• Korean Journal of Microbiology
• /
• v.9 no.2
• /
• pp.55-60
• /
• 1971

Among 50 yeasts of red pepper paste isolated and identified in the previous report, 12 strains of yeast which possess osmophilic and non-film characteristics were examined their growth rates and alcohol fermentation ability in red pepper medium. 5 strains of yeast possessing powerful growth rates and excellent alcohol fermentation ability were selected as excellent yeasts in this experiment. And their cultural conditions, salt resistance and red pepper concentration upon the growth were examined in this report. The results obtained were as follows ; 1) Among 12 strains of yeast, Saccharomyces cerevisiae group II(strain $D_1$), Saccharomyces oviformis($D_2$), Saccharomyces steineri($M_3$), Saccharomyces rouxii($D_9$) and Saccharomyces mellis($G_8$) were selected as excellent yeasts. 2) Among 5 strains of yeast selected, the strain $D_1$ and $D_2$showed the best alcohol fermentation ability and the best fermentative flavour. 3) The optimum temperature for growth of the strain $D_1$ and $D_2$ was $25^{\circ}C$$M_3$, $D_9$ and $G_8$ $30^{\circ}C$$D_1$ and $D_2$ was $62^{\circ}C$$M_3$,$D_9$ and $G_8$ ws 60.deg.C with treatment for 10 minutes. 4) The optimum pH for growth of all strains was around 5.0. 5) The strain $D_1$ and $M_3$were grown exceedingly well on the emdia containing 3 percent of NaCl and $D_2$,$D_9$ and $G_8$ on the media containing 6 percent of NaCl. 6) In the case of 5 percent of red pepper liquor added 5 percent of glucose was more nutritional than in the case of 5 percent glucose only. However, the growth rates of yeasts were restrained by the increase of red pepper concentration.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.5
• /
• pp.1193-1199
• /
• 1990

Effects of strain hardening exponents on the behavior of fatigue crack propagation are experimentally investigated. The retardation effect of fatigue crack propagation after single overloading is investigated in relation to strain hardening exponent and crack closure. A relationship between crack opening ratio and strain hardening exponents is inspected through an examination of the crack closure behavior. An empirical equation relating retardation effect of fatigue crack propagation after single overloading, percent peak load and strain hardening exponent of materials is proposed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.247-250
• /
• 1995

The development and empirical validation of a mathematical model for predicting the depth of deformed layer in a machined surface are presented. The main assumption for develioping this model is that there is a linear relationship between plastic strain and the depth to which it extends. The model relates the work required to shear the workpice material to the work needed to compress the workpiece material ahead of the cutting tool. The results show that the percent difference between the calculated and the measured depth of deformed layer ranges form 4 percent to 19 percent. An improvement of the model is suggested through application of actual distribution data of plastic strain.

• Journal of the Society of Naval Architects of Korea
• /
• v.48 no.2
• /
• pp.171-177
• /
• 2011

Tensile tests were conducted at low temperatures for the steel materials which are used for outer shell of the vessels making transit through the polar regions. The selected steel materials were GL-DH32, GL-DH36 and GL-EH36. In comparison with the results at room temperature, the yield stress increases approximately by 10 to 13 percent at $-30^{\circ}C$ and by 13 to 19 percent at $-50^{\circ}C$ while the tensile strength increases about by 9 percent at $-30^{\circ}C$ and 11 to 14 percent at $-50^{\circ}C$. To obtain true stress-true strain, i.e. correct plastic hardening characteristics, Bridgman's(1952) necking correction formula was introduced taking triaxial state of stresses after onset of diffuse necking into consideration. Photographs of fractured surfaces were taken by using Scanning Electron Microscope immedately after tensile tests completed and one for GL-EH36 has been presented in this paper.

• Journal of Welding and Joining
• /
• v.6 no.4
• /
• pp.16-26
• /
• 1988

The effect of carbon content on hot cracking of welded carbon steel was investigated Eight steel plates whose carbon content range from 0.02 to 0.23 percent were welded by autogeous gas tungsten are process. Constant strain was applied to the hot crack test specimen under the strain rate of 0.15 mm per second during welding. The hot cracking susceptibility ws high in the rnage of 0.02-0.05 and 0.12-0.23 percent carbon contents. The critical carbon content immune to hot cracking is in the range from 0.07 to 0.12 percent carbon. By electron probe microanalyser, amanganese segregation was not seen significantly in the whole carbon range. But segregation of silicon was higher in the region of low carbon contents. However, sulphur was segregated remarkably in the region betwen 0.18 and 0.23 percent carbon by peritectic reaction. Very smal lamount of dnedritic structure was observed in the region from 0.02 to 0.05 percent carbon by peritectic reaction. Very small amount of dendritic structure was observed in the region from 0.02 to 0.05 percent carbon but the predominant solidification structure was smooth by cellular growth. The higher the carbon content is, the more the columnar dendritic structure was observed.

• Structural Engineering and Mechanics
• /
• v.11 no.5
• /
• pp.565-574
• /
• 2001

Experimental investigation into the behaviour of half-scale brick masonry panels were conducted under cyclic loading normal to the bed joint and parallel to the bed joint. For each cycle, full reloading was performed with the cycle peaks coinciding approximately with the envelope curve. Unloading, however, was carried out fully to zero stress level and partially to two different stress levels of 25 percent and 50 percent of peak stress. Stability point limit exhibits a unique stress-strain curve for full unloading but it could not be established for partial unloading. Common point limit was established for all unloading-reloading patterns considered, but its location depends on the stress level at which unloading is carried to. Common point curves were found to follow an exponential formula, while residual strains versus envelope strains can be expressed by a polynomial function of a single term. The relation between residual strain and envelope strain can be used to determine the stress level at which deterioration due to cyclic loading began.

• Structural Engineering and Mechanics
• /
• v.11 no.3
• /
• pp.301-314
• /
• 2001

The purpose of this experimental study is to investigate the damage mechanism due to shear-fatigue behavior of high-strength reinforced concrete beams under repeated loading. The relationship between the number of cycles and the deflection or strain, the crack growths and modes of failure with the increase of number of cycles, fatigue strength, and S-N curve were observed through a fatigue test. Based on the fatigue test results, high-strength reinforced concrete beams failed at 57-66 percent of static ultimate strength for 2 million cycles. The fatigue strength at 2 million cycles from S-N curves was shown as about 60 percent of static ultimate strength. Compared to normal-strength reinforced concrete beams, fatigue capacity of high-strength reinforced concrete beams was similar to or lower than fatigue capacity of normal-strength reinforced concrete beams. Fatigue capacity of normal-strength reinforced concrete beams improved by over 60 percent.

• Geomechanics and Engineering
• /
• v.7 no.4
• /
• pp.431-458
• /
• 2014

Construction of a new cavern close to an existing cavern will result in a modification of the state of stresses in a zone around the existing cavern as interaction between the twin caverns takes place. Extensive plane strain finite difference analyses were carried out to examine the deformations induced by excavation of underground twin caverns. From the numerical results, a fairly simple nonparametric regression algorithm known as multivariate adaptive regression splines (MARS) has been used to relate the maximum key point displacement and the percent strain to various parameters including the rock quality, the cavern geometry and the in situ stress. Probabilistic assessments on the serviceability limit state of twin caverns can be performed using the First-order reliability spreadsheet method (FORM) based on the built MARS model. Parametric studies indicate that the probability of failure $P_f$ increases as the coefficient of variation of Q increases, and $P_f$ decreases with the widening of the pillar.

• Computers and Concrete
• /
• v.24 no.5
• /
• pp.445-452
• /
• 2019

In this paper, dynamic stress, strain and deflection analysis of concrete pipes conveying nanoparticles-water under the seismic load are studied. The pipe is buried in the soil which is modeled by spring and damper elements. The Navier-Stokes equation is used for obtaining the force induced by the fluid and the mixture rule is utilized for considering the effect of nanoparticles. Based on refined two variables shear deformation theory of shells, the pipe is simulated and the equations of motion are derived based on energy method. The Galerkin and Newmark methods are utilized for calculating the dynamic stress, strain and deflection of the concrete pipe. The influences of internal fluid, nanoparticles volume percent, soil medium and damping of it as well as length to diameter ratio of the pipe are shown on the dynamic stress, strain and displacement of the pipe. The results show that with enhancing the nanoparticles volume percent, the dynamic stress, strain and deflection decrease.

• Korean Journal of Soil Science and Fertilizer
• /
• v.29 no.2
• /
• pp.190-198
• /
• 1996

The Neomycin resistant gene in transposon 5 (Tn5) was introduced into a mutant of Bradyrhizobium japonicum RJB 6 $str^rnal^r$ by conjugation. This marked strain was used in coinoculation of soybean with Pseudomonas fluorescens(Ps-3) and Bacillus subtilis(BCAC-4) and in antibiotic treatment of soybean for studying rate of nodule formation and growth promoting effect on soybean plant. When the marked strain RJB 6 $str^rnal^rneo^r$ with Ps-3, BCAC-4, and Ps-3 plus BCAC-4 was coinoculated into two soils, the recovery rate of the marked strain was 8.5, 4.3 and 2.9 percent in soybean cultivated soil, and 10.3. 6.0 and 5.0 percent in soybean uncultivated soil. The best growth promoting effect of coinoculation on soybean plant was found with the marked strain plus Ps-3. When the marked strain was inoculated into soybean with antibiotic treatment, the rate of nodule formation in soybean cultivated soil was between 12.5 and 25.4 percent, while that in soybean uncultivated soil was between 23.7 and 43.2 percent. The highest rate of nodule formation with the marked strain was found in streptomycin 1000 ppm treatment plot.