• Journal of the Korean Geotechnical Society
• /
• v.23 no.11
• /
• pp.87-98
• /
• 2007

For the quick rehabilitation of a fire-damaged tunnel structure, it is the most important procedure to investigate the fire-induced damaged zone rapidly. This study aims to propose a new drilling resistance testing method by which mechanical properties of tunnel concrete lining altered by high temperature can be estimated easily and continuously. Especially, it alms to derive the relationships to estimate mechanical properties of mortar and concrete materials from drilling parameters. To obtain the optimum testing condition, a series of drilling resistance tests were carried out for mortar specimens. When the rotation per minute of drill bit, tile penetration rate and the bit diameter were 1,300 rpm, 1.40 mm/sec, and 10 mm respectively, the deviation of measured drilling resistance forces was minimal. Under the optimum testing condition, the relationships between drilling resistance and mechanical properties of mortar specimens were shown to be very favorable. The concept of replacing a mean value of resistance farces measured during drilling with the resistance energy was proposed to consider the effects of randomly distributed aggregates inside a concrete material on drilling resistance. When the concept was applied to concrete materials, a favorable relationship between actual compressive strength and drilling resistance energy was also successfully derived.

• The Journal of Engineering Geology
• /
• v.32 no.1
• /
• pp.59-72
• /
• 2022

This study employed a 3-D numerical analysis based on the distinct element method to estimate the strength and deformability of a Cretaceous biotite granitic rock mass at Gijang, Busan, Korea. A workflow was proposed to evaluate the scale effect and the representative elementary volume (REV) of mechanical properties for fractured rock masses. Directional strength and deformability parameters such as block strength, deformation modulus, shear modulus, and bulk modulus were estimated for a discrete fracture network (DFN) in a cubic block the size of the REV. The size of the mechanical REV for fractured rock masses in the study area was determined to be a 15 m cube. The mean block strength and mean deformation modulus of the DFN cube block were found to be 52.8% and 57.7% of the intact rock's strength and Young's modulus, respectively. A constitutive model was derived for the study area that describes the linear-elastic and orthotropic mechanical behavior of the rock mass. The model is expected to help evaluate the stability of tunnels and underground spaces through equivalent continuum analysis.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.5C
• /
• pp.293-301
• /
• 2008

Soil profiling is one of the most important work among geotehnical engineering practice. Generally, soil profile is estimated from the observation of soil samples during subsurface exploration but such estimation also includes some experiencing aspects such as flushed water from the borehole, slime colour, boring speed and so on. In addition, since the capacity of hydraulic drill rig is significantly increased, thin layers might be easily missed. So, continuous soil profile is almost impossible over all depth to be bored from conventional subsurface exploration. While CPT or CPTu can serve continuous soil profile information over all depth generally in 5cm interval. Many charts or methods for soil profile from CPT result have been proposed during last several decades over the world. However they have not been verified in local ground condition in Korea. In this research, CPT results and soil classification results based on USCS were compiled from 17 sites over the Korea. Soil classification results by using 7 CPT soil classification charts were compared with those of USCS for the compiled database. Most proper CPT soil classification chart for Korean soil characteristics was evaluated and effective parameters for the soil classification from CPT were discussed. Finally interrelationship between CPT soil classification chart and USCS soil classification was evaluated.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.4B
• /
• pp.363-374
• /
• 2008

Intensity-Duration-Frequency (IDF) curve that is essential to calculate rainfall quantiles for designing hydraulic structures in Korea is generally formulated by regression analysis. In this study, IDF curve derived by the cumulative distribution function ("IDF by CDF") of the proper probability distribution function (PDF) of each site is suggested, and the corresponding parameters of IDF curve are computed using genetic algorithm (GA). For this purpose, IDF by CDF and the conventional IDF derived by regression analysis ("IDF by REG") were computed for 22 Korea Meteorological Administration (KMA) rainfall recording sites. Comparisons of RMSE (root mean squared error) and RRMSE (Relative RMSE) of rainfall intensities computed from IDF by CDF and IDF by REG show that IDF by CDF is more accurate than IDF by REG. In order to accommodate the effect of the recent intensive rainfall of Korea, the rainfall intensities computed by the two IDF curves are compared with that by at-site frequency analysis using the rainfall data recorded by 2006, and the result from IDF by CDF show the better performance than that from IDF by REG. As a result, it can be said that the suggested IDF by CDF curve would be the more efficient IDF curve than that computed by regression analysis and could be applied for Korean rainfall data.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.2B
• /
• pp.225-236
• /
• 2008

The techniques to calculate the probability precipitation for the design of hydrological projects can be determined by the point frequency analysis and the regional frequency analysis. Probability precipitation usually calculated by point frequency analysis using rainfall data that is observed in rainfall observatory which is situated in the basin. Therefore, Probability precipitation through point frequency analysis need observed rainfall data for enough periods. But, lacking precipitation data can be calculated to wrong parameters. Consequently, the regional frequency analysis can supplement the lacking precipitation data. Therefore, the regional frequency analysis has weaknesses compared to point frequency analysis because of suppositions about probability distributions. In this paper, rainfall observatory in Korea did grouping by cluster analysis using position of timely precipitation observatory and characteristic time rainfall. Discordancy and heterogeneity measures verified the grouping precipitation observatory by the cluster analysis. So, there divided rainfall observatory in Korea to 6 areas, and the regional frequency analysis applies index-flood techniques and L-moment techniques. Also, the probability precipitation was calculated by the regional frequency analysis using variable kernel density function. At the results, the regional frequency analysis of the variable kernel function can utilize for decision difficulty of suitable probability distribution in other methods.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.1C
• /
• pp.43-52
• /
• 2006

Despite several constitutive models have been proposed and applied, it is still difficult to choose a suitable model and to estimate adequate analysis parameters. Furthermore, a cyclic shear behavior under the volume change caused by the seepage is more complex. None of the constitutive model is available at present in the expression of the cyclic behavior of soil under an additional volume change condition by seepage. Therefore, a new geotechnical hybrid simulation system which can control the pore water immigration was developed. The system enables a quantitative evaluation of the residual deformation such as lateral spreading and settlement caused by the liquefaction. The seismic responses in a one-dimensional slightly inclined multilayered soil system are taken into consideration, and the soils are governed by both equation of motion and the continuity equation. Furthermore, the estimation and the selection of the soil parameter for the representation of the strong nonlinearity of the material are not required, because soil behaviors under the earthquake motions are directly introduced instead of a numerical soil constitutive model. This paper presents the concept and specifications of the system. By applying the system to an example problem, the permeability effect on the seismic response during cyclic shear is studied. The importance of the volume change characteristics of sandy soil during and after cyclic shear is shown in conclusion.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.1C
• /
• pp.65-76
• /
• 2010

Recent earthquake events revealed that severe seismic damages were concentrated mostly at sites composed of soil sediments rather than firm rock. This indicates that the site effects inducing the amplification of earthquake ground motion are associated mainly with the spatial distribution and dynamic properties of the soils overlying bedrock. In this study, an integrated GIS-based information system for geotechnical data was constructed to establish a regional counterplan against ground motions at a representative metropolitan area, Seoul, in Korea. To implement the GIS-based geotechnical information system for the Seoul area, existing geotechnical investigation data were collected in and around the study area and additionally a walkover site survey was carried out to acquire surface geo-knowledge data. For practical application of the geotechnical information system used to estimate the site effects at the area of interest, seismic zoning maps of geotechnical earthquake engineering parameters, such as the depth to bedrock and the site period, were created and presented as regional synthetic strategy for earthquake-induced hazards prediction. In addition, seismic zonation of site classification was also performed to determine the site amplification coefficients for seismic design at any site and administrative sub-unit in the Seoul area. Based on the case study on seismic zonations for Seoul, it was verified that the GIS-based geotechnical information system was very useful for the regional prediction of seismic hazards and also the decision support for seismic hazard mitigation particularly at the metropolitan area.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.29 no.4
• /
• pp.380-388
• /
• 2023

This study estimates the metacentric height (GM) of a model ship by varying the transverse weight distribution, considering the effects of the roll period and moment of inertia, and compares it with the GM values measured by the inclining test. In the process, the relationship between the values is analyzed. Three types of ships-a 7-ton fishing vessel, 20-ton fishing vessel, and KRISO Very Large Crude-oil Carrier (KVLCC)-were used for the experiment and comparison. The roll period and moment of inertia were measured using the free roll decay and swing frame tests, and the GM was measured using inclining test. The estimated GM from the roll period and moment of inertia showed the same trend as the GM measured using the inclining test in the change of the weight distribution. However, the GM values measured using the inclining test were lower. Therefore, additional correction factors or parameters other than the roll period and moment of inertia are necessary for estimating GM. In the future, the relationship between the weight center and the estimated GM will be analyzed to derive the correction factors.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.29 no.7
• /
• pp.863-870
• /
• 2023

Ship capsize accidents are common in coastal waters, particularly involving small fishing boats. To prevent there overturing accidents in small fishing boats, their stabilities must be assessed at the initial design step. However, the available information during the initial design step is limited, posing challenges in performing a reliable stability evaluation. Therefore, this study presents a plan to estimate the transverse metacenter (GM) of small fishing boats using parameters such as KM, KG, and TRIM that can be determined at the initial design step. Stability was evaluated by comparing GM with the minimum transverse metacenter (GMmin) specified in the standard safety evaluation criteria for fishing boats. To calculate the required trim value for hydrostatic characteristics using K-SHIP, a stability assessment program provided by the Korea Maritime Safety and Transportation Corporation, the initial trim state is estimated based on the ship lines using the commercial CFD program STAR-CCM+. GM is then calculated by assessing the hydrostatic characteristics in relation to the boat lines using K-SHIP. Furthermore, the stability of the fully loaded state is compared by subtrcating GM from GMmin. One constructed ship is designated as the standard ship, and the stability assessment method proposed in this study is applied to evaluate stability and validate its effectiveness. Consequently, the representative line of a 4.99-ton fishing boat and nine modular lines models derived from it were evaluated, ultimately identifying a relatively superior stability.

• Journal of Environmental Health Sciences
• /
• v.49 no.6
• /
• pp.312-323
• /
• 2023

Background: Environmental concentrations of substances can be estimated by K-CHESAR based on main, industrial, and use categories (MC/IC/UC) and ECETOC TRA based on environmental or specific environmental categories (ERC or spERC). Objectives: Three different systems for estimating environmental concentrations were compared to figure out their order with possible reasons along with relationship of regional predicted environmental concentrations (PEC_regional) and final PEC_local for various uses of a substance. Methods: Typical uses of the case substance and their corresponding ERCs were selected from the webpage of the European Chemical Agency. Proper MC/IC/UC and spERC were assigned to each ERC. Emission fractions were compared for each assessment code from the available database. PECs were calculated by three estimating systems: K-CHESAR using MC/IC/UC, ECETOC TRA using ERC, and ECETOC TRA using spERC with their default values for input parameters. Percentage of PEC_regional to PEC_local were manually calculated for each use. Results: Emission factors decreased in the order of ERC > MC/IC/UC > spERC. Values of the final PEC_local derived as sum of PEC_regional and Clocal decreased in the order of calculations using ECETOC TRA-ERC>KCHESAR with MC/IC/UC>ECETOC TRA-spERC for all environmental media. Percentages of PEC_{regional,water} to PEC_local,water ranged from 0 to 10.3% in industrial uses calculated with MC/IC/UC and ERC but 96.3 to 100% in wide dispersive uses of ERC and spERC where values of C_local,water are estimated to be very low. Conclusions: ECETOC TRA generated the most refined PNEC values with spERC and the least with ERC, while K-CHESAR with MC/IC/UC generated values between the two results. The ratio of PEC_regional to PEC_local can be a good measure for performing suitable estimation of PNECs according to use.