• Journal of Mechanical Science and Technology
• /
• v.18 no.4
• /
• pp.640-648
• /
• 2004

This paper describes a new magnetization method for non-destructive testing with magneto-optical sensor (denoted as MO sensor) which have the following characteristic : high observation sensitivity, independence of the crack orientation, and precise imaging of a complex crack geometry such as multiple cracks. When a magnetic field is applied normally to the surface of a specimen which is significantly larger than its defects, approximately the same magnetic charge per unit area occurs on the surface of the specimen. If there is a crack in the specimen, magnetic charge per unit area has the same value at the bottom of the crack. The distribution of the vertical component of the magnetic flux density, B$\_$Z/, is almost uniform over the no-crack area (denoted as B$\_$Z,BASE/), while the magnetic flux density is smaller in the surroundings of the crack(denoted as B$\_$Z,CRACK/) If B$\_$Z, BASE/ is a bit larger than the saturated magnetic flux density of the MO sensor (B$\_$s/) , then small magnetic domains occur over the crack area and a large domain over the non-crack area because B$\_$Z,CRACK/ is smaller than B$\_$s/.

• Journal of Preventive Medicine and Public Health
• /
• v.15 no.1
• /
• pp.205-211
• /
• 1982

This survey was conducted to find out demage done to the farmers by Agrochemicals in a rural area of Korea from January to October, 1980. Choon Sung Gun, Kang Won Province was the survey area and the 412 males were surveyed among all those that have sprayed agrochemicals during 10 Months in 1980. Obtained results and findings from this survey are summarized as follows; 1. The total spray days of 413 males were 3,114 days and avarage spray days per person were 7.54 days. Also avarage spray hours per person were 4.7 hours. 2. The incidence rate per 100 persons of self-recognized skin manifestation was 12.6 persons and incidence rate per spray day was 2.7 percent. The incidence rate per 100 persons of self-recognized intoxication was 23.0 persons and incidence rate per spray day was 3.6 percent. 3. In cases where mask was not used, when it was syrayed in hot weather, when stronger solution was used, the results were higher percentage in self-recognized intoxication (P<0.01). 4. The symptoms of self-recognized intoxication were headache (55.8%), dizziness (46.9%), nausea (17.7%), fatigue (17.0%), and vomiting (17.0%), 5. Number of intoxication per 100 used standardized unit by agrochemicals was parathion (93.8 spells), sumithion (91.8 spells) and folithion (66.7 spells). 6. Treatment was done by health facility utilization (27 cases), visits to drug store (13 cases) and visits to health center (7 cases).

• Advances in nano research
• /
• v.8 no.3
• /
• pp.229-244
• /
• 2020

In this paper, modified Kelvin's model has been used to analyze the orthotropic vibration frequencies of single walled carbon nanotubes with clamped-clamped and clamped-free boundary conditions. For this system the governing equation is developed with wave propagation approach. Armchair, zigzag and chiral structures are considered for the vibrational analysis to investigate the effect of different modes, in-plane rigidity and mass density per unit lateral area. Throughout the computations, on decreasing the length-to-diameter ratios, the frequencies of said structure increases. In addition, by increasing three different value of in-plane rigidity resulting frequencies also increase and frequencies decrease on increasing mass density per unit lateral area. The results generated using computer software MATLAB to furnish the evidence regarding applicability of present model and also verified by available published literature.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.28 no.1
• /
• pp.43-50
• /
• 2010

The 200mesh screen was tensioned and fixed on a frame. When applied tension to 5N and 10N per unit area, a side length of opening of the screen was 163.223${\mu}m$ and 168.224${\mu}m$, respective. But side length not tensioned was 158.879${\mu}m$. We knew that a side length of opening of the screen rarely changes with tension applied to the screen. The appearances that a side length of opening of the screen expand little are due to a decreasing diameter of thread by means of tension. In a thickness measurement of screen, While the high density mesh screen that had a lot of knots that crossed a line of latitude and longitude per unit area appeared a higher numerical value, the low density mesh screen that had a few knots appeared a low numerical value.

• International Journal of Industrial Entomology and Biomaterials
• /
• v.7 no.1
• /
• pp.69-73
• /
• 2003

Specific leaf weight (SLW), defined as the mass of tissue per unit leaf area has been found to be an important physiological parameter as it indicates the relative thickness of leaves. Greater SLW provides more photosynthetic potential per unit area of leaf and hence it is frequently been considered as correlated with photosynthesis in several plant species. Collections of 165 mulberry (Morus sp.) germplasm accessions, both Indian and exotic in origin were evaluated for their variability with respect to SLW. The mean specific leaf weight ranged from 35.3 to $72.3 g/m^{-2}$. The distribution of SLW was found to be normal. High heritability (97.08%) and a small difference between genotypic and phenotypic variance demonstrates the genetic control over SLW. Significant heterotic effect with respect to SLW was observed in crosses when parents with high and low SLW were chosen.

• Journal of the Korea Concrete Institute
• /
• v.12 no.3
• /
• pp.3-10
• /
• 2000

In this study, we compared a plain mortar with the CAS-system shrinkage compensation mortar for Ondol that is Korean traditional heating system. The Ondol mortar is necessary to have properties as non-crack, fine flatness and stability for thermal changes. especially, mortar'crack prevention is to be most important property in Ondol mortar. To develope the stable material on the crack-prevention, we used to calcium-sulfo-aluminate(CSA)system in shrinkage compensation mortar. And so, we confirmed the effects of calcium-sulfo-aluminate(CSA) system for mortar's physical properties such as setting time, compressive strength and expansion ratio for crack prevention. The initial and final setting time of the CSA mortar is faster than plain mortar about 2hours. And, Compressive strength increased about 20% that plain mortar. The crack length per unit area, plain mortar is 0.426∼0.481m/m2. The Results of apartment construction field test, the shrinkage compensation mortar is excellent about the crack-reduce effect.

• Journal of information and communication convergence engineering
• /
• v.18 no.3
• /
• pp.167-175
• /
• 2020

The net income per unit area from crop production could be the most critical consideration for agricultural producers during cultivation planning. This paper proposes a scheme for predicting the net income per unit area based on machine learning and related calculations. This scheme predicts rice production and operation costs by applying climate and price index data. The rice price is also predicted by applying rice production and operation cost data. Finally, these predicted results are employed to calculate the predicted net income, which is compared with the actual net income. Consequently, the proposed scheme shows a meaningful degree of conformity, which indicates the potential of machine learning for predicting various aspects of agricultural production.

• Journal of Korea Foundry Society
• /
• v.18 no.3
• /
• pp.254-261
• /
• 1998

Microstructure and mechanical properties of the low pressure die-cast Al wheels were investigated by microscope, image analyzer, NDT (non-destructive test), and tensile test. The variation of SDAS (secondary dendrite arm spacing), porosity per unit area, quality grade, and tensile properties with the mold temperatures were examined. SDAS was gradually decreased with a decrease in temperature. However, the lowest value of porosity per unit area was observed at the mold temperature of $405^{\circ}C$ and the optimum mold temperature was found to be $405^{\circ}C$. Besides, from the observation of pore morphology, it was also found that the pore formation was mainly caused by shrinkage during solidification. The tensile strength, elongation, and impact toughness were markedly decreased, however the yield strength was nearly constant. The decrease of mechanical properties is attributed to the increase of porosity.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.34 no.1
• /
• pp.60-73
• /
• 1989

Two field experiments were carried out to assess the applicability of a central composite design (CCD) in determining optimum culture condition of an early rice cultivar, Unbongbyeo in southern Korea. A central composite design with two replicates was applied to five levels of five factors such as the number of hills per 3.3m2, the number of seedlings per hill, the levels of nitrogen, the transplanting date and the seedling age (Experiment 1). The levels of planting density were ranged from 30 hills to 150 hills per 3.3m2 ; the number of seedlings per hill from 1 seedling to 9 seedlings per hill; the levels of nitrogen application from 1 kg/l0a to 21 kg/l0a; the transplanting date from June 15 to July 5; the seedling age from 25 days to 45 days. A fractional factorial design was applied to three levels of five factors tested in CCD (Experiment 2). Yield per hill and per unit area were examined and the results obtained from both experiments were compared. The benefits from the central composite design were discussed. Maximum yield of brown rice per unit area was obtained at the combination of the central levels of one of five factors when the other four factors were fixed at central point. Furthermore, brown rice yield per unit area affected by interaction of two factors was maximized at the central point when the remain three factors being fixed at the central level. The responses of five factors to brown rice yield per hill and unit area were found to be a saddle point in both designs. Actual values of the stationary points were 107 hills per 3.3 m2, 4 seedlings per hill, 10 kg nitrogen per l0a, transplanting date of rice on June 26 and 33 days of seedling age in the central composite design. Brown rice yield per unit area at the stationary points were estimated 439 kg/l0a in the central composite design and 442 kg/l0a in the fractional factorial design. Considering the number of experimental treatment combinations, the central composite design was rather convenient in reducing the number of treatment combinations for similar information. It was more convenient for an experimenter to present the results from the central composite design than those from the fractional factorial design. Considering the optimum yields of brown rice per unit area at the stationary points being verified as saddle points in both designs. inter-heterogeneity of each of the factors should be avoided in setting up factors in pursuit of inducing unidirectional response of the factors to yield. Even though both the lower and higher levels in the central composite design being beyond the region of an experimenter's interest. they were considered highly valued in interpretation of the results. Conclusively. the central composite design was found to be more beneficial to optimize culture condition of paddy rice even with several levels of various factors were involved.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.24 no.2
• /
• pp.56-66
• /
• 1982

This study was carried out in order to estimate water losses in irrigation canals, which may be used to evaluate the water requirement for irrigation projects. The conveyance losses were measured by the inflow-outflow method, the seepage losses were measured by the ponding method, and the operation losses in the course of irrigation were calculated by comparing the two kinds of losses. The results obtained in this experiment were as follows; 1. Conveyance losses per unit area of wetted perimeter by the main irrigation canal, the secondary irrigation canal and the tributary irrigation canal, were 1.399${\times}10^{-5}m^3/sec/m^2$, 5.154${\times}10^{-5}m^3/sec/m^2$, and 2.67${\times}10^{-5}m^3/sec/m^2$ respectively in the Goong-sa area. And they were 1.934${\times}10^{-5}m^3/sec/m^2$, 2.149${\times}10^{-5}m^3/sec/m^2$, and 4.558${\times}10^{-5}m^3/sec/m^2$ respectively in the Seong-dug area. 2. Seepage losses per unit area of wetted perimeter by the secondary irrigation canal and the tributary irrigation canal, were 2.180${\times}10^{-6}m^3/sec/m^2$ and 2.168${\times}10^{-6}m^3/sec/m^2$ in the Goong-sa area, 1.150${\times}10^{-6}m^3/sec/m^2$ and 1.084${\times}10^{-6}m^3/sec/m^2$ in the Seong-dug area respectively. 3. Operation losses per unit area of wetted perimeter by the secondary irrigation canal and the tributary irrigation canal, were 4.936${\times}10^{-5}m^3/sec/m^2$ and 2.453${\times}10^{-5}m^3/sec/m^2$ in the Goong-sa area, 2.034${\times}10^{-5}m^3/sec/m^2$ and 4.450${\times}10^{-5}m^3/sec/m^2$ in the Seong-dug area respectively. 4. Conveyance, seepage and operation losses in the Goong-sa area were 6.7%, 94.6%, and 14.0% more than those in the Seong-dug area. Operation losses amount to about 17 times as much as seepage losses in the Goong-sa area and about 29 times in the Seong-dug area. 5. The seepage losses depend much on the soil texture, ranging from 7.437${\times}10^{-7}m^3/sec/m^2$ to 2.430${\times}10^{-6}m^3/sec/m^2$. 6. Water loss rates in the main irrigatin canal, the secondary irrigation canal and the tributary irrigation canal, were estimated as 8.49%, 37.27% and 9.81% respectively in the Goong-sa area. And they were estimated as 15.10%, 32.67% and 13.78% respectively in the Seong-dug area.