• Macromolecular Research
• /
• v.17 no.12
• /
• pp.969-975
• /
• 2009

This article describes the topical delivery and localization of budesonide through the hairless mouse skin. Two poly(ethylene oxide)-block-poly($\varepsilon$-caprolactone)-block-poly(ethylene oxide) (PEO-PCL-PEO) triblock copolymers (T 222 and T 252) having different CL:EO ratios were added in the preparation of budesonide particles stabilized with poly(vinyl alcohol) (PVA) and Tween 80 under ultrasonication. For comparison, a commercial PEO-PPO-PEO triblock copolymer (F68) was studied under the same condition. To demonstrate the effects of the triblock copolymer, the particle size of budesonide emulsion, entrapment efficiency, and in vitro release were measured and compared. The budesonide particles stabilized by the triblock copolymers had a diameter of ca. 350 nm with entrapment efficiencies of 66-76%. The In vitro release profiles of all samples showed an initial burst followed by sustained release. The skin penetration and permeation of budesonide were analyzed by using a Frantz diffusion cell. T 222 and T 252 exhibited higher total permeation amounts, but lower budesonide penetration amounts, than F68. The results suggest that the partitioning of budesonide in each skin layer can be adjusted in order to avoid skin thinning and negative immune response arising from the penetration of budesonide in blood vessels.

• Journal of ILASS-Korea
• /
• v.13 no.4
• /
• pp.212-219
• /
• 2008

To develop the twin-fluid atomizer having the excellent performance of painting, the spray characteristics of how a wide area can be painted efficiently by one time spraying were studied in this paper. Spray phenomena are affected by the many factors determining the spray field such as the spraying pressure of gas, the spraying pressure and viscosity of liquid paints, the opening duration of needle valve, the design dimension of nozzle, and so on. As the results of experiments, these factors affecting on spray characteristics were suggested as followings; 1) The optimum spraying pressure of gas was $0.015{\sim}0.02\;kPa$, and the appropriate spraying pressure of liquid paint was 0.01kPa, In these situations, the setting up pressures must be compensated as much as the losing amount of pressure because a decompression occurred when operating valves. 2) The duration of opening the needle valve must be sustained for $1{\sim}2$ seconds to inject gas after spraying the liquid paint. This operating of the needle valve was necessary to avoid the affect on the changing of liquid column length, and to prevent the droplet deposit at the initial time of spraying. 3) The spray tip penetration was gained form the experimental equation, and the effective spraying angle was $85^{\circ}{\pm}5^{\circ}$ just at he appropriate spraying pressure of gas. The distribution of the area sprayed had the variation in $350{\pm}50\;mm$ because of the spraying pressure of gas, the its distance from the spray tip, and the lift of the needle valve.

• Journal of the Microelectronics and Packaging Society
• /
• v.8 no.1
• /
• pp.5-11
• /
• 2001

Melting behavior and bridge phenomenon of solder paste, which is essential for surface mount technology in pachaging, were investigated. Solder paste of Sn-37%Pb was printed on Cu-pattern of PCB, and heated over melting point. Melting behavior of the paste was observed using CCD-camera. In order to modelize the melting and agglomeration phenomena of paste, two solder balls of 0.76 mm diameter were used. As experimental results, the paste start to melt from the margin of the printed shape. The height of the melted paste decreased from 270 $\mu\textrm{m}$ to 200 $\mu\textrm{m}$ firstly, and finally recovered to 250 $\mu\textrm{m}$ During the melting procedure, pores were evolved from the molted paste. Concerning melting model of solder ball, relationship between contact area of solder ball and soldering time was derived as $\chi^2/t=4r \; \gamma/\eta=7.56 m^2$/s at $280^{\circ}C$.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.8
• /
• pp.2671-2676
• /
• 2011

Nanocrystalline $TiO_2$ spherical particle (NP) with a dimension of 5 ${\times}$ 5.5 nm and several nanorods (NR) with different aspect ratios (diameter ${\times}$ length: 5 ${\times}$ 8.5, 4 ${\times}$ 15, 4 ${\times}$ 18 and 3.5 ${\times}$ 22 nm) were selectively synthesized by a solvothermal process combined with non-hydrolytic sol-gel reaction. With varying the molar ratio of TTIP to oleic acid from 1:1 to 1:16, the NRs in the pure anatase phase were elongated to the c-axis direction. The prepared NP and NRs were applied for the formation of nanoporous $TiO_2$ layers in dye-sensitized solar cell (DSSC). Among them, NR2 ($TiO_2$ nanorod with 4 ${\times}$ 15 nm) exhibited the highest cell performance: Its photovoltaic conversion efficiency (${\eta}$) of 6.07%, with $J_{sc}$ of 13.473 mA/$cm^2$, $V_{oc}$ of 0.640 V, and FF of 70.32%, was 1.44 times that of NP with a size of 5 ${\times}$ 5.5 nm. It was observed from the transient photoelectron spectroscopy and the incident photon to current conversion efficiency (IPCE) spectra that the $TiO_2$ films derived from NR2 demonstrate the longest electron diffusion length ($L_e$) and the highest external quantum efficiency (EQE).

• Progress in Medical Physics
• /
• v.30 no.4
• /
• pp.112-119
• /
• 2019

Purpose: The advantages of ocular proton therapy are that it spares the optic nerve and delivers the minimal dose to normal surrounding tissues. In this study, it developed a solid eye phantom that enabled us to perform quality assurance (QA) to verify the dose and beam range for passive single scattering proton therapy using a single phantom. For this purpose, a new solid eye phantom with a polymethyl-methacrylate (PMMA) wedge was developed using film dosimetry and an ionization chamber. Methods: The typical beam shape used for eye treatment is approximately 3 cm in diameter and the beam range is below 5 cm. Since proton therapy has a problem with beam range uncertainty due to differences in the stopping power of normal tissue, bone, air, etc, the beam range should be confirmed before treatment. A film can be placed on the slope of the phantom to evaluate the Spread-out Bragg Peak based on the water equivalent thickness value of PMMA on the film. In addition, an ionization chamber (Pin-point, PTW 31014) can be inserted into a hole in the phantom to measure the absolute dose. Results: The eye phantom was used for independent patient-specific QA. The differences in the output and beam range between the measurement and the planned treatment were less than 1.5% and 0.1 cm, respectively. Conclusions: An eye phantom was developed and the performance was successfully validated. The phantom can be employed to verify the output and beam range for ocular proton therapy.

• Journal of Environmental Science International
• /
• v.20 no.1
• /
• pp.147-153
• /
• 2011

The objectives of this study were to investigate the seasonal characteristics of metallic and ion elements of $PM_{10}$(Particulate matter with aerodynamic diameter ${\leq}10\;{\mu}m$) and the effects of vessels exhaust emission from ships harboring in Busan City. The $PM_{10}$ samples were collected from January 2010 to October 2010 at Dongsam-dong(coastal area), in Busan City. The particulate matters were analyzed for major water soluble ionic components and metals. The ranges of the $PM_{10}$ mass concentrations were from 29.8 ${\mu}g/m^3$ to 47.0 ${\mu}g/m^3$ in Dongsam-dong. The $PM_{10}$ mass concentrations in Dongsam-dong are very similar to Gwangbok-dong during same sampling periods. These results were understood by the effects of the shipping source emitted from ships anchoraging and running. The concentrations of water-soluble ions and metals in the $PM_{10}$ had a level of as high as the order of $SO_4^{2-}$>$NO_3^-$>$Cl^-$ and $NH_4^+$>$Na^+$>$Ca^{2+}$>$K^+$>$Mg^{2+}$, respectively. The correlation coefficients($R^2$) for $SO_4^{2-}/PM_{10}$ and $NH_4^+/PM_{10}$ of were 0.7446 and 0.7784, respectively, and it showed the high correlation with each other.

• The Journal of Advanced Prosthodontics
• /
• v.10 no.3
• /
• pp.205-210
• /
• 2018

PURPOSE. The purpose of this study was to evaluate the efficiency of a gas-phase fluorination method under different fluorination periods through using two resin cements. MATERIALS AND METHODS. 84 zirconia specimens in dimensions of $5mm{\times}5mm{\times}2mm$ were prepared and surface treated with $50{\mu}m$ aluminum oxide particles or gas phase fluorination for 2 min, 5 min, or 10 min. One specimen in each group was surface analyzed under scanning electron microscope. The remaining specimens were bonded to composite cylinders in dimensions of 2 mm diameter and 3 mm high with Panavia SA Plus or Variolink N. Then, the specimens were stored in $37^{\circ}C$ distilled water for 24 hours and shear bond strength test was applied at a speed of 1 mm/min. RESULTS. The highest shear bond strength values were observed in the samples fluorinated for 5 minutes and cemented with Panavia SA Plus. Variolink N did not elicit any statistical differences between surface treatments. Panavia SA Plus resin cement and Variolink N resin cements featured statistically significant difference in shear bond strength values only in the case of 5 minutes of fluorination treatment. CONCLUSION. According to the results of this study, application of 5 minutes of fluorination with 10-methacryloyloxydecyl dihydrogen phosphate monomer (MDP) containing Panavia SA Plus resin cement increased the resin bond strength of zirconia. Fluorination of the zirconia surface using conventional resin cement, Variolink N, did not lead to an increase in bond strength.

• Korean Chemical Engineering Research
• /
• v.43 no.4
• /
• pp.482-486
• /
• 2005

The biodegradable poly(${\varepsilon}$-caprolactone)(PCL)/poly(ethylene imine)(PEI) microcapsules containing $Al_2O_3$ and fragrant oil were prepared with different PEI contents. The effects of stirring rate and concentration of the surfactant on the diameter and morphologies of microcapsules were investigated by using scanning electron microscope (SEM). Thermal behaviors were studied by using a differential scanning calorimetry(DSC), and the release behaviors of fragrant oil from microcapsule were characterized by UV/vis. spectrophotometer. As a result, the average particle size of the microcapsules decreased with increasing the stirring rate or concentration of the surfactant. The surface morphologies of the microcapsules were changed from smooth surfaces to skin-like rough surfaces as increasing the PEI content. These results were mainly due to the increased hydrophilic groups at the microcapsule surfaces, resulting in increasing the release rate of fragrant oil in the microcapsules studied.

• Korean Chemical Engineering Research
• /
• v.43 no.4
• /
• pp.511-516
• /
• 2005

In this work, the crosslinked-chitosan microcapsules containing fragrant oil were prepared by oil-in-water-in-oil (O/W/O) multi-emulsion method. The effects of concentration of fragrant oil and stirring rates on the preparing of the microcapsules were investigated. The diameter and form of the microcapsules were observed by scanning electron microscope (SEM). As a result, the average particle size of microcapsules was decreased with increasing the stirring rate. The formation of chitosan microcapsules was comfirmed by FT-IR. The inclusion of fragrant oil into chitosan microcapsules was determined in the presence of specific peak of fragrant oil, i.e., $1,460cm^{-1}$, $2,960cm^{-1}$. Also, the release behavior or profile of fragrant oil from chitosan microcapsules was examined with UV/vis spectra. Released amounts of fragrant oil were increased with increasing as the content of fragrant oil and decreasing the pH.

• Fashion & Textile Research Journal
• /
• v.10 no.4
• /
• pp.552-559
• /
• 2008

Recent days, various inner wears, sheets and interior goods are manufactured using materials dyed with loess emphasizing its improved blood circulation, metabolism, anti-bacterial, deodorizing properties, and far-infrared ray emissions. The purpose of this study is to investigate the effect of chitosan treatment on the dyeing of cotton fabric using loess as colorants. Particle size of loess, the morphology and dyeability(K/S) of chitosan crosslinked cotton fabrics, and washing durability of loess dyed cotton fabric were investigated. In this study, cotton fabrics were treated with a crosslinking agent, epichlorohydrin, in the presence of chitosan to improve the dyeing properties of cotton fabrics with natural dye by the chemical linking of chitosan to the cellulose structure. This process was applied by means of the conventional mercerizing process. The results obtained were as follows; Mean average diameter of loess was $1.13{\mu}m$. According to various conditions, the optimum dyeing conditions for cotton fabrics pretreated by 1% chitosan treatment was where 10%(owb) of loess was applied at $90^{\circ}C$ for 120minutes, while for cotton fabrics without chitosan treatment was where 15%(owb) of loess was applied at $90^{\circ}C$ for 150minutes. Overall, K/S value of loess dyed cotton fabric pretreated with 1% chitosan was higher than that of cotton fabrics without chitosan treatment. The Color fastness, washing fastness and light fastness of loess were excellent as 4-5grade.