• 한국가시화정보학회:학술대회논문집
• /
• 한국가시화정보학회 2002년도 추계학술대회 논문집
• /
• pp.109-112
• /
• 2002

The supersonic jet discharging from a petal nozzle is known to enhance mixing effect with the surrounding gas because it produces strong longitudinal vortices due to the velocity difference from both the major and minor axes of petal nozzle. In the present study, the supersonic free jet discharging from the petal nozzle is investigated experimentally. The nozzles used are 4, 6, and 8 lobed petal nozzles with a design Mach number of 1.7, and the flow fields are compared with a circular nozzle with the same design Mach number. The pitot impact pressures are measured using a fine pilot probe. The flow fields are visualized using a Schlieren optical method. The results show that the petal nozzle has more increased supersonic length compared with the circular jet.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.2133-2138
• /
• 2003

In general, flow entrainment of surrounding gas into a supersonic jet is caused by the pressure drop inside the jet and the shear actions between the jet and the surrounding gas. In the recent industrial applications, like supersonic ejector system or scramjet engine, the rapid mixing of two different gases is important in that it determines the whole performance of the flow system. However, the mixing performance of the conventional circular jet is very low because the shear actions are not enough. The supersonic jet discharging from a petal nozzle is known to enhance mixing effects with the surrounding gas because it produces strong longitudinal vortices due to the velocity differences from both the major and minor axes of petal nozzle. This study aims to enhance the mixing performance of the jet with surrounding gas by using the lobed petal nozzle. The jet flows from the petal nozzle are compared with those from the conventional circular nozzle. The petal nozzles employed are 4, 6, and 8 lobed shapes with a design Mach number of 1.7 each, and the circular nozzle has the same design Mach number. The pitot impact pressures are measured in detail to specify the jet flows. For flow visualization, the schlieren optical method is used. The experimental results reveal that the petal nozzle reduces the supersonic length of the supersonic jet, and leads to the improved mixing performance compared with the conventional circular jet.

• 한국환경농학회지
• /
• 제39권4호
• /
• pp.360-367
• /
• 2020

BACKGROUND: The productivity and quality of blueberry (Vaccinium ashei Reade) greatly depend on the number of fruits in a plant. Especially, fruit set more than appropriate number negatively affects productivity and marketability due to the increased number of small fruits and delayed harvest time. This study was conducted to investigate proper timing and concentration for applying chemical blossom thinners such as ammonium thiosulfate (ATS) and UREA. METHODS AND RESULTS: ATS at 1.25% and 1.50%, and UREA at 6% and 8% were applied in four developmental stages, bud swell, pink bud, full bloom and petal fall. Fruit thinning rate was calculated based on the number of fruits harvested divided by that of flowers before applying blossom thinners. Ratios of leaf to flower and leaf to fruit were calculated based on the number of fully developed leaves in 25 days after full blossom divided by that of flowers or fruits, respectively. Chemical injury of leaves was investigated by calculating the number of leaves with chemical injury divided by the total number of leaves. Fruit thinning rates were 48% and 66% for UREA treatments at 6% and 8%, respectively, and 49% and 62% for ATS treatments at 1.25% and 1.50%, respectively, in the full bloom stage. In the petal fall stage, fruit thinning rates were 18% and 24% for UREA treatments at 6% and 8%, respectively, and 49% and 35% for ATS treatments at 1.25% and 1.50%, respectively. Leaf to fruit ratio (L/FR) increased by 109% and 188% compared to leaf to flower ratio in ATS treatments at 1.25% and 1.50%, respectively, and L/FR increased 93 and 196% in UREA treatments at 6% and 8%, respectively, in the full bloom stage. In the petal fall stage, leaf to fruit ratio increased by 60% to 100% in ATS treatments, but did not significantly differ from the control in UREA treatments. Fruit harvest was delayed in all treatments of all developmental stages except for 1.5% ATS and 6% UREA treatments at the petal fall stage, whose fruit harvest was two or three days faster than the control. CONCLUSION: The application of ATS and UREA for blossom thinning should be in the petal fall and full bloom stages for early and late harvest, respectively. Considering chemical injury, integrated harvesting and fruit size, however, it is appropriate to apply ATS at 1.5% in the petal fall stage to increase fruit productivity and quality in blueberry.

• 원예과학기술지
• /
• 제29권5호
• /
• pp.456-460
• /
• 2011

이 연구는 장미(Rosa hybrida Hort.) '카디날'에 감마선을 조사하여 얻어진 변이의 발생 양상을 구명하고 변이의 특성을 평가하기 위해 실시하였다. 2002년 44주의 삽목묘에 $^{60}Co$ 선원으로부터 70Gy 선량의 감마선을 처리하여 포장에 심어서 2002년부터 2004년에 걸쳐 화색변이 발생을 관찰하였다. 4가지 화색 돌연변이체를 발견하여 2004년부터 2008년까지 재배하면서 이들 변이체가 완전변이체로 고정된 것을 확인하였다. 각 계통별 삽목.증식한 묘를 2008-2009년까지 농가에서 수경재배하여 특성을 조사하였다. 원래 '카디날'은 화색이 짙은 적색(Red group, 44A, 45B)인데 이로부터 발생한 4가지 변이체들 중, KA1은 연분홍(Red group, 55B-55D), KA2(Fig. 1C)는 분홍색(Red group, 63A-63B), KA3(Fig. 1D)는 KA2와 비슷하나 진분홍색이었고(Red purple group, N57A-N57C), KA4(Fig. 1E)는 주황색(Red group, 43A-43B)이었다. 꽃의 직경에서 원품종 '카디날'은 12.5cm인데 비해 'KA1'은 9.2cm로 작고, KA2는 12.9cm로 커서 서로간에 차이가 있었다. 꽃잎 수는 '카디날'이 35.5장인데 비해 KA2는 39.8장으로 가장 많았고, KA1은 가장 적었다. CIE Lab 값에서 변이체들은 L(명도)은 모두 높아지고 a와 b값은 KA4를 제외하고 낮아진 것으로 나타났다. 신초와 잎의 특성도 원품종 '카디날'과 '카디날'의 4가지 변이체 사이 차이가 있었다. KA1은 신초장, 절간장, 화경장, 가시발생 등에 가장 작았고 나머지 계통들은 대부분 '카디날'과 비슷하였다. 잎의 뒷면의 색은 꽃색이 적색인 '카디날'과 주황색 변이체 'KA4'에서 연한 적색을 띠었으나, KA1, KA2, KA3는 녹색이었다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.2145-2150
• /
• 2003

Ejector system is one of fluid machinery which can entrain the fluid in low pressure part and transport it to the higher pressure part. The ejector system has been widely used for the purpose of obtaining high-vacuum state, fluid transport, thrust augmentation, etc. It can transport a large capacity of fluid with relatively small device of no any moving parts, and thus seldom causes mechanical troubles. However, the conventional ejector system has been pointed out that its overall efficiency is quite low compared with other fluid machinery since it is derived by only the pure shear stresses. In the present study, 4, 6, and 8 lobed petal nozzles with a design Mach number of 1.7 are adopted as a primary nozzle to improve the ejector performance, and are compared with a conventional circular nozzle. The static pressures along the diffuser wall are measured to qualify the flow field inside the supersonic petal ejector system.

• 한국작물학회지
• /
• 제51권spc1호
• /
• pp.255-258
• /
• 2006

홍화 재배시 종실의 수량 감소가 적으면서 꽃잎 수량을 증가시키기 위해 밀식과 적심을 통하여 시험한 결과를 요약하면 아래와 같다. 개화기는 관행이 6월 23일인데 비해 적심 처리구는 2일 늦은 6월 25일에 개화하였으며 밀식처리구는 같았다. 유효분지수는 2열 밀식재배와 3열 밀식재배가 적심이나 대조구에 비해 많았으며, 유효화두수는 3열밀식재배에서 270개/$m^2$로 가장 많았으나 적심은 $186{\sim}223$개/로 적었다. 종실 수량은 대조구 10a당 220 kg에 비해 2열밀식재배는 231 kg으로 5% 증수 되었다. 채화 화두수는 3열밀식이 가장 많았으나 건조된 꽃잎 수량은 2열밀식과 3열밀식이 10a당 25.4 kg, 26.9 kg으로 대조구의 22.0 kg에 비해 각각 15%, 22% 증수되었다.

• 소성∙가공
• /
• 제10권6호
• /
• pp.465-470
• /
• 2001

Hole flanging experiments are performed on flat circular plates with a hole in the center and the flangeability and fracture behaviors of TRIP steels and ferrite-Bainite duplex steels were examined. In the hole flanging, deformation by lip and petalling occurs when plates are struck by punches of various shapes and high circumferential strains induced in the target material cause radial cracking and the subsequent rotation of the affected plate material in a number of symmetric petals. In all cases, failure of the plate was due to lip fracture that results from multiple localized neckings that take place around the hole periphery where straining is most severe and a somewhat regular pattern was observed in a fracture shape. The neck characteristics in flange formation and the transition from the lip to petal mode at which fracture occurs were compared with two materials.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2003년도 제20회 춘계학술대회 논문집
• /
• pp.19-22
• /
• 2003

이젝터-디퓨저 시스템은 일종의 유체기계로서, 저압부의 유체를 혼입하여 고압부로 이송한다. 기존의 이젝터-디퓨저 시스템은 유체의 순수한 전단력만을 이용하므로 다른 유체기계에 비하여 효율이 낮은 단점이 있다. 본 연구에서는 이젝터-디퓨저 시스템의 효율을 높이기 위하여, 설계마하수가 M$_{d}$=1.7이고 로브의 개수가 각각 4, 6, 8개인 페탈노즐을 구동노즐로 사용하였고, 원형구동노즐을 사용한 이젝터-디퓨저 시스템의 결과와 비교하였다.

• The Plant Pathology Journal
• /
• 제32권2호
• /
• pp.77-84
• /
• 2016

X-ray irradiation with convergent chemicals such as nano-silver particles or sodium dichloroisocyanurate (NaDCC) has been used to control leaf blight on cut lilies. The oriental hybrid lily cultivars Siberia, Le Reve, and Sorbonne were irradiated five times by 200 Gy of X-rays in 2014. In 2015, Siberia and Sorbonne were irradiated three times by 150 Gy of X-rays. After artificial infection with Botrytis elliptica on the leaves and petals of cut lilies, this study used convergent chemical X-ray irradiation of 200 Gy or 150 Gy. Leaf and petal blight was measured in terms of incidence and severity at 8 days after infection using total 552 cuttings. Results indicate that the treatments of X-ray irradiation and NaDCC in 2014 and 2015 slightly decreased the severity of petal blight on Siberia and Sorbonne. However, the results were not significant and severity did not decrease as NaDCC concentration increased. Vase-life was observed separately after X-ray irradiation of 270 cut lilies in 2014 and 108 cut lilies in 2015. Chlorophyll content was not affected by either 200 Gy or 150 Gy of X-rays. The number of days of fully opened flowers at Siberia of 150 Gy and Le Revu of 200 Gy increased by 1-2 days. In addition, the relative fresh weights of the X-rayed flowers were 10% drier than the non-irradiated controls. Overall, leaf blight control by X-ray was inferior to the control by gamma rays, and petal color was bleached in Sorbonne and Le Reve cvs. by 150 Gy of X-rays.

• 한국응용곤충학회지
• /
• 제42권4호
• /
• pp.301-305
• /
• 2003

기주식물에 따른 꽃노랑총채벌레의 생태적 특성을 조사한 결과, 가지, 오이, 고추, 토마토의 잎과 꽃잎에서 꽃노랑총채벌레의 발육기간은 고추 잎에서 6.4일로 가장 길었고, 생존율도 고추 잎에서 67%로 가장 낮았다. 오이의 잎에서 암컷의 수명이 16일로 가장 길었고, 꽃잎에서는 8.1일로 가장 짧았다. 꽃노랑총채벌레 암컷 성충은 가지, 오이, 고추, 토마토 중 토마토 꽃잎을 가장 선호하는 것으로 나타났고, 가지 성묘의 잎 위치별 부화 유충수는 중위 잎에 가장 많았다. 가지의 잎과 꽃잎에 대한 꽃노랑총채벌레 암컷 성충의 서식 선호성은 꽃잎을 더 선호하였고, 4개 작물(가지, 오이, 고추, 토마토)중 꽃잎에 대한 서식 선호성은 고추에서 가장 높았다.