• Journal of Adhesion and Interface
• /
• v.21 no.4
• /
• pp.143-155
• /
• 2020

Hydrophobic Organic-Inorganic (O-I) hybrid materials prepared by sol-gel process have been widely used at functional coating fields such as coatings for anti-corrosion, anti-icing, self-cleaning, anti-reflection. The key point for fabricating hydrophobic surface is to optimize the surface energy and roughness of the coating films. There are typical processes to control the surface energy and roughness which are 'In situ fabricating', 'Pre-fluorinating/Post-roughening', 'Pre-roughening/ Post-fluorinating'. In this study, particle-binder process was used for in-situ fabrication of hydrophobic coating films. Various O-I hybrid compounds prepared using several kinds of alkoxysilane compounds were used as a binder for silica nanoparticles at particle-binder process. To study effect of fluorine content and weight ratio of particle : binder on the hydrophobicity and surface morphology, Hydrophobic coating films were prepared onto glass substrate at various content of fluorine content of O-I hybrid binder and weight ratio of particle : binder. The coating films prepared using O-I hybrid binder (GPTi-HF10) having 10 wt% of fluorine content showed the highes water contact angle (107.52±1.6°). The coating films prepared at 1:3 weight ratio of GPTi-HF10 : silica nanoparticle exhibited the highest water contact angle (130.84±1.99°).

• Journal of Wetlands Research
• /
• v.9 no.3
• /
• pp.1-12
• /
• 2007

In this study, the correlation of organic content with particle size and type of sediment was found out.Particle size, stratigraphic section and organic content of sediments sampled from Dalpo wetland was analyzed. Dalpo wetland consists of three wetlands, and the area of Dalpo wetland is about $31,295m^2$. The particle size analyses for sampled sediments of 7 points (3 points in wetland A, 3 points in wetland B and 1 point in wetland C) were tested. As results of the particle size analyses, the sediment particle size becomes larger as to the edge of the wetland. It is revealed in order of wetland A > wetland C > wetland B. Borehole surveys with horizontal distance in the major and minor axes of wetland A, the major and minor axes of wetland B and the major axis of wetland C were accomplished. Clayey peat deposit is distributed at 10~90 cm depth below ground surface in the major axis of wetland A. The clayey peat deposit was the most thick at the center of wetland A that horizontal distance is 100 m. As the depth below ground surface of clayey peat deposit is less than 27 cm in the wetland B, we can infer that the life for the wetland B is being finished. Sediment composition of wetland C is simple because wetland C is small scale, and clayey peat deposit is distributed at 10~34 cm depth below ground surface. Sediment sampled by borehole survey in the Dalpo wetland was cut at interval of 10 cm, then organic content was analyzed. Organic content of wetland A sediment showed more than 40% until 70 cm depth below ground surface, also sediment of wetland B is similar to wetland A until 10 cm depth below ground surface, but is showed within 20 % above 30 cm depth below ground surface. Organic content of wetland B is showed the lowest as organic content near the ground surface is about 40%. All of the three wetlands, organic content is showed higher at clayey peat deposit near to ground surface. This is caused by finer particles of the clayey peat deposit, also organic materials were supplied from dead vegetation. Organic content of the Dalpo wetland showed in order of wetland A > wetland C > wetland B. This result is caused by thickness of clayey peat deposit in sediment. Through this study, it was verified that organic content of the Dalpo wetland sediment was dominated by particle size of sediment and vegetation of the upper part.

• Journal of Adhesion and Interface
• /
• v.4 no.1
• /
• pp.35-42
• /
• 2003

Polystyrene nanocapsules containing octadecane as a core material were prepared by miniemulsion polymerization. The morphology and size of the nanocapsules were measured with varying the surfactant concentration, content of initiator, core/shell ratio and content of comonomer. The morphologies of the prepared nanoparticles were examined by a scanning electron microscope, a transmission electron microscope and the core material was confirmed by a differential scanning calorimeter. The particles below 70 nm in diameter were formed at a high surfactant concentration. The size of the nanoparticles was not significantly affected by the initiator content. With increasing the core/shell ratio and polar comonomer content, the particle size and its distribution were increased.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.16 no.12
• /
• pp.1126-1133
• /
• 2004

This paper presents an experimental measurement of effective thermal conductivity in an adsorbent packed bed with silica gel A type. The effective thermal conductivity was measured under different conditions of the adsorbent bed temperature, pressure, particle size and water content by using the transient hot wire method. The measured effective thermal conductivity showed to become bigger with decreasing particle size or increasing water content, but it was a little affected with increasing bed temperature and pressure. The bed temperature was varied in the range of 1$0^{\circ}C$ (equation omitted) T (equation omitted) 5$0^{\circ}C$ and the pressure in the range of 10 kPa (equation omitted) P (equation omitted) 190 kPa. The results show that 0.10～0.18 W/mㆍK of effective thermal conductivity measured for the zero water content.

• Food Science and Preservation
• /
• v.17 no.4
• /
• pp.513-518
• /
• 2010

This study was carried out to estimate the moisture sorption characteristics and prediction model of anchovy powders with different particle size as above 80 mesh, 80-60 mesh and 40-60 mesh. The equilibrium moisture content had higher values at lower storage temperatures, and higher water activity. The monolayer moisture content calculated using the GAB equation showed a higher level of significance than that of BET equation. The estimated monolayer moisture content was 0.024-0.052 g $H_2O/g$ dry solid. The absorption enthalpy was calculated with different particle size and various water activities. It showed that the absorption energy was decreased with increasing water activity but no difference was found on particle size increasement. The fitness of the isotherm curve was shown to be in the order of Khun, Halsey, Caurie and Oswin model. The prediction model equations for the moisture content were established by ln(time), water activity, and temperature, respectively. The model equation will be helpful for future work on drying and storage of anchovy powder.

• Journal of Korean Society for Atmospheric Environment
• /
• v.26 no.1
• /
• pp.94-102
• /
• 2010

Water content of $PM_{2.5}$ (particles in the atmosphere with a diameter of less than or equal to a nominal $2.5{\mu}m$) was estimated by using a gas/aerosol equilibrium model, SCAPE2, for the particles collected at Seoul and Gosan, Korea. From measured and analyzed characteristics of the particles, the largest difference between Seoul and Gosan is the proportions of total ammonia (t-$NH_3$=gas phase $NH_3$+particle phase ${NH_4}^+$), total nitric acid (t-$HNO_3$=gas phase $HNO_3$+particle phase ${NO_3}^-$) and sulfuric acid ($H_2SO_4$). Even though both sites have sufficient t-$NH_3$ to neutralize acidic species such as $H_2SO_4$, t-$HNO_3$, and t-HCl (total chloric acid=gas phase HCl+particle phase $Cl^-$), equivalent fraction of t-$NH_3$ and t-$HNO_3$ are higher at Seoul and $H_2SO_4$ is higher at Gosan. Based on the modeling result, it is identified that the $PM_{2.5}$ at Seoul is more hygroscopic than Gosan if the meteorological conditions are the same. To reduce water content of $PM_{2.5}$, and thus, mass concentration, control measures for ammonia and nitrate reduction are needed for Seoul, and inter-governmental cooperation is required for Gosan.

• Polymer(Korea)
• /
• v.35 no.5
• /
• pp.451-457
• /
• 2011

The effect of latex particle size on rheological and electrical properties of latex-blended polystyrene (PS)/multi-walled carbon nanotube (MWCNT) nanocomposites was investigated. Mono-dispersed PS particles synthesized either by emulsifier-free emulsion polymerization or by dispersion polymerization were mixed with MWCNTs under ultrasonication, and freeze-dried to prepare the nanocomposites. As the MWCNT content increased, storage modulus, complex viscosity and electrical conductivity were substantially increased. The increase of storage modulus and complex viscosity was higher for larger PS particles. The effect of particle size on electrical properties was different depending on MWCNT content. With lower MWCNT content, the nanocomposite prepared by smaller PS particles showed higher electrical conductivity, but the opposite result was given as the content increased.

• Journal of Korean Society of Water and Wastewater
• /
• v.24 no.5
• /
• pp.609-615
• /
• 2010

This study examined the change of water content in sludge using direct current electric equipment for decreasing the amount of sludge. The experiment showed that the average density of solids in the sludge treated by direct current before the centrifugal dewatering process was increased by 47.8%, when compared to those not treated by direct current. From the result of measuring the granularity of the sludge by the direct current treatment, that the average particle size of the sludge that was not exposed to the electric current was 52.36 ${\mu}m$, and more than 90% of the sludge was <94.29 ${\mu}m$ in size. On the other hand, the average particle size of the sludge passed through the direct current was 28.67 ${\mu}m$, and more than 90% of the sludge was 52.46 ${\mu}m$. This means that the average particle size of the sludge treated by the direct current was 45.2% smaller, and the standard deviation of granularity was improved. Because of water that separated from sludge moves to the (+) pole, larger particles become smaller and fine particles combine together, resulting in the equalization of the particle size. On the sludge after the centrifugal dehydrator, the change of the water content by the direct current was measured. The results showed that the average density of the solids was increased by 44.2% compared.

• Applied Chemistry for Engineering
• /
• v.9 no.5
• /
• pp.758-762
• /
• 1998

In preparing void latex particles by emulsion polymerization, the weight mean particle size of which is ranged $0.3{\mu}m{\sim}1.5{\mu}m$, reaction parameters were investigated in order to elucidate their effects on the size distribution and the solid content of emulsion polymer. Experimental results showed that the weight mean particle size of hydrophillic core polymer was reduced as the concentration of sodium dodecylbenzene sulfonate (SDS) increased. The size of void polymethyl-methacrylate-polystyrene composite latex particles became larger as the concentration of styrene monomer and the sodium persulfate increased. However, the size of void latex particles was reduced as the feeding rate of acrylic acid increased. The solid content of emulsion polymer was strongly dependent on the addition of stylene monomer. By increasing the concentration of styrene monomer the solid content of emulsion polymer increased linearly.

• Journal of the Korean Society of Combustion
• /
• v.13 no.2
• /
• pp.23-32
• /
• 2008

Gasification characteristics in the fluidized bed reactor are essential for the design of a gasification furnace to optimize the operation condition. Moisture content of the solid fuel is one of the important factors to influence directly the gasification characteristics. So it is necessary to investigate the effect of moisture content of solid fuel in partial oxidation condition. Gasification characteristics are investigated with results from thermogravimetric analyzer and lab-scale fluidized bed reactor for wood and RDF samples along with changing moisture contents. Additionally lab-scale fluidized bed reactor was run continuously and gas concentrations at the exit were measured. It is observed that the rate of reaction in partial oxidation condition is between the results from the combustion environment and from the inert condition. Moisture content in a particle slows down the heating rate of a particle. So, reaction is delayed by the moisture content. However, RDF samples those are easy to break-up don't show the effect of moisture content. The result of continuous operation condition shows that proper moisture content promotes gasification because steam from the particles helps gasification of the solid fuel. A simulation to predict the syn-gas composition was conducted by the Aspen Plus process simulator. The cold gas efficiency of the experiment was compared with results from the simulation.