• Korean Journal of Materials Research
• /
• v.15 no.11
• /
• pp.697-704
• /
• 2005

The deformation behavior of a bulk amorphous and crystallized amorphous $Zr_{22.5}Ti_{14}Cu_{12.5}Ni_{10}Be_{22.5}$ alloy extracted from a commercial golf club head was characterized at room temperature ana $300^{\circ}C$. At room temperature, amorphous specimens revealed higher yield stress and ductility than partially crystallized alloy specimens. Amorphous alloy displayed some plasticity before fracture, which resulted from strain hardening and repeated crack initiation and propagation. The fracture is mainly localized on one major shear band, and the compressive fracture angle of the amorphous specimen between the stress axis and the fracture plane was about $40^{\circ}$ Scanning electron microscope observations revealed mainly a vein-like structure in the amorphous alloy But the fracture surface of partially crystallized amorphous alloy consisted of vein-like and featureless fracture structure. The partially crystallized alloy extracted from the thick part of the club fractured in the elastic region, at a much lower stress level than the amorphous, suggesting that relatively coarse crystal particles formed during cooling cause the brittle fracture.

• Journal of Powder Materials
• /
• v.14 no.1 s.60
• /
• pp.50-55
• /
• 2007

The hydrogen sorption speeds of $Zr_{57}V_{36}Ti_7$ amorphous alloy and its crystallized alloys were evaluated at room temperature. $Zr_{57}V_{36}Ti_7$ amorphous alloy was prepared by ball milling. The hydrogen sorption rate of the partially crystallized alloy was higher than that of amorphous. The enhanced sorption rate of partially crystallized alloy was explained in terms of grain refinement that has been known to promote the diffusion into metallic bulk of the gases. The grain refinement could be obtained by crystallization of amorphous phase resulting in the observed increase in sorption property.

• Korean Journal of Materials Research
• /
• v.15 no.12
• /
• pp.802-808
• /
• 2005

The hydrogen sorption speeds of $Zr_{57}V_{36}Fe_7$ amorphous alloy and its crystallized alloys were evaluated at room temperature $Zr_{57}V_{36}Fe_7$ amorphous alloy was prepared by ball milling. The amorphous alloy was crystallized through two stages. Initially, $\alpha-Zr$ solid solution was appeared from the amorphous phase. Two cubic Laves compounds were precipitated afterwards from the remained amorphous and from excessively saturated solid solution at higher temperature. The hydrogen sorption speed of the partially crystallized alloy was higher than that of amorphous. The enhanced sorption speed of partially crystallized alloy was explained in terms of surface oxygen stability which has been known to retard the activation of amorphous alloys. The retardation could be reduce by crystallization process resulting in the observed increase in sorption property.

• Journal of Welding and Joining
• /
• v.25 no.3
• /
• pp.28-36
• /
• 2007

A bulk amorphous NiTiZrSiSn powder produced using an inert gas atomization was sprayed by kinetic spraying process that is basically a solid-state deposition process onto a mild steel substrate. They were successfully overlaid onto the mild steel substrate. In order to evaluate the tribological behavior of the kinetic sprayed NiTiZrSiSn BMG (Bulk Metallic Glass) coatings, a partially crystallized coating and a fully crystallized coating were prepared by the isothermal heat treatments. Tribological behaviors were investigated in view of friction coefficient, hardness and amorphous phase fraction of coating layer. Surface morphologies and depth in the wear tracks were observed and measured by scanning electron microscope and alpha-step. From the examination of the scratch wear track microstructure, transition from the ductile like deformation (micro cutting) to the brittle deformation (micro fracturing) in the scratch groove was observed with the increase of the crystallinity.

• Journal of the Korean Ceramic Society
• /
• v.28 no.11
• /
• pp.892-896
• /
• 1991

The cyrstallization behavior of lead titanate powders prepared by sol-gel and coprecipitation techniques was investigated. The lead titanate precursors were derived from a mixed solution of lead nitrate and titanium tetrachloride at 4$0^{\circ}C$ to 43$^{\circ}C$ and pH of 9.00 to 9.75. The X-ray diffraction patterns of the dried gel and coprecipitated powders showed it to be amorphous. DTA runs of the powders indicated crystallization to occur at 475~48$0^{\circ}C$. However, the amorphous powders were partially crystallized at 400~45$0^{\circ}C$ with sufficient annealing time. The room temperature Raman spectra from heat-treated powders changed continuously from amorphous to crystalline state with increasing heat-treating temperature. By annealing coprecipitated powders, a dramatic change in the Raman spectra due to the structural relaxation as the annealing temperatures increased, was clearly visible. i.e., coprecipitated, gel, and crystalline structure, in turn.

• Journal of the Korean Ceramic Society
• /
• v.52 no.2
• /
• pp.108-113
• /
• 2015

In an effort to evaluate the practicability of an imprinting technique for amorphous chalcogenide film in Ge-based compositions, we investigate the deformation behavior of the surface of amorphous $GeSe_2$ film deposited via a thermal evaporation route according to varying static loads applied at elevated temperatures. We observe that, under these static loading conditions, crystallization tends to occur on its surface relatively more easily than in As-based $As_2Se_3$ films. As for the present $GeSe_2$ film, higher processing temperatures are required in order to make its surface reflect the given stamp patterns well; however, in this case, its surface becomes partially crystallized in the monoclinic $GeSe_2$ phase. The increased vulnerability of this amorphous $GeSe_2$ film toward surface crystallization under static loading, when compared with the $As_2Se_3$ counterpart, is explained in terms of the topological aspects of its amorphous structure.

• Journal of Powder Materials
• /
• v.3 no.3
• /
• pp.174-180
• /
• 1996

Microstructure and phase transformation of mechanically alloyed TiNi powders added to aluminium matrix for enhancing the damping properties were studied. Four compositions between 48.5 and 51.5 at% Ti intermetallic compounds were selected to control the fraction of martensite phase. Mechanically alloyed TiNi powders were heat-treated at vacuum of $10^{-6}$ torr for crystallization. Ball milled AI/TiNi composite powders were swaged at room temperature and rolled at 450 $^{\circ}C$. After mechanical alloying for 10 hours, Ti and Ni elements were alloyed completely and amorphous phase was formed. Amorphous phase was crystallized to martensite (Bl9') and austenite(B2) after heat treating for 1 hour at the temperature of 850 $^{\circ}C$, and TiNi$_3$, intermetallic compound was partially formed. Considerable amount of martensite phase was remained after swaging and rolling.

• Journal of the Korean Ceramic Society
• /
• v.27 no.4
• /
• pp.521-528
• /
• 1990

Li2O.2SiO2 glass-ceramics were made from the melt by the nucleation and growth treatment. The optimum nucleation temperature and time were determined from DTA curves of as-quenched and thermally treated glasses, and found to be 44$0^{\circ}C$ and 3hrs. The optical microscopic technique was also used to support this result. The volume fractions of crystals present in the partially crystallized specimens were measured using the optical microscopy and the amorphous X-ray scattering methods. The degree of crystallization increased with increasing the crystallization temperature and time. The crystalline phase identified by X-ray diffraction was lithium disilicate. As the crystallinity increased up to 95%, the transmittance of glass-ceramics was decreased linearly. It was also found that for the same heat treatment condition (575$^{\circ}C$, 30min), a thicker specimen showed higher transmittance, presumably due to less crystallinity.

• Advances in materials Research
• /
• v.1 no.1
• /
• pp.31-35
• /
• 2012

Unique tooth-like (milky white) color ${\beta}$-Ti dental arch wires are prepared by anodization in a 1M $H_2SO_4$ electrolyte at $30^{\circ}C$ and 30 V for 88 min and 40 s. Aggregates are formed on these surfaces of the anodized wires with tooth-like colors, and the results are different from those of the anodized wires with monochromatic colors which have smooth oxide surfaces. Similar to the monochromatic wires, the composition of the oxide layer is $TiO_{2-x}$ and the x approaches zero at the outer layer. But different from the amorphous structure observed in monochromatic wires, the oxide layers are partially crystallized with an anatase structure. The milky white colors result from the rough and crystalized oxide layers, not by the interference effect as observed in monochromatic wires.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.03a
• /
• pp.21-21
• /
• 2010

(Ba,Sr)$TiO_3$ (BST) thin film with a perovskite structure has potential for the practical application in various functional devices such as nonvolatile-memory components, capacitor, gate insulator of thin-film transistors, and electro-optic devices for display. Normally, the BST thin films derived from sol-gel and sputtering are amorphous or partially crystalline when processed below $600^{\circ}C$. For the purpose of integrating BST thin film directly into a Si-based read-out integrated circuit (ROIC), it is necessary to process the BST film below $400^{\circ}C$. The microstructural and electrical properties of low-temperature crystallized BST film were studied. The BST thin films have been fabricated at $350^{\circ}C$ by UV-assisted rapidly thermal annealing (RTA). The BST films are in a single perovskite phase and have well-defined electrical properties such as high dielectric constant, low dielectric loss, low leakage current density, and high breakdown voltage. Photoexcitation of the organics contained in the sol-gel-derived films by high-intensity UV irradiation facilitates elimination of the organics and formation of the single-crystalline phase films at low temperatures. The amorphous BST thin film was transformed to a highly (h00)-oriented perovskite structure by high oxygen pressure processing (HOPP) at as low as $350^{\circ}C$. The dielectric properties of BST film were comparable to (or even better than) those of the conventionally processed BST films prepared by sputtering or post-annealing at temperature above $600^{\circ}C$. When external pressure was applied to the well-known contractive BST system during annealing, the nucleation energy barrier was reduced; correspondingly, the crystallization temperature decreased. The UV-assisted RTA and HOPP, as compatible with existing MOS technology, let the BST films be integrated into radio-frequency circuit and mixed-signal integrated circuit below the critical temperature of $400^{\circ}C$.