• Nuclear Engineering and Technology
• /
• v.29 no.4
• /
• pp.269-279
• /
• 1997

The errors associated with incorrect sampling and transport of radioactive aerosol from radwaste thermal process off-gas are analyzed and the conditions of representative sampling and correct transport of radioactive aerosol for off-gas system evaluation are discussed. An estimation method of sampling errors for individual radionuclides is proposed and applied to simulated vitrification melter aerosols. Prediction methods for particle deposition in sample transport tube under laminar as well as turbulent flow conditions are also described by example calculations with simulated incinerator off-gas From the results of example calculations and plots, instrumental and operational conditions of radioactive aerosol sampling system with minimized errors and correction methods for nonideal sampling and transport are recommended.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2001.03a
• /
• pp.445-452
• /
• 2001

Generally, OPC(ordinary portland cement) is used for grouting in Korea, and bentonite has usually been added to prevent the deposition of cement particles. The dispersion of CB(cement bentonite) grout is influenced by variable factors i.e. water to cement ratio, particle size of cement, kind of bentonite, adding volume, methods of adding, viscosity of CB grout materials and curdling time. Among variable factors, the viscosity of CB grout materials is influenced by the dispersion, and dispersion is improved as increasing the mixing speed. In this paper, described a suitable mixing speed of the High Speed Mixer in field, engineering characteristics of CB grout materials vary with the water to cement ratio and the mixing speed as well as confirming the state of dispersion.

• Proceedings of the KIEE Conference
• /
• 1995.11a
• /
• pp.453-455
• /
• 1995

In electrostatic airclean filter, the collection efficiency defends on particle charge in the ionizer section. The effect of electrostatic airclean filter condition (deposition of dust, variation of corona discharge current) on corona discharge characteristics was well studied. However, it seems not to be studied on corona discharge characteristics of electrostatic airclean filter respect to contaminated electrode which is caused by practical use. In this paper, Long-term(60days) effects are studied experimentally by two methods. The one is ozone concentration, the other is collection efficiency. Generation of ozone level was increased but collection efficiency was slightly reduced in long-term used electrostatic airclean filter.

• Journal of Pharmaceutical Investigation
• /
• v.19 no.1
• /
• pp.29-37
• /
• 1989

For the prevention of the aggregation during microencapsulation, the effects and role of polyisobutylene(PIB), as a protective colloid, were studied. The effects of sealant treatment on the microencapsulation were studied. Methyldopa was microencapsulated with ethylcellulose (EC) by polymer deposition from cyclohexane by temperature change using PIB. The EC-microencapsulated methyldopa was sealed with spermaceti. The dissolution of methyldopa was influenced by the drug to wall ratio. When PIB was used, low aggregation of microcapsules occurred and the surface was smooth with a few pores. Treatment of microcapsules with spermaceti retarded the release of methyldopa, the release being affected by the percentage of sealant used and the particle size of the product.

• Journal of the Korean Society of Combustion
• /
• v.7 no.2
• /
• pp.24-33
• /
• 2002

The morphology of deposits on $15-{\mu}m$ thin SiC filaments has been investigated with SEM in a co-flowing, propane/air laminar diffusion flame. The average size of mature soot particles deposited in the luminous flame edge is strongly dependent on their axial position in a typical heavily sooting flame. The surface growth of liquid-phase PAHs molecules and the transition to soots from fully-developed precursors could be observed in the radial deposition of the flame. Two sooting regimes were found: one is the transition from the condensed-phase precursors; the other is the aggregation of smaller soot particles (or chains of them) to be carried along particle path lines. In the high temperature flame edge outside the soot luminous flame surface, the very thin fiber-like structures, which are about 10 nm thick, were found.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1999.11a
• /
• pp.42-48
• /
• 1999

An experimental study was performed to discover the effect of environment on the tribological behavior of Si-incorporated diamond-like carbon(Si-DLC) film slid on a steel ball. The films were deposited on Si(100) wafers from radio-frequency glow discharge of mixtures of benzene and dilute silane gases. Experiments using a ball-on-disk test-rig was performed under vacuum, dry air and ambient air conditions. It was observed that coefficient of friction was decreased as the environmental condition changes from vacuum, to dry air. It was also observed that the coefficient of friction decreased with increasing silicon concentration in the film. Chemical analyses of debris suggested that the low and stable friction coefficient is closely related to the silicon rich oxide debris and the rolling action.

• Journal of the Korean Society of Visualization
• /
• v.7 no.2
• /
• pp.35-41
• /
• 2010

Supersonic microjets acquire considerable research interest from a fundamental fluid dynamics perspective, in part because the combination of highly compressible flow at low-to-moderate Reynolds number is not very common, and in part due to the complex nature of the flow itself. In addition, microjets have a great variety engineering applications such as micro-propulsion, MEMS(Micro-Electro Mechanical Systems) components, microjet actuators and fine particle deposition and removal. Numerical simulations have been carried out at moderate nozzle pressure ratios and for different nozzle exit diameters to investigate and to understand in-depth of aerodynamic characteristics of supersonic microjets.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.73-73
• /
• 2018

조직재생공학은 조직이나 장기를 재생하고 유지하는 데 초점을 맞춘 종합 분야이다. 세포담체는 세포가 조직이나 장기로 발달 할 수 있도록 결정적인 역할을 한다. 따라서 공극률, 기공 크기, 기공 상호 연결성, 표면 거칠기, 기계적 강도 및 기하학과 같은 기본 요구 사항들은 중요한 특성으로 간주된다. Particle leaching, phase separation, solvent casting, gas foaming, selective laser sintering, fused deposition 및 3D dispensing (printing)과 같은 다양한 Rapid Prototyping 방법이 세포담체 제조에 사용되었다. 또한, 다양한 천연 및 합성 고분자가 세포담체를 제조하는데 사용되어왔다. 본 연구에서는 기존의 3D 프린팅 방법과 플라즈마 에칭 공정을 이용하여 나노 에칭 된 나선형 가닥으로 구성된 3 차원 세포담체를 제작 하였다. 제작 된 세포담체의 물리적 및 생물학적 성질을 비교 연구하기 위해, 본 연구에서는 매끄러운 가닥을 대조물로 사용하였다. 나노 에칭된 표면은 초기 세포 부착, 증식 및 골 형성 분화와 같은 세포 활동에 영향을 미쳤다.

• Proceedings of the Korean Society of Laser Processing Conference
• /
• 2006.06a
• /
• pp.60-65
• /
• 2006

Previous studies demonstrated that laser ablation under transparent liquid can result in ablation enhacement and particle removal from the surface. In this work, the liquid-assisted excimer laser ablation process is examined fer polyethylene terephthalate (PET), polymethyl methacrylate (PMMA), Si, and alumina with emphasis on ablation enhacement, surface topography, and debris formation. In the case of PET and PMMA, the effect of liquid is analyzed both fer thin water film and bulk water. As the ablation enhanement by liquid is already known for Si and alumina, the analysis focuses on surface topography and debris formation resulting from the liquid-assisted laser ablation process. The results show that application of liquid increases the ablation rate of PMMA while that of PET remains unchanged even in the liquid-assisted process. It is also revealed that the liquid can significantly improve the surface quality by reducing the debris deposition. However, the surface roughness is generally deteriorated in the liquid-assisted process. The surface toporaphy is found to be strongly dependent on the method of liquid application, i.e., thin film or bulk liquid.

• Journal of the Korean Ceramic Society
• /
• v.31 no.3
• /
• pp.312-320
• /
• 1994

Effect of the laser shot number on the particulates density of the pulsed laser deposited YBa2Cu3O7-x thin films and the laser irradiated surface morphology of the YBa2Cu3O7-x bulk target have been investigated. Until 100 laser shots of cumulative irradiation, the films has the particulates density of ~103 mm-2. However, after 100 laser shots, the density was increased more than 10 times. This results has been explained by the change of particulate ejection path with the development of conical structure at the target surface.