as the wood species and properties, and construction methods. This paper focuses on the construction methods, including an upright single shore, group of upright shores, group of inclined shores, butt connections and lap connections. This paper reports experiments to obtain critical loads and then developed an empirical equation based on Euler' formula for the critical loads and design load-carrying capacities. The test results show that the critical loads for an upright single wooden shore are greater than the average values for a group of upright shores, and the latter are greater than the average values for a group of inclined shores. Test results also show that the critical loads become smaller when butt or lap connections are used, butt connections possessing greater critical loads than lap connections. Groups of inclined shores are very popular at work sites because they have some practical advantages even though they actually possess inferior critical loads. This paper presents an improved setup for constructing groups of inclined shores. With this method, the inclined shores have larger critical loads than upright shores. The design load-carrying capacities were obtained by multiplying the average critical loads by a resistance factor (or strength reduction factor, ${\phi}$) that were all smaller than 1. This article preliminarily suggests ${\phi}$ factors based on the test results for the reference of engineers or specification committees.

• Journal of Advanced Marine Engineering and Technology
• /
• 제25권3호
• /
• pp.617-622
• /
• 2001

The purpose of this study is to design and the analyze the stress of composited shaft which is wound by filament winding method. The composites shaft has high strength and reduction in weight compared to metal shaft. The classical laminate plate theory(CLT) was used fro analysis the stress, and for structure design. In order to replace metal shaft by composites shaft, the diameter of shaft was determined to $\phi$ 40. The ration of diameter was determined to 0.4 for torsional moment with CLT. In this result of analyzing the stress, composites shaft was safe $30^{\circ}~60^{\circ}$C of winding angle, and was fractured on $90^{\circ}$.