• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• 제5B권4호
• /
• pp.312-316
• /
• 2005

The single phase induction motor has been commonly applied to small-sized electrical appliances because of its low cost, but it has low efficiency and large torque ripple, and it is incapable of speed control. However, two-phase induction motors have small torque ripple, high efficiency and variable speed control, because they are inverter fed. In this paper, the dynamic characteristics of the two-phase induction motor, such as the torque ripple, current and speed, are analyzed by using the time-stepping finite element method, and compared with the cage-type single phase induction motor.

• 한국정밀공학회지
• /
• 제19권9호
• /
• pp.172-178
• /
• 2002

One of the ever-increasing demands on the performances of heterodyne interferometers is to improve the measurement resolution, of which current state -of-the-art reaches the region of sub-nanometers. So far, the demand has been met by increasing the clock speed that drives the electronics involved fur the phase measurement of the Doppler shift, but its further advance is being hampered by the technological limit of modem electronics. To cope with the problem, in this investigation, we propose a new scheme of phase -measuring electronics that reduces the measurement resolution without further increase in clock speed. Our scheme adopts a super-heterodyne technique that lowers the original beat frequency to a level of 1 MHz by mixing it with a stable reference signal generated from a special phase- locked-loop. The technique enables us to measure the phase of Doppler shift with a resolution of 1.58 nanometer at a sampling rate of 1 MHz. To avoid the undesirable decrease in the maximum measurable speed caused by the lowered beat frequency, a special form of frequency up-down counting technique is combined with the super-heterodyning. This allows performing required phase unwrapping simply by using programmable digital gates without 2n ambiguities up to the maximum velocity guaranteed by the original beat frequency.

• 한국운동역학회지
• /
• 제28권2호
• /
• pp.93-100
• /
• 2018

Objective: The purpose of this study is to analyze the kinematic characteristics of the national speed skaters in the curve phase of 500-m race. Method: Seven national skaters participated in the study. Race images were acquired using a high - speed camera, and the three-dimensional motion was analyzed. Results: For skaters, whose average velocity in the curve phase is high, the velocity of entry into the straight phase was also fast. The fast skaters showed a larger maximum angle of extension of the knee joints than the relatively slow skaters, and the trunk ROM was smaller. Fast skaters tended to match the timing of the movement of the lower limb with the pelvis, while slow skaters tended to rotate the left pelvis backward. The velocity of the curve phase did not show a clear relationship with stroke time, average trunk angle, and lap time. Conclusion: It is important to skate close to the inner line, keep the trunk ROM below 10 degrees, extend the knee angle to over 160 degrees, and match the movement of the pelvis and lower limb to accelerate in the curve phase. The average velocity of the curves was fast for many athletes, but the competition rankings were low. Therefore, it is possible to improve the performance by optimizing the start technique, the running characteristics of the straight phase, and the physical factors.

• 대한물리의학회지
• /
• 제15권4호
• /
• pp.67-74
• /
• 2020

PURPOSE: The progression of the center of pressure (COP) velocity of the stance phase may have important roles for predicting gait speed in older adults with cognitive decline. This study was conducted to identify the correlation between gait speed and the velocity of COP progression during the stance phase in older adults with cognitive decline. METHODS: Forty adults aged 65 years or older (twenty participants without cognitive decline, 20 participants with cognitive decline) were recruited. The COP progression velocity was measured using an F-scan pressure-sensitive insole system. The stance phase was divided into four sub-stages. (loading response, mid-stance, terminal stance, and pre-swing). Gait speed, double support phase, and cadence were also measured. Correlations and multiple regression analyses were performed. RESULTS: Gait speed was associated with the COP progression velocity in midstance (r = .719, p < .05), cadence (r = .719, p < .05) and the COP progression velocity in loading response velocity (r = .515, p < .05) in older adults with cognitive decline. However, no correlation was found in older adults without cognitive decline. In multiple regression analysis using gait speed as a dependent variable, the COP progression velocity in midstance and cadence were significant predictors of gait speed, with the COP progression velocity being the most significant predictor. CONCLUSION: The COP progression velocity is an important factor for predicting gait speed in older adults with cognitive decline, suggesting that the cognitive function influences gait speed and the velocity of COP progression.

• 전력전자학회논문지
• /
• 제17권3호
• /
• pp.238-245
• /
• 2012

This paper presents a sensorless speed control of a 2-phase switch reluctance motor(SRM). The proposed sensorless control scheme is based on the slide mode observer with parameter compensator to improve the estimation performance. In the stand still position, the initial rotor position is determined by pulse current responses of each phase windings and the current difference. In order to determine an accurate initial rotor position, the two initial rotor positions are estimated by the difference of the pulse currents. From the stand still to the operating region, a simple open loop control which determines the commutation sequence by the pulse current of the unexcited phase winding is used. When the motor speed is reached to the sensorless control region, the estimated rotor position and speed by the slide mode observer are used to control the SRM. The flux calculator used in the slide mode observer is designed by phase voltage and the voltage drops in the phase resistance of the winding. The accuracy of the flux calculator is dependent on the phase resistance. For the continuous update of the phase resistance, current gradient at the inductance break point is used in this paper. The error of the estimated rotor position at the current gradient position is used to update the phase resistance to improve the sensorless scheme. The proposed sensorless speed control scheme is verified with a practical compressor used in home appliances. And the results show the effectiveness of the proposed control scheme.

• 한국전자파학회논문지
• /
• 제14권8호
• /
• pp.809-815
• /
• 2003

OFDM/FH 시스템 등 고속 호핑을 요구하는 통신 시스템에서는 빠른 스위칭 속도와 낮은 위상잡음을 갖는 주파수 합성기가 필요하다. 본 논문에서는 기존의 PLL 주파수 합성기와 DH-PLL 주파수 합성기의 위상잡음과 스위칭 속도를 비교하고, OFDM/FH 시스템에 미치는 영향을 분석하였다. DH-PLL 주파수 합성기는 기존의 PLL 주파수 합성기에 비해 회로의 복잡도와 많은 전력 소모를 갖지만, 빠른 스위칭 속도를 갖고 있다. 일정한 루프필터 대역 하에서 위상잡음과 스위칭 속도가 반비례 관계를 갖고 있는 기존의 PLL 주파수 합성기와는 달리 DH-PLL 주파수 합성기는 매우 빠른 스위칭 속도와 낮은 위상잡음을 동시에 얻을 수 있다. 결과적으로 동일한 호핑 속도 요구를 만족해야 하는 경우 DH-PLL 주파수 합성기는 기존의 PLL 주파수 합성기보다 더 빠른 스위칭 속도와 더 적은 SNS손실을 얻을 수 있어 OFDM/FH 시스템 성능을 향상시킬 수 있다.

• Membrane and Water Treatment
• /
• 제3권4호
• /
• pp.243-252
• /
• 2012

Tri-n-butyl phosphate (TBP) was used as carrier for the transport of Golden yellow and Cibacron LSG dyes through a hexane bulk liquid membrane. The transport efficiency of dyes by TBP was investigated under various experimental conditions such as pH of the feed phase (dyes solution), concentration of the receiving phase (NaOH solution), concentration of TBP in membrane, rate of stirring, effect of transport time, type of solvent, dye concentration in feed phase, effect of temperature.. The maximum transport dyes occurs at ratio of 1:1 TBP-hexane At pH 3.0 0.1 (feed phase) the transport dyes decreased. At high stirring speed (300 rpm) the dyes transport from the feed phase to the strip phase was completed within 60 minutes at $27^{\circ}C$. Under optimum conditions: Feed phase 100 mg/L dyes solution at pH 1.0 0.1, receiving phase 0.1 mol/L NaOH solution, membrane phase 1:1 TBP-hexane , Stirring speed 300 rpm and temperature $27^{\circ}C$, the proposed liquid membrane was applied to recover the textile effluent.

• Journal of Power Electronics
• /
• 제19권3호
• /
• pp.761-770
• /
• 2019

This paper proposes a hybrid phase windings excitation method for improving the efficiency of a 7-phase brushless DC (BLDC) motor in the electric propulsion system of a ship. The electrical losses of a BLDC motor system depend on the operating region and the number of excited phase windings (2-phase, 4-phase or general 6-phase windings). In this paper the operating region and torque/speed characteristics according to the motor rotation speed and propeller load are analyzed for a number of excitation methods. In addition, it analyzes the electrical losses of the system under each of the excitation methods in the entire operating region of the motor. In every sampling time, the proposed control method calculates the electrical loss of the system for each of the excitation methods and operates a 7-phase BLDC motor by selecting the excitation method that results a decreased electrical loss at the operating speed. The usefulness of the proposed control algorithm is verified through experimental results.

• International Journal of Precision Engineering and Manufacturing
• /
• 제7권3호
• /
• pp.47-50
• /
• 2006

High-speed machining is a very useful tool and one of the most effective rapid manufacturing processes. This study sought to produce various high-speed machining materials with excellent quality and dimensional accuracy. However, high-speed machining is not suitable for microscale thin-walled structures because the structure stiffness lacks the ability to resist the cutting force. This paper proposes a new method that is able to rapidly produce very thin-walled structures. This method consists of high-speed machining followed by filling. A strong work-holding force results from the solidification of the filling materials. Low-melting point metal alloys are used to minimize the thermal effects during phase changes and to hold the arbitrarily shaped thin-walled structures quickly during the high-speed machining. We demonstrate some applications, such as thin-walled cylinders and hemispherical shells, to verify the usefulness of this method and compare the analyzed dimensional accuracy of typical parts of the structures.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1994년도 하계학술대회 논문집 A
• /
• pp.328-330
• /
• 1994

The Ultrasonic motor(USM) has many good characteristics such as high torque at low speed range, large holding torque based upon frictional force, high speed response, flexible free ferns, compactness in size, low magnetic noise and silentness in motion. Because of having low speed rotation, USM is good as an actuator of a small size direct drive (DD) manipulator. The acturators for the DD manipulators must have good controllability on the speed and torque from zero to maximum value continuously. New method was developed for speed and torque control by the phase difference control of the two-phase driving signals of the motor. Then rule adjustable compliant and dumped motion was realized on the output shaft of the motor by PD control of the output shaft angle.