• Korean Journal of Optics and Photonics
• /
• v.19 no.1
• /
• pp.68-72
• /
• 2008

Fiber-optic strain sensors based on Bragg reflection gratings produce the change of reflection spectrum when an external stress is applied on the sensor. To measure the Bragg reflection wavelength in high speed, an arrayed waveguide grating device is incorporated in this work. By monitoring the output power from each channel of the AWG, the peak wavelength corresponding to the applied strain could be obtained. To enhance the accuracy of the AWG wavelength interrogation system, a chirped fiber Bragg grating with a 3-dB bandwith of 5.4 nm is utilized. The high-speed response of the proposed system is demonstrated by measuring a fast varying strain produced by the damped oscillation of a cantilever. An oscillation frequency of 17.8 Hz and a damping time constant of 0.96 second are obtained in this measurement.

• Journal of the Korean Geotechnical Society
• /
• v.21 no.7
• /
• pp.31-42
• /
• 2005

In this study, a rockfill-dam material was investigated on its shear strength and compressibility by performing large-scaled triaxial and oedometer tests. The rockfill material was compacted at two different compaction levels and sheared in triaxial compression at three different confining stresses. Also, rockfill samples were prepared to have three different grain size distributions but the same dry density. Each sample with a given grain size distribution was then compressed one-dimensionally in a large-scaled oedometer cell with and without soaking. The rockfill samples exhibited slightly different shear behaviors with the varying compaction and confining stress levels. The increase in the compaction level changed the behavior from contractive to dilative. Dilation decreased gradually with increasing confining stress, resulting in reduction in the peak shear strength. The large-scaled oedometer test results showed that particle breakages increased with increasing average particle sizes of the samples. Comparing the samples with different gradations, a relatively well-graded sample exhibited lower compressibility. For saturated samples, slightly higher deformations were observed, compared to dry samples. The values of tangent constrained modulis for the dry samples were larger by about 10 to 20$\%$, on the average, than those for the saturated samples.

• Journal of the Korean Society of Safety
• /
• v.24 no.6
• /
• pp.63-71
• /
• 2009

In order to improve flame retardancy, the halogen free organic melamine phosphate(M-P) flame retardant was synthesized from melamine and phosphoric acid by the reaction of precipitation. The ignition test was carried out preparing hybrid flame retardant compound($H_bFRC$) consisting of organic M-P and inorganic Mg$(OH)_2$ as a flame retardant in the polyolefin resins. The flame retardancy and mechanical properties of flame retardant aluminum composite panel($H_bFRC$-ACP) were performed to investigate the possibility of the composite material, which was contained M-P, as a inner core for $H_bFRC$-ACP. For this study, the results of ignition test indicate that a char formation and drip suppressing effect, and combustion time reduced as the content of M-P increased. The limited oxygen index(LOI) values were measured 17.4vol% and 31.5vol% for LDPE only and $H_bFRC$-3(M-P content: 15wt%), respectively. And it was verified that the $H_bFRC$-3 was needed more oxygen quantity with the increase of M-P content when it combustion. Also, the results from thermogravimetric analysis were observed endothermic peak at $350^{\circ}C$ and $550^{\circ}C$, it was confirmed predominant thermal stability though the wide temperature range by the mixture of M-P and Mg$(OH)_2$. The LDPE-ACP (using only LDPE as a inner core), $35.13kW/m^2$ of heat release rate(HRR) and 13.43MJ/m2 of total heat release(THR) were measured while the $H_bFRC$-ACP, $10.44kW/m^2$ of HRR and 1.84MJ/m2 of THR were measured by results of cone calorimeter test. In case of $H_bFRC$-ACP, the average gas emission amount of CO and $CO_2$ could be decreased down to 25% and 20%, respectively, in comparison with LDPE-ACP. The mechanical properties such as tensile strength, bending strength and adhesion strength of $H_bFRC$-ACP were revealed slightly high values $54N/mm^2$, $152N/mm^2$ and 120N/25mm, respectively, compared with LDPE-ACP. It was confirmed that flame retardancy was improved with the synergy effect because of char formation by M-P and hydrolysis by Mg$(OH)_2$. The result of this study suggest that $H_bFRC$ can be applied for an adequate halogen free flame retardant composite material as a inner core for ACP.

• Korean Journal of Poultry Science
• /
• v.27 no.2
• /
• pp.115-132
• /
• 2000

Eggshell strength and eggshell pigmentation are described in this paper since these are needed for quality egg production. A strong eggshell is determined by the components of the shell (cuticle, true shell and membranes) as well as the proper function of the gastrointestinal tract, the shell gland, the Kidneys and the endocrine system. When the puller reaches sexual maturity, the medullary bone must be ready for the laying hen at the peak egg shell formation. The amount of calcium in the layer diet, sources of calcium feed, the ratio of calcium and phosphorus in the layer diet, adequate levels of vitamin D and the dietary mineral (electrolyte) balance in the body fluid are important factors along with the levels of other nutrients. Biological, environmental and managerial factors such as the age of laying flock, temperature and humidity of the hen house, bird strain, disease, egg collection through transportation and others and influence the shell breakage at various stages of movement of the eggs from the producer to the consumer. The pigments present in eggshells are protoporphyrin-Ⅸ, biliverdin-Ⅸ and its zinc chelate and occasional traces of coproporphyrin-Ⅲ. However, there are several causes of changes in eggshell pigmentation such as the age of hen, disease, drugs and surface defects due to abnormal post-cuticular deposits.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.119-119
• /
• 2009

인버터 DC 저항용접의 적용성 증대 : 인버터 DC 저항용접 공법이 SPOT, PROJECTON, SEAM, BUTT 등의 공정에 다양하게 적용되어 저항용접 현장에서 고효율, 친환경적 용접 환경을 만드는데 일조 하고 있다. 특히 자동차의 경량화, 충돌내성 증대, 진동 및 내구성 증대, 공간활용 극대화, 새로운 Design 개념 적용 등의 산업전반에 걸쳐 나타나는 신 Trends로 고 장력 철재의 적용 범위가 확대되고 HSS(High Strength Steel), EHSS(Extra High Strength Steel), UHSS (Ultra High strength Steel ; Hot - Formed Steel )등 다양한 철판의 SPOT 저항용접이 필요하게 되었다. 기존의 AC 단상용접의 전력 특성 상 통전 중 무 통전 시간 과 높은 PEAK 전력, 단상 대 전력 소모로 인한 전력 DROP 등의 문제로 인하여 신소재의 용접 시 매우 많은 Spatter가 발생하고, 높은 용접품질의 확보가 어려워 지므로 이를 대체하기 위한 공법으로 MFDC ( 인버터 DC 저항용접공법 )이 적용되고 있다. 인버터 DC 저항용접의 적응제어 : MFDC라는 높은 효율의 용접 전력원이 확보 됨에도 불구하고 용접현장에서는 원 자재, 도금 등의 품질 산포, 프레스 물의 가공산포, 공기압 산포, 전극 과열 및 마모 등의 요인에 의하여 저항용접 산포가 발생하고 있다. 이는 인위적인 조작이 어렵고 불규칙적이며, 어디서나 산재하고 있는 문제이다. 이를 용접전력 제어 법으로 개선하여 일정한 용접성을 확보하기 위한 노력이 적응제어 기법이다. 정 전류, 정 전력 제어는 정량 제어로 용접 물을 비롯한 용접부의 변화와는 관계없이 설정된 일정량의 전력을 공급하기만 하는데 반하여 적응제어는 적절한 용접 작업 시의 용접 물의 상태, 전극의 가압, 표면 상태 등에 따른 변화 페턴을 기억하고 이후 진행되는 용접에 대하여 정상 페턴과의 차이를 감지 이를 보상하므로 고품질의 용접성을 보장하는 제어기법이다. 따라서 다양한 용접 산포 유발 요인에 의해 용접부의 변화가 발생한다 하여도 그 변화를 감지 하고 적절한 용접전력을 공급한다면 고품질의 용접성을 확보하는데 유용한 공법이 될 수 있다. 인버터 DC 저항용접의 SPC 관리 : SPOT 용접 시 획득할 수 있는 다양한 파라메터에 대하여 모니터링 하고 이 자료를 data 화 하여 품질 관리에 응용하게 되면 양산라인에서 반복적으로 발생되는 문제점을 확인 할 수 있고 이를 통계적 방법으로 추적 개선해 나간다면 용접 불량 감소 및 생산성 향상에 도움이 되며 작업자의 공정 능력 향상 및 기업의 기술축적에도 높은 기여를 할 수 있을 것이다. 용접 적응제어와 다양한 파라메터 모니터링이 한 system에서 이루어 질 때 높은 용접성 확보와 불량률 감소, 원가절감, 생산성 향상 등의 효과가 극대화 될 것이다.

• Korean Journal of Applied Biomechanics
• /
• v.31 no.4
• /
• pp.241-248
• /
• 2021

Objective: The purpose of this study was to investigate the difference in muscle strength, kinematics, and kinetics between injured and non-injured sides of the leg after Achilles Tendon Rupture surgery during walking and running. Method: The subjects (n=11; age = 30.63 ± 5.69 yrs; height = 172.00 ± 4.47 cm; mass = 77.00 ± 11.34 kg; time lapse from surgery = 29.81 ± 10.27 months) who experienced Achilles Tendon Rupture (ATR) surgery participated in this study. The walking and running trials were collected using infrared cameras (Oqus 300, Qualisys, Sweden, 100 Hz) on instrumented treadmill (Bertec, U.S.A., 1,000 Hz) and analyzed by using QTM (Qualisys Track Manager Ver. 2.15; Qualisys, U.S.A). The measured data were processed using Visual 3D (C-motion Inc., U.S.A.). The cutoff frequencies were set as 6 Hz and 12 Hz for walking and running kinematics respectively, while 100 Hz was used for force plate data. Results: In ATR group, muscle strength there were no difference between affected and unaffected sides (p> .05). In kinematic analysis, subjects showed greater ROM of knee joint flexion-extension in affected side compared to that of unaffected side during walking while smaller ROM of ankle dorsi-plantar and peak knee flexion were observed during running (p< .05). In kinetic analysis, subjects showed lower knee extension moment (running at 2.2 m/s) and positive ankle plantar-flexion power (running at 2.2 m/s, 3.3 m/s) in affected side compared to that of unaffected side (p< .05). This lower positive ankle joint power during a propulsive phase of running is related to slower ankle joint velocity in affected side of the subjects (p< .05). Conclusion: This study aimed to investigate the functional evaluation of the individuals after Achilles tendon rupture surgery through biomechanical analysis during walking and running trials. Based on the findings, greater reduction in dynamic joint function (i.e. lower positive ankle joint power) was found in the affected side of the leg compared to the unaffected side during running while there were no meaningful differences in ankle muscle strength and walking biomechanics. Therefore, before returning to daily life and sports activities, biomechanical analysis using more dynamic movements such as running and jumping trials followed by current clinical evaluations would be helpful in preventing Achilles tendon re-rupture or secondary injury.

• Journal of the Korean Geotechnical Society
• /
• v.36 no.12
• /
• pp.77-86
• /
• 2020

In this study, the importance of implied strength correction for shallow depths at a region of moderate to low seismicity with primary focus on its effect upon site natural period and mean period of the ground motion is investigated. In addition to the most commonly used Modified Kondner-Zelasko (MKZ) model, this paper uses a quadratic/hyperbolic (GQ/H) model that can capture the stress - strain response at large strains as well as small strain stiffness dependence. A total of six site profiles by downhole tests are used and 1D site response analyses are performed using three input motions with contrasting mean periods. The difference between non-corrected and corrected analyses is conditional on the site period as well as mean ground motion period. The effect of periods is analyzed by correlating them with the effective peak ground acceleration, maximum shear strains and amplification factors. The comparative study reveals that the difference is more prominent in soft sites with long site periods. Insignificant differences are observed when soil profiles are subjected to ground motion with very short mean period.

• Journal of the Korean Geotechnical Society
• /
• v.26 no.2
• /
• pp.23-32
• /
• 2010

This study was especially conducted to find out the characteristics of the lightweight air-mixed soil (slurry density 10 kN/$m^3$) containing silt related to water. Compression strength, permeability, and capillary height of the lightweight air-mixed soil were studied, and also to support these studies, the structure of that soil was analyzed in detail. Air bubbles of various sizes are inside the lightweight air-mixed soil, and its distribution in a location is almost constant. A numerous tiny pores are inside the air bubbles so that the lightweight air-mixed soil can be saturated with water. Porosity is also estimated through the image analysis. Peak strength of the lightweight air-mixed soil is not dependent on water, but behavior of stress-strain is affected by the water. Permeability is about $4.857{\times}10^{-6}cm/sec$, which is a little bit higher than the clay's permeability. Capillary rise occurs rapidly at the beginning of the test until the lapse of 100 minutes and then its increase rate becomes slow. The capillary rise causes the increase of the density of the lightweight air-mixed soil, and thus it is required to pay attention to this phenomenon during structure design and maintenance of the lightweight air-mixed soil.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.36 no.4
• /
• pp.362-368
• /
• 2023

Multilayered actuators using Pb(Mg_1/3Nb_2/3)O₃-Pb(In_1/2Nb_1/2)O₃-PbTiO₃ (PMN-PIN-PT) crystals have demonstrated excellent properties, but are costly and lack mechanical strength. Textured PMN-PIN-PT ceramics exhibit robust mechanical strength and comparable properties to their single crystals form. However, the development of multilayered actuators using textured PMN-PIN-PT ceramics has not been achieved until now. This study presents the development of a multilayered actuator using textured 0.37PMN-0.29PIN-0.34PT ceramics with an Ag_0.9/Pd_0.1 inner electrode, co-fired at 950℃. A random 0.37PMN-0.29PIN-0.34PT ceramics multilayered actuator was also developed for comparison. The multilayered actuator consisted of 9 ceramic layers (36 ㎛ thickness) with an overall actuator thickness of 0.401 mm. The textured and random 0.37PMN-0.29PIN-0.34PT ceramics-based multilayered actuators achieved displacements of 0.61 ㎛ (0.15% strain) and 0.23 ㎛ (0.057% strain) at a low applied peak voltage of 100 V. These results suggest that the developed multilayered actuator using high-performance textured 0.37PMN-0.29PIN-0.34PT ceramics has the potential to replace expensive single crystal-based actuators cost-effectively.

• Journal of Animal Science and Technology
• /
• v.45 no.3
• /
• pp.369-376
• /
• 2003

This experiment was conducted to investigate the influence of different levels of metabolizable energy (ME) and crude protein (CP) on post-molt performance and egg quality of spent laying hens. Four hundred and thirty two, ISA Brown hens at sixty six weeks of age after molt induction were fed six experimental diets containing three ME (2,750, 2,800, 2,850 kcal/kg) with two CP (15, 17%) levels in a factorial design. The influence of ME and CP were evaluated on egg production, egg weight and feed intake throughout 24 weeks of production. Egg mass and feed conversion ratio (FCR) were measured during the experimental period. Haugh unit, yolk color and eggshell breaking strength were measured at 5%, 50%, peak, post peak and end stage of egg production. The hens fed 2800 kcal/kg diet along with 15% CP recorded the highest outcome of egg production (P<0.05). The egg weight has been shown to increase with hens receiving 2,800 kcal/kg ME. Daily egg mass tended to increase in hens fed with 15% CP and 2,800 kcal/kg ME. Feed intake decreased significantly with the level of ME and CP in the diet increased (P<0.05). Yolk color was improved significantly in eggs laid by the hens receiving 17% CP than 15% diet. It also tended to be higher in 17% CP with 2,800 or 2,850 kcal/kg ME diet treatments. Egg shell breaking strength increased with hens receiving diets of 15% CP and 2,800 kcal/kg. From this experiment it can be concluded that the ME level of 2,800 kcal/kg coupled with 15% CP could be used to achieve the higher egg production and better eggshell strength in induced molting hens.