• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2005년도 ICCAS
• /
• pp.237-240
• /
• 2005

A novel current mode high Q bandpass filter with electronically tuable values of Q based on second generation current controlled conveyor CCCIIs is presented. The circuit offers the advantages of using a few passive elements. The center frequency and pole-Q can be independently adjusted by via dc bias current of CCCIIs, It is shown from SPICE simulation that the results agree well with theoretical analysis

• 전자공학회논문지D
• /
• 제34D권10호
• /
• pp.14-23
• /
• 1997

An MMIC downconverting mixer for cellular phone application has been successfully developed using an MMIC process including $1 \mu\textrm{m}$ ion implanted gaAs MESFET and passive lumped elements consisting of spiral inductor, $Si_3N_4$ MIM capacitor and NiCr resistor. The configuration of the mixer presented in this paper is single-ended dual-gate FET mixer with common-source self-bias circuits for single power supply operation. The dimension of the fabricated circuit is $1.4 mm \times 1.03 mm $ including all input matching circuits and a mixing circuit. The conversion gian and noise figure of the mixer at LO powr of 0 dBm are 5.5dB and 19dB, respectively. The two-tone IM3 characteristics are also measured, showing -60dBc at RF power of -30dBm. Allisolations between each port show better than 20dB.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 F
• /
• pp.2795-2797
• /
• 1999

Several power factor correction(PFC) circuits are presented to achieve high PF electronic ballast for both voltage-fed and current-fed electronic ballast. The proposed PFC circuits use valley-fill(VF) type DC-link stages modified from the conventional VF circuit to adopt the charge pumping method for PFC operations during the valley intervals. In voltage-fed ballast, charge pump capacitors are connected with the resonant capacitors. In current-fed type, the charge pump capacitors are connected with the additional secondary-side of the power transformer. The measured PF and THD are higher than 0.99 and 15% for all proposed PFC circuits. The lamp current CF is also acceptable in the proposed circuits. The proposed circuit is suitable for implementing cost-effective electronic ballast.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 F
• /
• pp.2559-2561
• /
• 1999

The life of a fluorescent lamp is greatly affected by starting scenario and crest factor. This paper will propose a new crest factor control method in electronic ballast for fluorescent lamp using Pulse Frequency Modulation (PFM), which employs a passive Power Factor Correction (PFC) circuit in the input stage. The operation of parellel-loaded circuit, the switching frequency. and the characteristics of electronic ballast with the proposed PFM control scheme are described in detail, and its validity is verified by the simulation results.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2002년도 ITC-CSCC -2
• /
• pp.747-750
• /
• 2002

A circuit building block for realizing a continuous-time active-only current-mode integrator is presented. The proposed integrator is composed only of internally compensated type operational amplifier (OA) and operational transconductance amplifiers (OTAs). The integrator is suitable for integrated circuit implementation in either bipolar or CMOS technologies, since it does not require any external passive elements. Moreover, the integrator gain can be tuned through the transconductance gains of the OTAs. Some application examples in the realization of current-mode network functions using the proposed current-mode integrator as an active element are also given.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2001년도 하계종합학술대회 논문집(2)
• /
• pp.181-184
• /
• 2001

A coplanar waveguide(CPW) on a dielectric substrate consists of a center strip conductor with semi-infinite ground planes on either side. This type of waveguide offers several advantages over microstrip line. It facilitates easy shunt as well as series mounting of active and passive devices. It eliminates the need for wraparound and via holes, and it has a low radiation loss. These, as well as several other advantages, make CPW ideally suited for microwave integrated circuit applications. However, very little information is available in the literature on models for CPW discontinuities. This lack of sufficient discontinuity models for CPW has limited the application of CPW in microwave circuit design. We presented for the characteristics of coplanar waveguide open end capacitance and series gap capacitance. Measurements by utilizing the resonance method were made and the experimental data confirmed the validity of theories. The relationships between the CPW capacitances and the physical dimensions were studied.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 추계학술대회 논문집 학회본부
• /
• pp.435-437
• /
• 1997

In order to develop the three phase GTO CSI with double recovery path of commutation energy by passive devices (LCD), we studied the clamping circuit to protect switching device and energy recovery circuit to recover absorbed energy of capacitor and DC link inductor. In this paper, we investigated how DC input power is increased or decreased according to energy recovery path with or not in the three phase GTO current source inverter. We used a induction motor as the load of inverter, and controlled a induction motor with V/F constant control. Experimental results show that dissipated DC power is decreased and capacitor voltage Vc is effectively suppressed by double recovery path.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2002년도 전력전자학술대회 논문집
• /
• pp.746-749
• /
• 2002

This paper presents a new control method for the high frequency electronic ballast which is operated with raw rectified dc link using diode bridge. For the commercial electronic ballast, proper ac input power factor and crest factor of the lamp current are required. The most ballast, therefore, has a active or passive power factor collection (PFC) circuit. With the proposed method, it can be achieved simultaneously that grater than 0.9 of input power factor and less than 1.85 of lamp current crest factor without any PFC circuit. In this paper, the proposed ballast control scheme and the experimental results for the application to the fluorescent lamp are described.

• Journal of Power Electronics
• /
• 제9권2호
• /
• pp.180-187
• /
• 2009

When converters operate in megahertz range, the passive components and magnetic devices generate high losses. However, the eddy current issues and choices of magnetic cores significantly affect on the design stage. Apart from that, the components' reduction, miniaturization technique and frequency scaling are required as well as improvement in thermal capability, integration technique, circuit topologies and PCB layout optimization. In transformer design, the winding and core losses give great attention to the design stage. From simulation work, it is found that E-25066 material manufactured by AVX could be the most suitable core for high frequency transformer design. By employing planar geometry topology, the material can generate significant power loss savings of more than 67% compared to other materials studied in this work. Furthermore, young researchers can use this information to develop new approaches based on concepts, issues and methodology in the design of magnetic components for high frequency applications.

• Journal of Electrical Engineering and Technology
• /
• 제9권1호
• /
• pp.197-204
• /
• 2014

In this paper an Improved Zero Voltage Zero Current Pulse Width Modulation Forward converter which employs a simple resonance snubber circuit is introduced. A simple snubber circuit consists of a capacitor, an inductor and two diodes. In proposed converter, switch Q1 operates at ZCS turn-on, and ZVS turn-off conditions and all-passive semiconductor devices operate at ZVZCS turn-on and turn-off state. The proposed converter is analyzed and various operating modes of the ZVZCS-PWM forward converter are discussed. Analysis and design considerations are presented and the prototype experimental results of a 100w (40 V/2.5A) proposed converter operating at 30 KHz switching frequency confirm the validity of theoretical analysis.