• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.85-85
• /
• 2007

최근 귀금속중의 하나인 Ruthenium(Ru)은 높은 일함수, 누설전류에 대한 높은 저항성등의 톡성으로 인해 캐패시터의 하부전극으로 각광받고 있다. 하부전극으로 증착된 Ru은 일반적으로 각 캐패시터의 분리와 평탄화를 위해 건식식각이 이루어진다. 하지만, 건식식각 공정중 유독한 $RUO_4$ 가스가 발생할 수 있으며, 불균일한 캐패시터 표면을 유발할 수 있다. 이러한 문제점들을 해결하기 위해 CMP 공정이 필요하게 되었다. 하지만, Ru은 화학적으로 매우 안정하기 때문에 Ru CMP 슬러리에 대한 연구가 필요하게 되었으며, 이에 대한 연구가 활발히 진행되고 있다. 본 연구에서는 Ru CMP 공정에서 Chemical A가 에칭제 및 산화제로 사용된 슬러리의 pH 변화와 pH 적정제에 따른 영향을 살펴보았다. Ru wafer를 이용하여 static etch rate, passivation film thickness와 wettability를 pH와 pH 적정제에 따라 비교해 보았다. 또한, pH 적정제로 $NH_4OH$와 TMAH를 이용하여 pH별 슬러리를 제작하고 CMP 공정을 실시하여 Ru의 removal rate을 측정하였다. $NH_4OH$와 TMAH의 경우 각각 130. 100 nm/min의 연마율이 측정된 pH 6에서 가장 높은 연마률을 보였으며, TMAH의 경우가 pH 전 구간에서 $NH_4OH$에 비해 낮은 연마율이 측정되었다. TEOS 에 대한 Ru의 선택비를 측정해 본 결과, $NH_4OH$의 경우 pH 8~9. TMAH의 경우 pH 6~7에서 높은 selectivity를 얻을 수 있었다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.171-171
• /
• 2010

GaN 기반 Light emitting diodes(LEDs)의 p-type doping layer는 일반적으로 hole을 발생시키는 acceptor로 Mg이 사용하되고 있다. 보통 Mg이 도핑된 p-type GaN은 >$1\;{\Omega}{\cdot}cm$의 저항이 존재하는데 그 이유는 Mg의 열적 이온화를 위한 activation 에너지가 높아서 상온에서 valence band의 hole concentration는 전체 억셉터 농도의 1%가 되지 않기 ��문이다. 본 논문에서는 높은 hole 농도를 얻기 위해서 metalorganic chemical-vapor deposition (MOCVD)를 장비를 사용하여 사파이어 기판의 misorientation-angle에 따른 p-type a-plane(11-20) GaN 특성을 분석하였다. misorientation-angle은 c축 방향으로 $+0.15^{\circ}$, $-0.15^{\circ}$, $-0.2^{\circ}$, $-0.4^{\circ}$ off된 r-plane(1-102) 사파이어 기판 을 사용하였다. p-type 도핑물질로 bis-magnesium (Cp2Mg) 소스를 사용하였고 성장 과정중 발생하는 hydrogen passivation으로 인한 Mg-H complexes현상을 해결하기위해 conventional furnace annealing (CFA)와 rapid thermal annealing (RTA)를 이용하여 열처리 공정을 진행하였다. 열처리 공정은 Air와 N2 분위기에서 $650^{\circ}C$에서 $900^{\circ}C$ 사이의 다양한 온도에서 수행하였고 Hall 측정을 위해 Ni을 전극 물질로 사용하였다. 상온에서 Accent HL5500IU Hall system을 사용하여 hole concentration, mobility, specific resistance을 측정하였다. 열처리 공정 후 Hall측정 결과 $+0.15^{\circ}$, $-0.15^{\circ}$, $-0.2^{\circ}$, $-0.4^{\circ}$ off된 각 샘플들은 온도, 시간, 분위기에 따라 hole concentration ($7.4{\times}10^{16}cm^{-3}{\sim}6{\times}10^{17}cm^{-3}$), mobility(${\mu}h=\;1.72\;cm^2/V-s\;{\sim}15.2\;cm^2/V-s$), specific resistance(4.971 ohm-cm ~8.924 ohm-cm) 가 변화됨을 확인 할 수 있었다. 또한 광학적 특성을 분석하기 위해 Photoluminescence (PL)을 측정하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.494-497
• /
• 2004

본 연구는 방사선 영상센서 적용을 위한 $HgI_2$ 필름의 특성 평가에 관한 것으로서 X-선 조사조건별 인가전압에 따른 검출신호 특성을 조사하였다. 기존의 $HgI_2$ 검출기의 경우 신호량이 크다는 장점이 있으나 노이즈의 양이 크다. 이에 대한 해결책으로 보호층을 삽입하나 이 경우 X-선 조사에 따른 시간 응답 특성이 있어서 전하트랩현상(tailing effect)에 의한 영향이 크게 존재하였다. 따라서 본 논문에서는 이러한 문제점을 해결하고자 보호층으로써 a-Se 을 삽입하여 기존의 $HgI_2$ 검출기에서 사용되어지는 parlyene이 삽입된 검출기와 전기적 특성을 측정, 비교해보고자 한다. 제작방식으로는 대면적 제작이 용이한 스크린 프린팅 방식을 이용하여 두께 $140\;{\mu}m$와 $3\;cm\;{\times}\;2\;cm$ 면적으로 제조하였다. 측정결과, a-Se을 보호층으로 사용한 $HgI_2$ 필름이 민감도는 거의 비슷하나 누설전류가 안정화 되는데 걸리는 감소시간(decay time)이 parlyene을 사용한 구조에 비해 훨씬 낮았다. 또한 X선에 대한 민감도는 기존의 a-Se에 비해 월등히 높아 적은 방사선 조사량(radiation dose)에서도 신호검출이 가능하여 저선량이 요구되는 방사선 투시촬영(digital fluoroscopy) 적용에 유용할 것으로 기대된다.

• Journal of the Semiconductor & Display Technology
• /
• v.17 no.3
• /
• pp.41-45
• /
• 2018

Two-dimensional (2D) materials have been studied extensively due to their excellent physical, chemical, and electrical properties. Among them, we report the material and device characteristics of tin disulfide ($SnS_2$). To apply $SnS_2$ as a channel layer in a transistor, $SnS_2$ channels were formed by a stripping method and a transfer method. The limitation of this method is that it is difficult to produce uniform device characteristics over a large area. Therefore, we directly deposited $SnS_2$ by atomic layer deposition (ALD) and then performed lithography. This method was able to produce devices with repeatable characteristics over a large area. However, the $SnS_2$ film was damaged by the acetone used as a photoresist (PR) developer during the lithography process, with the electrical properties of mobility of $2.6{\times}10^{-4}cm^2/Vs$, S.S. of 58.1 V/decade, and on/off current ratio of $1.8{\times}10^2$. These results are not suitable for advanced electronic devices. In this study, we analyzed the effect of acetone on $SnS_2$ and studied the device process to prevent such damage. Using polyvinyl alcohol (PVA) as a passivation layer during the lithography process, the electrical characteristics of the $SnS_2$ transistor had $2.11{\times}10^{-3}cm^2/Vs$ of mobility, 11.3 V/decade of S.S, and $2.5{\times}10^3$ of the on/off current ratio, which were 10x improvements to the $SnS_2$ transistor fabricated by the conventional method.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.27 no.1
• /
• pp.187-192
• /
• 2021

In this study, Inconel 625 was used as a thermal spray material to prevent dew point corrosion damage to the economizer tube, and sealing treatment was performed after applying the arc thermal spray coating technology. Various electrochemical experiments were conducted in the 0.5 wt% sulfuric acid solution to analyze the corrosion resistance of the thermal spray coating (TSC) layer. After the anodic polarization experiment, the degree of corrosion damage was determined through a scanning electron microscope and EDS component analysis. When measuring the open circuit potential, the effect of the sealing treatment was confirmed through stable potential formation of the TSC+sealing treatment (TSC+Sealing). As a result of the anodic polarization experiment, the passivation region was confirmed in TSC and TSC+Sealing, and corrosion resistance was improved as no corrosion damage was observed. In addition, the corrosion resistance of TSC+Sealing was the best when analyzing the corrosion potential and corrosion current density calculated by Tafel analysis.

• Current Photovoltaic Research
• /
• v.9 no.4
• /
• pp.128-132
• /
• 2021

Advances in screen printing technology have been led to development of high efficiency silicon solar cells. As a post PERx structure, an n-type wafer-based rear side TOPCon structure has been actively researched for further open-circuit voltage (Voc) improvement. In the case of the metal contact of the TOPCon structure, the poly-Si thickness is very important because the passivation of the substrate will be degraded when the metal paste penetrates until substrate. However, the thin poly-Si layer has advantages in terms of current density due to reduction of parasitic absorption. Therefore, poly-Si thickness and firing temperature must be considered to optimize the metal contact of the TOPCon structure. In this paper, we varied poly-Si thickness and firing peak temperature to evaluate metal induced recombination (Jom) and contact resistivity. Jom was evaluated by using PL imaging technique which does not require both side metal contact. As a results, we realized that the SiN_x deposition conditions can affect the metal contact of the TOPCon structure.

• Journal of Electrochemical Science and Technology
• /
• v.13 no.2
• /
• pp.213-226
• /
• 2022

In the present study, the corrosion behavior of aluminum Al-7075 tempered (T-6 condition) alloy was evaluated by immersion testing and electrochemical testing in 1.75% and 3.5% NaCl environment at acidic, neutral and basic pH. The data obtained by both immersion tests and electrochemical corrosion tests (potentiodynamic polarization and electrochemical impedance spectroscopy tests) present that the corrosion rate of the alloy specimens is minimum for the pH=7 condition of the solution due to the formation of dense and well adherent thin protective oxide layer. Whereas the solutions with acidic and alkaline pH cause shift in the corrosion behavior of aluminum alloy to more active domains aggravated by the constant flux of acidic and alkaline ions (Cl^- and OH^-) in the media which anodically dissolve the Al matrix in comparison to precipitated intermetallic phases (cathodic in nature) formed due to T6 treatment. Consequently, the pitting behavior of the alloy, as observed by cyclic polarization tests, shifts to more active regions when pH of the solutions changes from neutral to alkaline environment due to localized dissolution of the matrix in alkaline environment that ingress by diffusion through the pores in the oxide film. Microscopic analysis also strengthens the results obtained by immersion corrosion testing and electrochemical corrosion testing as the study examines the corrosion behavior of this alloy under a systematic evaluation in marine environment.

• Analytical Science and Technology
• /
• v.19 no.5
• /
• pp.394-399
• /
• 2006

The polishing performance and the relationships of electrochemistry depending upon oxidizers and additives in the tungsten CMP slurry used in semiconductor industry were investigated. Hydrogen peroxide, ferric nitrate and potassium iodate were used as oxidizers and they showed different oxidation reactions on tungsten film depending on the kind of oxidizers and pH of slurry. The differences influenced the polishing performance. Etching reaction was predominated in the hydrogen peroxide. However, passivation reaction was prevailed in ferric nitrate and potassium iodate. TMAH and KOH raised the potential energy and removal rate of tungsten, and improved a dispersion characteristic of slurry by increasing absolute value of zeta potential. Addition of 100 ppm of poly(acrylic acid) of M.W. 250,000 improved dispersion ability.

• Journal of Adhesion and Interface
• /
• v.21 no.3
• /
• pp.107-112
• /
• 2020

Recently, the atomically thin transition-metal dichalcogenide (TMD) semiconductors have attracted much attention owing to their remarkable properties such as tunable bandgap with high carrier mobility, flexibility, transparency, etc. However, because these TMD materials have a significant drawback that they are easily degraded in an ambient environment, various attempts have been made to improve chemical stability. In this research article, I report a method to improve the air stability of WSe₂ one of the TMD materials via surface passivation with an h-BN insulator, and its application to field-effect transistors (FETs). With a modified hot pick-up transfer technique, a vertical heterostructure of h-BN/WSe₂ was successfully made, and then the structure was used to fabricate the top-gate bottom-contact FETs. The fabricated WSe₂-based FET exhibited not only excellent air stability, but also high hole mobility of 150 ㎠/Vs at room temperature, on/off current ratios up to 3×10⁶, and 192 mV/decade of subthreshold swing.

• Journal of Technologic Dentistry
• /
• v.30 no.1
• /
• pp.25-31
• /
• 2008

Cp-Ti and Ti-6Al-4V alloys commonly used dental implant materials, particularly for orthopaedic and osteosynthesis because of its suitable mechanical properties and excellent biocompatibility. This alloys have excellent corrosion behavior in the clinical environment. The first factor to decide the success of dental implantation is sufficient osseointegration and high corrosion resistance between on implant fixture and its surrounding bone tissue. In this study, in order to increase corrosion resistance and biocompatibility of Cp-Ti and Ti-6Al-4V alloy that surface of manufactured alloy was coated with TiN by RF-magnetron sputtering method. The electrochemical behavior of TiN coated Cp-Ti and Ti-6Al-4V alloy were investigated using potentiodynamic (EG&G Co, PARSTAT 2273. USA) and potentiostatic test (250mV) in 0.9% NaCl solution at 36.5 $\pm$ 1$^{\circ}C$. These results are as follows : 1. From the microstructure analysis, Cp-Ti showed the acicular structure of $\alpha$-phase and Ti-6Al-4V showed the micro-acicular structure of ${\alpha}+{\beta}$ phase. 2. From the potentiodynamic test, Ecorr value of Cp-Ti and Ti-6Al-4V alloys showed -702.48mV and -319.87mV, respectively. Ti-6Al-4V alloy value was higher than Cp-Ti alloy. 3. From the analysis of TiN and coated layer, TIN coated surface showed columnar structure with 800 nm thickness. 4. The corrosion resistance of TiN coated Cp-Ti and Ti-6Al-4V alloys were higher than those of the non-coated Ti alloys in 0.9% NaCl solution from potentiodynamic test, indicating better protective effect. 5. The passivation current density of TiN coated Cp-Ti and Ti-6Al-4V alloys were smaller than that of the noncoated implant fixture in 0.9% NaCl solution, indicating the good protective effect resulting from more compact and homogeneous layer formation.