• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1987년도 전기.전자공학 학술대회 논문집(I)
• /
• pp.244-248
• /
• 1987

The force/torque sensor for robot is developed. The compliance algorithm for peg-in-hole insertion task using the forec/troque sensor is developed. The system consists of an IBM PC, robot, force/torque sensor, strain meter, A/D board, and interface board. The IBM PC functions as a main processor and the robot controller as a slave processor. The sensor is constructed to measure $T_x$, $T_y$, $F_z$ which are necessary to precisely execute a peg-in-hole insertion task by SCARA type assembly robot. The outputs of sensor are analyzed. On the basis of the analysis, compliance algorithm for peg-in-hole insertion task is developed. Some comments concerning the development of wrist force/torque sensor and compliance algorithm are given.

• 한국정밀공학회지
• /
• 제11권1호
• /
• pp.80-88
• /
• 1994

In the automation of rigid parts mating process with the intelligent robots, Peg-In-Hole is the most available task since inserting is some analytic and needs suitable range of forces that can be controlled by induatrial manipulators. In this Peg-In-Hole process, it is very important to identify the contact state between tow parts, peg and hole, to build the strategies for robot motion that leads to avoid the jamming condition occurs during insertion process. In this paper, we adpopted 3 parameters for identification, lFzl, lFxy/Fzl, and lMxy/Fxyl, derived from axes value of Whitney's jamming diagram. Also, we defined the fuzzy membership functions for these parameters and developed the identification algorithm based on fuzzy inference method of max-product. As an experimental result, we obtained about 96% of identification ratio that could be raised up to industrial requirements by further research.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2000년도 제15차 학술회의논문집
• /
• pp.410-410
• /
• 2000

Impedance control is recognised as one of the most proper control scheme to carry out the assembly tasks, since it can control the dynamic relationship between the manipulator and environment directly. However, it is well known that the contact force cannot be controlled directly using the impedance control. Also impedance parameters should be properly defined depending on the task to be performed. We propose a new position based impedance control, which has self-adjusted impedance parameters and can control the contact force explicitly, Impedance parameters, as time-varying parameters, are adjusted automatically based on the measured contact force and the position error during the task. A proposed algorithm was implemented on the peg-in-hole task with the industrial manipulator. We shows the effectiveness of proposed control method experimentally.

• 제어로봇시스템학회논문지
• /
• 제11권7호
• /
• pp.615-620
• /
• 2005

For successful deformable part assembly, information about its deformation as well as possible misalignment between the hole and its respective mating part are essential. Such information can be mainly acquired from visual sensors. In this paper, part deformation and misalignment in deformable cylindrical peg-in-hole tasks are measured by using a visual sensing system. First, a series of experiments to measure the position of an arbitrary point are performed. Next, an algorithm to measure misalignment and part shape as part deformation are presented, and a series of experiments on them are performed. Experimental results show that the proposed algorithms and the system are effective in measuring part deformation and misalignment.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 합동 추계학술대회 논문집 정보 및 제어부문
• /
• pp.119-122
• /
• 2001

This paper discusses the peg-in-hole task of chamferless parts using force/moment/vision sensors. The directional error occurring during the task are categorized into two cases according to the degree of initial errors, And different Mechanical analysis has been accomplished for each cases. This paper proposes an algorithm which enables to reduce intial directional error using digital Images acquired from hand-eyed vision sensor, And to continue the task even with the large directional error by adjusting the error using digital image processing. The effectiveness of the algorithm has been demonstrated through experimentation using 5-axis robot equipped with a developed controller force/moment sensor and color digital camera on its hand.

• 제어로봇시스템학회논문지
• /
• 제14권7호
• /
• pp.656-662
• /
• 2008

A cost-function based on manipulability and compatibility is designed to determine assembly motions of two cooperating manipulators. Assembly motions are planned along the direction maximizing performance indices to improve control performance of the two manipulators. This paper proposes bimanual task compatibility by defining cost functions. The proposed cost functions are applied and compared to the bimanual assembly task. The problem is formulated as a constrained optimization considering assembly constraints, position of the workpieces, and kinematics and redundancy of the bimanual robot. The proposed approach is evaluated with simulation of a peg-in-hole assembly with an L-shaped peg and two 3-dof manipulators.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2004년도 ICCAS
• /
• pp.1786-1790
• /
• 2004

The main objective of this paper is to analyze the performance of various force control algorithms in improving and adjusting the compliance of industrial robots in contact with their environment. Some of fundamental force control algorithms such as sensorless control, impedance control and hybrid position/force control are theoretically analyzed and simulated for various situations of an environment, and then a series of experiments using them were performed. In this paper, a control scheme to use position control in implementing the impedance control was investigated in order to nullify the effect of joint friction. The new reference trajectory is generated using contact force feedback and original desired trajectory. And an inner position control loop is designed to provide accurate position tracking for the new reference trajectory and good disturbance rejection. Experiments to insert a peg in a hole (so-called the peg-in-a-hole task) were performed with HILS (hardware-in-theloop simulation) system based on the results of the analyses and simulations on the characteristics of each control algorithm. The experiments showed that various force control methods improved the performance of robots in close contact with the environment by adjusting their compliance with respect to an arbitrary set of coordinates.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1989년도 한국자동제어학술회의논문집; Seoul, Korea; 27-28 Oct. 1989
• /
• pp.211-215
• /
• 1989

This paper describes a dynamic robotic assembly system in which an industrial robot executes peg-in-hole task in a moving state. As an effective means to synchronize the end-effector of the robot with the moving conveyor this work uses a control algorithm which is essentially a PID position control scheme combined with velocity feedforward loop. A RCC wrist is used for the inserting task and its force responses are investigated for various tracking conditions and inserting velocities through a series of experiments.

• International Journal of Control, Automation, and Systems
• /
• 제2권3호
• /
• pp.390-397
• /
• 2004

This paper presents the design and testing of a multi-channel vibrotactile display. It is composed of a cylindrical handle with four embedded vibrating elements driven by piezoelectric beams. Vibrations are transmitted to the hands through arrays of pins. The device was tested in sensory substitution for conveying force information during a teleoperated peg insertion. Results show that the device is effective in reducing peak forces during the insertion task.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1997년도 한국자동제어학술회의논문집; 한국전력공사 서울연수원; 17-18 Oct. 1997
• /
• pp.253-256
• /
• 1997

This paper proposes a control strategy of position and force control in the same direction based on hybrid position/force control. In order to control position and force in the same direction, a weighting matrix is introduced instead of a selection matrix suggested by Raibert and Craig. The major part of the controller output comes from the position controller when a position control error is large, from the force controller when a position control error is large. The proposed algorithm is implemented by the simulation and experiment focusing on the peg-in-hole task where friction exist significantly and is not constant. It also adopts and event control scheme for more efficient performance.