• International Journal of Highway Engineering
• /
• v.16 no.2
• /
• pp.91-98
• /
• 2014

PURPOSES : The objective of this study is to investigate the effect of asphalt and geotextile interlayer on the fracture behavior of unbonded concrete overlay through a laboratory composite beam test. METHODS : In order to evaluate the effect of interlayer materials on the fracture behavior of unbonded concrete overlay, a laboratory test of composite beam was conducted with different types of interlayer. The test results of the composite beam using two types of geotextile interlayer with different thicknesses were compared to the test results of the composite beam using the tradition type of asphalt interlayer. The unbonded concrete overlay on the existing concrete pavement without interlayer was set for the control condition. RESULTS AND CONCLUSION : Overall, the laboratory composite beam test results did show the effect of asphalt and geotextile interlayer on the fracture behavior of composite concrete beams. The three-layer geotextile interlayer and HMA layer both increase the peak load when the first macrocrack occurs in the top concrete beam, while the HMA interlayer causes the smallest load drop percentage after the first macrocrack. The three-layer geotextile did show better performance than the single-layer geotextile through the greater peak load and smaller load drop percentage. It indicates that the thickness of geotextile interlayer will affect the fracture behavior of unbonded concrete overlay and the thicker geotextile interlayer is recommended.

• International Journal of Highway Engineering
• /
• v.16 no.2
• /
• pp.19-24
• /
• 2014

PURPOSES : The study objective was to evaluate rheology and physical properties of SBS-modified warm-mix asphalt (WMA) binders in comparison with hot-mix asphalt (HMA) binders. METHODS : Four different SBS polymers were used to prepare polymer-modified asphalt (PMA) binders, and three different warm-mix additives (WAD) were used to prepare a total of 12 WMA PMA binders. The kinematic viscosity was measured at 115, $135^{\circ}C$. The PG was determined using DSR and BBR. The pass/fail (P/F) temperatures for high and low PG grading were evaluated for HMA PMA and WMA PMA binders. RESULTS : PG 76-22 binders could be prepared by modifying the base binder (PG 64-22) using 4.5 wt% of SBS. The kinematic viscosity (KV) of SBS PMA was increased by 3 times higher than that of base asphalt. The SBS PMA with WAD showed 10% lower KV than that of the normal SBS PMA at $115^{\circ}C$ The high P/F temperatures showed almost no difference between HMA PMA and WMA PMA binders. The high P/F temperature showed very high correlations with KV ($R^2$ > 0.97). The result of SBS modification caused increase of low P/F temperature by $2.7^{\circ}C$ on average. CONCLUSIONS : Since the PMA with WAD showed 10% lower KV than normal (HMA) PMA at $115^{\circ}C$, reducing PMA mixture temperature down to a WMA level was possible in this study. The higher KV binders showed the higher P/F temperature. There was almost no change in high P/F temperature due to the use of WAD. The SBS PMA, showing an increased low P/F temperature, might show somewhat poorer performance at low-temperature, even though the lower PG grade was staying at the same level, i.e., $-22^{\circ}C$.

• International journal of advanced smart convergence
• /
• v.4 no.1
• /
• pp.137-144
• /
• 2015

Development of the yarn sorting equipment (khonhook) by slide way due to the principle of engineering that cause of workers on the long of motion time. The data was collected from the weaving group Ban Nongkok village, Nakornratchasima Province, THAILAND. According to the study, the step of yarn sorting (konhook) was one of the steps that affect long of motion time. The problem was the inadequate capacity equipment. The objective of research was to study and develop the yarn sorting equipment (konhook). The fabric used in the study was 64 meters in length and 1 meter in width. Researchers studied the processes the yarn sorting (konhook) which it consists of seven sub steps, 1) the thread tube setting, 2) yarn bunching, 3) tying a knot at the end of yarn, 4) looping the yarn into a pillar, 5) sorting the yarn (konhook), 6) crossing pillars and 7) taking out the yarn. Researchers focused on studying yarn sorting process (konhook) by designing and creating a device for yarn sorting (konhook) for reducing yarn sorting (konhook) time by the original method performance indicators. The results found that the developed yarn sorting equipment (konhook) ) by slide way could reduce working time from 7.24 minutes to 6.08 minutes of the original equipment yarn sorting (konhook). This means it could make the process 16.02 % faster. This also helps reducing the distance of workers' movement from 2,234 meters to 8 meters. This is 99.64 % shorter.

• Journal of Institute of Control, Robotics and Systems
• /
• v.17 no.11
• /
• pp.1117-1124
• /
• 2011

An integrated fault detection and isolation method is proposed in this paper. The main objective of this paper is development fault detection, isolation and diagnosis algorithm based on the DKF (Decentralized Kalman Filter) and the bank of IMM (Interacting Multiple Model) filters using penalty scalar for both partial and total faults and the outlier detection algorithm for preventing false alarm also included. The proposed FDI (Fault Detection and Isolation) scheme is developed in four phases. In the first phase, the outlier detection filter is designed to prevent false alarm as a pre-filter. In the second phases, two local filters and master filter are designed to detect sensor faults. In the third phases, the proposed FDI scheme checks sensor residual to isolate sensor faults and 11 EKFs actuator fault models are designed to detect wherever actuator faults occur. In the last phases, four filters are designed to identify the fault type which is either the total fault or partial fault. The developed scheme can deal with not only sensor and actuator faults, but also preventing false alarm. An important feature of the proposed FDI scheme can decreases fault isolation time and figure out not only fault detection and isolation but also fault type identification. To verify the proposed FDI algorithm performance, the Simulator is also developed under the Matlab/Simulink environment.

• The Journal of Society for e-Business Studies
• /
• v.17 no.1
• /
• pp.189-214
• /
• 2012

In recent years, the innovative management tool of Business Process Management (BPM), has begun to reorganize business processes to enhance firms' operational performance. As practitioners have identified a number of failed BPM projects, research has begun to consider the Critical Success Factors (CSFs) for successful BPM implementation. However, these research works have not yet been properly theoretically grounded in being able rigorously to classify and then compare different BPM implementation practices. The main objective of this paper is thus to identify a theoretical basis for BPM implementation. The paper proposes a combined theoretical framework of dynamic capability and task-technology fit to identify CSFs for BPM. This basis is then used to interpret three different case studies of BPM implementation in Korea.

• The Journal of Society for e-Business Studies
• /
• v.17 no.1
• /
• pp.39-52
• /
• 2012

The introduction of iPhone was an opportunity to increase of internal smarphone users in 2009 and it exceeded 15 millions at August, 2011. According to report about usage of smartphone users, elderly people aged over 60 was quite low compared to other groups. Moreover these elderly peoples feel lag behind cause of smartphone non-use. Thus, the aim of this research is to improve usability of smartphone for elderly peoples. The performance evaluation program and questionnaire were developed for this purpose and objective data and subjective data were collected through these. 22 elderly peoples participated in our research and we could derived proper level of target. The results of this research will be applied to smartphone or application for elderly. The meaning of this research is reveal the detailed touch target for elderly based on smartphone environment.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.2
• /
• pp.312-320
• /
• 2012

In this study, we introduce a new design methodology of a granular-oriented self-organizing polynomial neural networks (GoSOPNNs) that is based on multi-layer perceptron with Context-based Polynomial Neurons (CPNs) or Polynomial Neurons (PNs). In contrast to the typical architectures encountered in polynomial neural networks (PNN), our main objective is to develop a methodological design strategy of GoSOPNNs as follows : (a) The 1st layer of the proposed network consists of Context-based Polynomial Neuron (CPN). In here, CPN is fully reflective of the structure encountered in numeric data which are granulated with the aid of Context-based Fuzzy C-Means (C-FCM) clustering method. The context-based clustering supporting the design of information granules is completed in the space of the input data while the build of the clusters is guided by a collection of some predefined fuzzy sets (so-called contexts) defined in the output space. (b) The proposed design procedure being applied at each layer of GoSOPNN leads to the selection of preferred nodes of the network (CPNs or PNs) whose local characteristics (such as the number of contexts, the number of clusters, a collection of the specific subset of input variables, and the order of the polynomial) can be easily adjusted. These options contribute to the flexibility as well as simplicity and compactness of the resulting architecture of the network. For the evaluation of performance of the proposed GoSOPNN network, we describe a detailed characteristic of the proposed model using a well-known learning machine data(Automobile Miles Per Gallon Data, Boston Housing Data, Medical Image System Data).

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.3
• /
• pp.331-337
• /
• 2012

In this study, the front side member is optimized using a topography optimization technique. Optimization of a simple beam is conducted before optimization of the front side member. The objective function is set to minimize the first buckling factor in the longitudinal direction. The design variable corresponds to the perturbation of nodes normal to the shell's mid-plane space. The crash analysis is conducted on a simple beam, which is optimized by Response Surface Method and the topography optimization technique. In order to verify the topography optimization technique, the results of the RSM and topography optimization model are compared. Consequently, we confirm the satisfactory performance of the topography optimization technique, and apply this topography optimization to the front side member. Thus, the front side member is optimized and its crashworthiness is increased.

• Journal of Korea Water Resources Association
• /
• v.45 no.2
• /
• pp.165-178
• /
• 2012

The objective of this study is to evaluate the applicability of Land Surface Model (LSM) for estimating the runoff on East Asia. Global geographical and weather data are used as input for the model and for the model verification, the simulated runoff results are compared with observed data from 34 global observation stations provided by Global Runoff Data Center (GRDC). K$\ddot{o}$ppen's climate zone is used to calculate the model parameter for ungaged basins. As a result, the simulated runoff shows good performance comparing with observed data in 17 basins assumed as ungaged basins. The Hydrologic components on East Asia area are estimated from the model and the continental water balance components are seasonally similar to each country. Also, it reveals that runoffs from southern China, Japan and Taiwan are much higher than those from mongolian and northern China.

• Journal of Institute of Control, Robotics and Systems
• /
• v.19 no.8
• /
• pp.709-717
• /
• 2013

This paper presents the development of a specialized underwater leg with a manipulator function(convertible-to-arm leg) for the seabed walking robot named CRABSTER200(CR200). The objective functions of the convertible-to-arm leg are to walk on the seabed and to work in underwater for precise seabed exploration and underwater tasks under coastal area with strong tidal current. In order to develop the leg, important design elements including the degree of freedom, dimensions, mass, motion range, joint structure/torque/angular-speed, pressure-resistance, watertight capability and cable protection are considered. The key elements of the convertible-to-arm leg are realized through concept/specific/mechanical design and implementation process with a suitable joint actuator/gear/controller selection procedure. In order to verify the performance of the manufactured convertible-to-arm leg, a 25bar pressure-resistant and watertight test using a high-pressure chamber and a joints operating test with posture control of the CR200 are performed. This paper describes the whole design, realization and verification process for implementation of the underwater convertible-to-arm leg.