• Journal of the Architectural Institute of Korea Structure & Construction
• /
• v.35 no.12
• /
• pp.149-156
• /
• 2019

Recently, skyscraper building and apartment fires, which were rapidly spread out from a low floor to a rooftop, have become a frequent occurrence in mass media. This fire problems have a fatal disadvantage that the exterior wall finish of the building emits toxic gas in case of fire by using dry bit method or organic insulating material. Therefore, in order to remedy these problems, many exterior wall finishing construction methods have been proposed, but the current trend is to use existing construction methods due to problems such as economy, weight, and durability. On the other hand, in countries such as Germany and Japan, ceramic sidings are used as exterior finishing material for buildings, which is environmentally friendly, excellent natural beauty, long life, easy maintenance and high-quality exterior materials. However, those ceramic sidings have still the problems such as manufacturing cost and weight problem because of boosting the sintering temperature up to 1,350℃ or more. Also, conventional CRC, MgO, FRP sidings which are composed of pulp, glass fiber and organic materials, have been reports of deformation due to ultraviolet rays, discoloration, corrosion and scattering, surface rupture, lifting and peeling. Therefore, in this study as an alternative to solve this problem, halosite nano kaolin produced in Sancheong in Korea and frit flux were used to satisfy the required properties as ceramic siding using low temperature sintering (below 1,000℃) and lightweight materials such as pearlite. This study aims to design the optimal formulation and process of materials and to study the characteristics of nano-coated ceramic siding material development and to present relevant basic data. The findings show that ceramic siding for nanocoated building materials is excellent as a natural ceramic siding building material. The fire resistance of natural minerals and nano particle refining technology satisfy the bending strength of 80kgf / cm2, the volume ratio of 2.0 and the absorption rate of less than 10.0%.

• Applied Chemistry for Engineering
• /
• v.24 no.2
• /
• pp.148-154
• /
• 2013

UV curable acryl resin, pressure-sensitive adhesives (PSAs), are used in many different parts in the world. In particular, PSAs has been used in the wafer manufacturing process of semiconductor industry. As wafers become much thinner, UV curable PSAs require more proper adhesion performance. In this study, acrylic PSAs containing hydroxyl groups were synthesized using monomers of 2-ethylhexyl acrylate, 2-ethylhexyl methacrylate, styrene monomer and 2-hydroxyethyl acrylate. Isocyanate modified UV curable PSAs were then prepared by the adduct reaction that facilitates the UV curing property via controlling the amount of methacryloyloxyehtyl isocyanate. The proper adhesion performance and UV curing behavior of UV curable PSAs with various hydroxyl values were studied, and experimental conditions were then optimized to raise the efficiency of wafer manufacturing process. It was found that in case of using the equivalent ratio of 1 : 1 isocyanate hardener used in the UV curable PSAs, the peel strength before the UV curing process decreased as the amount of hydroxyl groups increased in the PSAs. The peeling adhesive strength was also decreased with increasing UV dose due to high curing characteristics.

• Korean Journal of Construction Engineering and Management
• /
• v.5 no.6 s.22
• /
• pp.212-217
• /
• 2004

Carbon fiber reinforced plastic(CFRP) plate Is one of the alterative materials for soengthening of reinforced and prestressed connote members due to excellent strength and light weight In this paper, the behavior of beams strengthened with CFRP plate and CFS(Carbon fiber sheet) is observed and analyzed from the test results. Especially specimens with thick plate is tested when large moment and large shear lone appear in same position. The main failure mode is a peeling-off of the CFRP plate near the loading points due to flexural-shear crack, Because of this failure mode, failure load is not linearly proportional to the thickness of CFRP plates. When beam is wrapped with CFS around oかy loading point it does not influence on the failure loads. Depending on the loading pattern, it is necessary to consider different design criteria for reinforced concrete members with external reinforcement. When line moment and large shear force appear in same location, maximum thickness may limit to 0.6mm and ratio between moment of strengthened beam and moment of unstrengthened beam is proposed 1.5-2.0. In order to use the plate of thicker than 6mm, CFS may be extended to the location which moment of strengthened beam is 1.5 times than moment of unstrengthened beam.

• Journal of Conservation Science
• /
• v.26 no.3
• /
• pp.335-340
• /
• 2010

Urethane resin applicable for the first transcription of historical site and transcription of soil layer were synthesized in order to replace the imported urethane resin, NS-10. Comparing to the NS-10, the urethane polymers showed similar penetration to wet soil and formed a stable layer of polyurethane during progress working the peeling off the polyurethane pre-product from epoxy surface of final product. The urethane resins used for the first transcription of historical site improved tensile strength, which is consistent with that of NS-10. In addition the urethane resin for transcription of soil layer was supplied with hardness that have a also same strong point as like NS-10. This property is advantage due to simplifying the transcription work of soil layer in backward. When we tested to the real ground soil as well as experimentation compressed soil with use these synthesis urethane resin, we ca get the satisfying result in penetration property and stability and these properties evaluated the resins as an advanced product serving better convenience for worker.

• Korean Journal of Food Science and Technology
• /
• v.31 no.6
• /
• pp.1583-1588
• /
• 1999

Garlic pieces without peeling were subjected to hot air heating at $60{\sim}90^{\circ}C$ for 30 min. and microwave oven heating for 10 sec to reduce the strength of garlic flavor. Volatile compounds of the treated garlic were decreased, as the heating temperature was raised. Garlic heated at 70, 80 and $90^{\circ}C$ had 20%, 31% and 49% less volatile compounds, respectively, compared to those of the control. Microwave oven heating revealed a similar trend to those heated at $60{\sim}80^{\circ}C$. As the heating temperature was raised, glucose, fructose and fructooligosaccharide contents in the heated garlic were decreased. Pyruvic acid contents in garlic, a degradation product of alliin, was decreased as the heating temperature was raised, but contents of the other organic acids were not affected. Arginine, the main amino acid in garlic was decreased by the hot air heating, but was not affected by the microwave heating. Glutamic acid and tyrosine contents were decreased in all the treated garlic samples.