• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.08a
• /
• pp.27-36
• /
• 2004

Contemporary objectives for steel rod rolling processing are increasingly complex and often contrasting i.e. obtaining a desired product with optimum combination of properties such as strength, toughness and formability at lower cost. Low-alloy steel rods have been produced with several heat treatments for drawing and forging processes at room temperature. In order to reduce these heat treatments much of the researches concerning of high temperature mechanical behavior of steel rods have been conducted at wire rod mill of POSCO. In this present work, optimizations of rolling temperature and cooling rate for JS-SCM435 are performed to eliminate softening heat treatment(Low Temperature Annealing) for drawing process. The results from the optimization changed the microstructure of rods after rod rolling from Bainite with high tensile strength of 1000Mpa to Pearlite and Ferrite with appropriate strength of 750Mpa that is equivalent tensile strength after softening heat treatment.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.08a
• /
• pp.356-365
• /
• 1999

The present study is aimed at developing the TRIP(transformation induced plasticity) aided high strength low carbon steel using reversion process. An excellent combination of elongation over 40% and tensile strength abut 100kgf/$\textrm{mm}^2$ achieved in processing of 0.15C-0.5 Si-6Mn steel by slow heating to intercritial temperature region and accelerated cooling into room temperature. This good combination is caused by TRIP phenomena of retained austenite in steels during deformation. The stability of retained austenite is very important for the good ductility and it depends on the diffusion of carbon and manganeses during heat treatment. The accelerated cooling after holding at annealing temperature retards the formation of pearlite and provides the carbon enrichment in retained austenite in steel, resulting in the increase in elongation of the cold-rolled TRIP steel. On the other hand, heat treating the steel at 600$^{\circ}C$ for 5 hour before cold rolling increases elongation but reduces the amount of retained austenite after reversion processing. It is accounted that the heat treating is effective for the increase in the stability of retained austenite.

• KIEAE Journal
• /
• v.13 no.1
• /
• pp.65-74
• /
• 2013

Recently, greenery system is frequently applied on buildings and artificial grounds to improve urban ecological functionality. Specifically, architectural greenery is also known as an architectural language that can meet the sustainable design concept of architects. Although the architectural greenery system can be optimized through an interdisciplinary approach between architecture, horticulture and landscape- architecture, there is a problem of communication on the ideal gap between them. Therefore, this study is expected to establish the comtemporary architecture as hi-tech and the organic architecture in internationalism. Moreover, it can analyze the case study on architectural greenery system designed by a Pritzker Prize winner who represents the comtemporary architectural trend. In this analysis, we calculate and compare the U-value of the free-form surface system based on the international standards: ISO and CIBSE etc. Moreover, we calculate a change of artificial soil transmittance respect on compounding ratio of the bottom ash and pearlite. In the case of California Academy of Science by Renzo Piano, total transmittance of the greenery system results in 48% of domestic thermal insulation standard in dry condition. This result will be used as a basic study to promote developing the advanced system based on the concept of consilience.

• Journal of Korea Foundry Society
• /
• v.20 no.3
• /
• pp.173-180
• /
• 2000

The microstructure changes of the matrix and the graphites were observed by optical microscope and the average hardness number was investigated according to the heat-treatment conditions of the cast iron rods by the horizontal continuous casting process in 35 mm diameter. The three kinds of heat-treatments were introduced. The first treatment was performed at 900, 950, and $1000^{\circ}C$ for 2 hours and the second treatment was conducted during 5, 10, and 15 hours at $1000^{\circ}C$ respectively. The third treatments were the two-cyclic heat-treatment and the three-cyclic heat-treatment at $1000^{\circ}C$ during 2 hours. The matrix microstructure of the specimens to be treated at various temperatures for 2 hours was the ferrite to be transformed from the pearlite The hardness number of the center of the samples according to the heat treatment time at $1000^{\circ}C$ was higher than that of the surface area because of the martensite formation in the center. Also, in the cyclic heat-treatments, the hardness number of the two-cycle treatment specimens increased because of the martensite formation in the center.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.7 no.5
• /
• pp.66-71
• /
• 1998

It is required the superior materials for the parts of machines or structures, which could be endurable in severe load and environment. According to advancement of casting technology, nodular graphite cast iron is used as suitable for such condition. But nodular graphite cast iron is scattering of fatigue strength and low reliability. Therefore in this study, the effect of matrix structure and number of nodular graphite on the initiation of fatigue crack and fatigue strength. It was found that the material which has relatively high ferrite volume fraction was more easily cracked than other materials and fatigue limit was low. The material which has not found pinhole on the surface, the crack was initiated in graphite went through ferrite and propagated into through graphite, but separated graphite and ferrite grain boundary and combined with other cracks to fro large one.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.23 no.6
• /
• pp.618-623
• /
• 2014

This study, analyzed the waveform and mechanical properties of flux cored arc Welding on SM45C. $CO_2$ 10% + Ar 90% shows the lowest standard deviation and shunt ratio at which the arc was most stable. $CO_2$ 10% + Ar 90% is equal to $CO_2$ 20% + Ar 80%. therefore, $CO_2$ 20% + Ar 80% is the best of mixture gases. The hardness test result for the gas mixture ratio of $CO_2$ 10% + Ar 90% was HV 249.7 which is the highest measured value. According to tensile test results, the tensile strength increased with increasing Ar in the mixture gas. This was because of the inertness of the argon, which does not combine with other elements, causing $CO_2$ to combine with pearlite and ferrite and decreasing the maximum tensile strength. Microstructural examination results show that with increasing Ar, ferrite generation decreases while the mild microstructure increases which influences the hardness.

• Journal of the Korean Society for Heat Treatment
• /
• v.1 no.1
• /
• pp.13-23
• /
• 1988

The hardenability of alloyed ductile cast irons was studied for 54 different alloy compositions obtained from eight commercial and laboratory foundries. The alloying elements investigated for their effects on hardenability were Si(2.0 to 3.0%), Mn(0.0 to 0.8%), Mo(0.0 to 0.6%), Cu(0.0 to 1.5%), and Ni(0.0 to 1.5%). Two hardenability criteria, a first-pearlite hardenability criterion and a half-hard hardenability criterion, were used to determine hardenability of ductile irons. Prediction models for each hardenability criterion were developed by multiple regression analysis and were well agreed with previous experimental results. Molybdenum was the most potent hardenability promoting element followed by manganese, copper and nickel ; silicon had little effect on hardenability and reduced the hardenability as silicon content increased. When alloying elements were presented in combination, strong synergistic effects on the hardenability were observed especially between molybdenum, copper and nickel. The hardenability of ductile iron was strongly influenced by austenitizing temperature. Increasing austenitizing temperature up to $955^{\circ}C$, hardenability increased gradually but decreasing rate and then decreased as temperature increased above $955^{\circ}C$. Unless reducing segregation by very long-time annealing treatment, the hardenability of ductile iron was not significantly influenced by segregation of alloying elements.

• Journal of the Korean Society for Heat Treatment
• /
• v.4 no.3
• /
• pp.39-46
• /
• 1991

The effects of austenitizing temperatures and times and cooling rate on the characteristics of continuous air cooling have been investigated for 0.3%C-Mn steels microalloyed with vanadium. Transformation start temperatures have been found to be measured from temperature-time curve directly obtained with continuous air cooling and to decrease with increasing austenitizing temperature, cooling rate and Mn contents. The coarsening behavior of austenite grain size has been measured to abnormally grow at $1050^{\circ}C$ and rapidly grow at $1200^{\circ}C$. It has been found that the volume fraction of pearlite was linealy proportional to the reciprocal square root of austenite grain size. The hardness has been measured to increase with increasing cooling rate up to $250^{\circ}C/min.$ and to remain relatively unchanged in the range of $250{\sim}400^{\circ}C/min.$ showing that hardness valves for steel with a higher Mn content increase more than those for steel with a lower Mn content. The impact property has been found to decrease with increasing of austenite grain size but does not linealy change with the reciprocal square root of austenite grain size.

• Journal of the Korean Society for Heat Treatment
• /
• v.11 no.1
• /
• pp.46-53
• /
• 1998

The variation of the mechanical properties, microstructures and the formation of retained austenite with heat treatment conditions in austempered ductile cast iron has been investigated. In the case of austempered ductile cast iron below 25mm diameter, it has been found that a pearlite structure are not obtained under a super cooled condition at range of $0.05^{\circ}C/sec{\sim}10^{\circ}C/sec$, and the matrix is precipitated in graphite, bainite and retained austenite. After austempering treatment the retained austenite is increased with decreasing cooling rate. The elongation increases with decreasing super cooling rate, and the optimum result has been shown to be the elongation of 15.6% at super cooling rate of $0.05^{\circ}C/sec$. The optimum result has been shown to be the tensile strength-elongation balance of $1656kgf/mm^2.%$ and it is more than doubled to as the casting state and continuous cooling condition.

• Journal of the Korean Society for Heat Treatment
• /
• v.28 no.4
• /
• pp.171-180
• /
• 2015

The variation in microstructure and texture during continuous annealing was examined in a series of 1.6% Mn-0.1% Cr-0.3% Mo-0.005% B steels with carbon contents in the range of 0.010 to 0.030%. It was found that microstructure of hot band consisted of ferrite and pearlite as a consequence of high coiling temperature, and eutectoid carbon content was between 0.011% and 0.016%. Martensite ranged in volume fraction from 1.5% to 4.0% when annealed at $820{\circ}C$ according to the typical continuous annealing cycle. The critical martensite content for the continuous yielding was about 4% from stress-strain curves. The continuous yielding was obtained in the 0.030% carbon steel and 0.010% to 0.020% carbon steels revealed some yield point elongation ranging from 0.8% to 2.2% in as-annealed conditions. Higher tensile strength in the higher carbon steel is due to both increase in the martensite volume fraction and ferrite grain refinement. Decreasing the carbon content to 0.01% strengthened the intensities of ${\gamma}$-fiber textures, resulting in the increase in the $r_m$ value, which was caused by the lower volume fraction of martensite. The higher carbon steels showed the lower $r_m$ value of about 1.0.