• 물과 미래
• /
• 제28권3호
• /
• pp.187-195
• /
• 1995

본 연구의 목적은 20년 전에 건설 완료된 우리나라 최대 다목적댐인 소양강 다목적댐의 치수능력을 재검토하여 그 대안을 제시하는데 있다. 최악의 기상조건을 고려하여 수문 기상학적 방법으로 산정한 소양강 다목적댐유역의 72시간 지속 가능 최대 강수량(PMP, probable maximum precipitation)은 760.0mm 이며 재산정된 가능 최대 홍수량(PMF, probable maximum flood)은 18,100$m^3$/s이다. 이는 댐 계획 당시 1,000년 빈도 홍수량의 최대치 13,500$m^3$/s 보다 1.34배 크게 나타났다. 가능 최대 홍수량을 설계 홍수량으로 채택할 경우의 4개 대안; 1) 하수 제한수위를 낮추는 안, 2) 비상 여수로를 추가하는 안, 3)기존 댐을 증고시키는 안, 4) 상류에 홍수조절용댐을 건설하는 안 등을 검토한 결과 경제성과 치수 관리 능력 효율면에서 소양강 다목적댐의 수문학적 안정성을 도모할 수 있는 최적의 개선 방안은 비상 여수로를 추가하는 안으로 판단된다. 따라서 현 여수로에 부가하여 비상 여수로를 추가하는 방안이 보다 더 구체적으로 검토되어야 할 것이다.

• 마이크로전자및패키징학회지
• /
• 제8권1호
• /
• pp.1-4
• /
• 2001

새로운 구조의 APF optical link용 Si pin photodetector를 제작하고 그 특성을 분석하였다. 제작된 소자는 금속-반도체 접촉주위에 $p^{+}$-guard ring구조와 광이 입사되는 수광면에 그물망 모양의 얕은 $p^{+}$-확산영역을 갖는다. 제작된 소자의 전기.광학적 특성을 -5 V의 동작전압에서 측정한 결과, 접합 커패시턴스와 암전류는 각각 4 pF와 180 pA로 나타났으며 광신호 전류와 감도특성는 670 nm이 중심파장을 갖는 2.2 $\mu$W의 입사광 전력 아래에서 각각 1.22 $\mu$A와 0.55 A/W로 나타났다. 제작된 소자는 650~700 nm의 파장영역에서 최대 spectral response를 보이고 있으며 낮은 점한 커패시턴스와 우수한 신호분리능력으로 인해 red light optics응용에서 광신호 검출에 적합하게 사용될 수 있을 것으로 기대된다.

• Journal of Electrochemical Science and Technology
• /
• 제7권1호
• /
• pp.68-75
• /
• 2016

In this study a new, simple, precise, accurate and economic electrochemical method was developed and validated for the voltammetric determination of zolpidem (ZP) using disposable pencil graphite (PG) electrode. The anodic oxidation of ZP on the surface of the PG electrode was examined in a britton robinson (BR) buffer. Square wave and cyclic voltammetry were used as electrochemical techniques in the potential range of 0-1.2 V in the pH 8 BR buffer. In cyclic voltammetry studies, the diffusion coefficient of ZP oxidation was found to be 3.6×10^-6 cm² s^-1. On the other hand, the ZP has shown a well-defined irreversible anodic peak at 0.98 V in the square wave voltammetry mode. The PG electrode, primarily being graphite which has a large active surface area gives rise to increasing peak current with respect to ZP electrooxidation. PG electrode showed an electrocatalytic effect in anodic oxidation of ZP. A linear relationship between catalytic current response and ZP concentration was obtained over a concentration range of 10-30 μM with R.S.D. values ranging from 0.29-3.89. Limits of detection and quantitation were found to be 1 and 3 μM, respectively. Finally, the PG electrode was successfully used to determine ZP in standard and tablet dosage forms with a mean recovery of 100.69 %.

• 대한기계학회논문집
• /
• 제17권2호
• /
• pp.300-312
• /
• 1993

The material deterioration of service-exposed boiler tube steels in fossil power plant was evaluated by using the electrochemical technique namely, modified electrochemical potentiokinetic reactivation(EPR). It was focused that the passivation of Mo$_{6}$C carbide which governs the mechanical properties of Mo alloyed steels did not occur even in the passivity region of steel in sodium molybdate solution and the reactivation peak current (Ip) observed as the result of non-passivation indicating the precipitation of Mo$_{6}$C carbides. To obtain the optimal test conditions for the field test by using the specially designed electrochemical cell, the effects of scan rate, the surface roughness and the pH of electrolyte on Ip value were also investigated. Furthermore, the change of mechanical properties occurred during the long time exposure at high temperature was evlauated quantitatively by small punch(SP) tests and micro hardness test taking account of the metallurgical changes. It is known that reactivation peak current (Ip) has a good relationship with Larson-Miller Parameter(LMP) which represents the information about material deterioration occurred at high temperature environment. In addition it was possible to estimate the ductile-brittle transition temperature (DBTT) by means of the SP test. The Sp test could be, therefore, suggested as a reliable test method for evaluating the material degradation of boiler tube steels. From the good correaltion between the SP DBTT and Ip values shown in this study, it was knows that the change of mechanical properties could be evaluated non-destructively by measurring only Ip values.ues.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 제2회 학술대회 논문집 일렉트렛트 및 응용기술전문연구회
• /
• pp.11-14
• /
• 2000

This paper describes a thennally stimulated displacement current(TSDC) of polyamic acid alkylamine salts(PAAS) Langmuir-Blodgett(LB) films, which is a precursor of polyimide(PI). The TSDC measurements of PAAS LB film were performed from room temperature to about $250^{\circ}C$ and the temperature was increased at a rate of $0.2^{\circ}C/s$. This show that this is TSDC peaks at about $70^{\circ}C$ in the arachidic acid LB films, and at about $70^{\circ}C$ and $160^{\circ}C$ in the PAAS LB films. Results of this measurements indicate that one small peak at $70^{\circ}C$ is resulted from a softening of the alkyl group and the large peak at $160^{\circ}C$ is possibly due to dipole moment of C-O group in the PAAS molecule. We have calculated the vertical component of dipole moment of the P AAS LB film out of the TSDC curves. It shows that the dipole moment of PAAS LB film is about -40mD at $70^{\circ}C$ and about 200mD at $160^{\circ}C$ in the first measurement of TSDC. In the second measurement of TSDC of PAAS LB film after cooling down to room temperature, the TSDC peaks are almost disappeared.

• 한국진공학회지
• /
• 제1권1호
• /
• pp.126-133
• /
• 1992

E-Beam 기법을 이용하여 증착시킨 Ag doped CdS 박막은 육방정계이고 공기, Ar 분위기에서 $^550{\circ}C$로 열처리한 결과 grain size가 1$mu extrm{m}$ 정도로 성장되었고, Van Der Pauw 방법으로 구한 Hall data로부터 CdS crystal은 n형 반도체이고 상온에서의 carrier 농 도는 2.7 $\times$ 1011cm-3이고 Hall mobility는 5.8 $\times$ 102cm2V-1sec-1정도임을 알 수 있었다. CdS : Ag 박막의 PL spectra는 Gaussian curve를 보여주었고, spectra peak는 파장이 520nm 근처에 위치하고 있으며, CdS : Ag 박막에서의 광전류(pc)와 암전류(dc)의 ratio(pc/dc)는 공기 중에서 열처리한 시료의 값이 크다는 것을 알 수 있었다.

• 대한약리학회지
• /
• 제32권2호
• /
• pp.283-292
• /
• 1996

The spinal dorsal horn is the area where primary afferent fibers terminate and cutaneous sensory information is processed. A number of putative neurotransmitter substances, including excitatory and inhibitory amino acids and peptides, are present in this region. In this study, single neurons of the spinal dorsal horn were acutely isolated and the properties of whole cell current and responses to excitatory and inhibitory neurotransmitters were studied by patch clamp technique. Transverse slice ($(300{\mu}m$) of lumbar spinal cords from young rats$(7{\sim}14\;days)$ were sequentially treated with two pretenses(pronase 0.75 mg/ml and thermolysin 0.75 mg/ml), then single neurons were mechanically dissociated. These neurons showed near-intact morphology such as multipolar, ellipsoidal and bipolar, and pyramidal cells and we recorded the typical whole cell currents of $K^+$, $Ca^{2+}$ and ligand-operated channels from these neurons. Glutamate $(30{\mu}M)$ and N-methyl-D-aspartate(NMDA, $30{\mu}M)$ induced inward currents of $117{\pm}12.4$ pA(n=5) and $49{\pm}6.9$ pA(n=3), respectively. Glycine $(1{\mu}M)$ potentiated glutamate-induced currents $4{\sim}5$ times and NMDA-induced currents $8{\sim}10$ times. In addition, glycine $(30{\mu}M)$ induced Inward current ($31{\pm}6.1$ nA, n=2), which was rapidly desensitized after the peak to a new steady-state level. However, the inward currents induced by ${\gamma}-amino$ butyric acid(GABA, $1{\mu}M$) decreased continuously after the peak($226{\pm}41.6$ pA, n=3) under the similar experimental condition. The ionic currents and pharmacological responses of isolated neurons in this work were similar to those observed in vivo or in vitro spinal cord slice, indicating that acutely isolated neurons could be effectively used for further pharmacological studies.

• 한국재료학회지
• /
• 제23권3호
• /
• pp.161-167
• /
• 2013

The ZnO thin films were grown on GaN template substrates by RF magnetron sputtering at different RF powers and n-ZnO/p-GaN heterojunction LEDs were fabricated to investigate the effect of the RF power on the characteristics of the n-ZnO/p-GaN LEDs. For the growth of the ZnO thin films, the substrate temperature was kept constant at $200^{\circ}C$ and the RF power was varied within the range of 200 to 500W at different growth times to deposit films of 100 nm thick. The electrical, optical and structural properties of ZnO thin films were investigated by ellipsometry, X-ray diffraction (XRD), atomic force microscopy (AFM), photoluminescence (PL) and by assessing the Hall effect. The characteristics of the n-ZnO/p-GaN LEDs were evaluated by current-voltage (I-V) and electroluminescence (EL) measurements. ZnO thin films were grown with a preferred c-axis orientation along the (0002) plane. The XRD peaks shifted to low angles and the surface roughness became non-uniform with an increase in the RF power. Also, the PL emission peak was red-shifted. The carrier density and the mobility decreased with the RF power. For the n-ZnO/p-GaN LED, the forward current at 20 V decreased and the threshold voltage increased with the RF power. The EL emission peak was observed at approximately 435 nm and the luminescence intensity decreased. Consequently, the crystallinity of the ZnO thin films grown with RF sputtering powers were improved. However, excess Zn affected the structural, electrical and optical properties of the ZnO thin films when the optimal RF power was exceeded. This excess RF power will degrade the characteristics of light emitting devices.

• Bulletin of the Korean Chemical Society
• /
• 제29권5호
• /
• pp.928-932
• /
• 2008

A glassy carbon electrode (GCE) modified with poly(p-aminobenzene sulfonic acid) [Poly(p-ABSA)] film is fabricated by voltammetric technique in phosphate buffer solution (pH 8.0) containing $5.0\;{\times}\;10^{-3}\;mol\;L^{-1}$p- ABSA. Electrochemical behaviors of tryptophan at the Poly(p-ABSA) film electrode are investigated with voltammetry. The results indicate that the electrochemical response of tryptophan is improved significantly in the presence of poly(p-ABSA) film. Compared with the bare glassy carbon electrode, the Poly(p-ABSA) film electrode remarkably enhances the irreversible oxidation peak current of tryptophan. Some parameters such as voltammetric sweeping segments for the electrochemical polymerization, pH, accumulation potential and accumulation time are optimized. Under the optimal conditions, the oxidation peak current is proportional to tryptophan concentration in the range of $1.0\;{\times}\;10^{-7}$ to $1.0\;{\times}\;10^{-6}\;mol\;L^{-1}$, and $2.0\;{\times}\;10^{-6}$ to $1.0\;{\times}\;10^{-5}\;mol\;L^{-1}$ with a detection limit of $7.0\;{\times}\;10^{-8}\;mol\;L^{-1}$. The proposed procedure is successfully applied to the determination of tryptophan in a commercial amino acid oral solution.

• Corrosion Science and Technology
• /
• 제8권4호
• /
• pp.143-147
• /
• 2009

In biomedical implants and dental fields, titanium has been widely utilized for excellent corrosion resistance and biocompatibility. However, Ti and its alloys are nonbioactive after being implanted in bone. In this study, for the purpose of improvement in biocompatibility the anodic $TiO_2$ layer on Ti-xNb alloys were fabricated by electrochemical method in phosphate solution, and the effect of Nb content on the pore size, the morphology and crystallinity of Ti oxide layer formed by the anodic oxidation method was investigated. The Ti containing Nb up to 3 wt%, 20 wt% and 40 wt% were melted by using a vacuum furnace. The sample were cut, polished, and homogenized for 24 hr at $1050^{\circ}C$ for surface roughness test and anodizing. Titanium anodic layer was formed on the specimen surface in an electrolytic solution of 1 M phosphoric acid at constant current densities ($30mA/cm^2$) by anodizing method. Microstructural morphology, crystallinity, composition, and surface roughness of oxide layer were observed by FE-SEM, XRD, EDS, and roughness tester, respectively. The structure of alloy was changed from $\alpha$-phase to $\beta$-phase with increase of Nb content. From XRD results, the structure of $TiO_2$ formed on the Ti-xNb surface was anatase, and no peaks of $Nb_2O_5$ or other Nb oxide were detected suggesting that Nb atoms are dispersed in $TiO_2$-based solid solution. Surface roughness test and SEM results, pore size formed on surface and surface roughness decreased as Nb content increased. From the line analysis results, intensity of Ti peak was high in the center of pore, whereas, intensity of O peak was high in the outside of pore center.