• Journal of Biomedical Engineering Research
• /
• v.18 no.1
• /
• pp.25-36
• /
• 1997

To regulate cardiac output of the Total Artificial Heart(TAH) physiologically, the hemodynamic information must be toed back to the controller. So far, our group has developed an automatic cardiac output control algorithm using the motor current waveform, It is, however difficult to detect the preload level such as a filling status of ventricular inflow and the variation of atrial pressures within normal physiologic range(0-15 mmHg) by analyzing the motor current which simultaneously reflects the afterload effect. On the other hin4 the interventricular volume pressure(IVP) which is not influenced by arterload but by preload is a good information source for the estimation of preload states. In order to find the relationship between preload and IVP waveform, we set up the artificial heart system on the Donovan type mock circulatory system and measured the IVP waveform, right and left atrial pressures, inflow and outflow waveforms and the signals represented the information of moving actuator's position. We shows the feasibility of estimating the hemodynamic changes of inflow by using IVP waveform. fife found that the negative peak value of IVP waveform is linearly related to atrial pressures. And we also found that we could use the time to reach the negative peak in IVP waveform, the time to open outflow valve, the area enclosed IVP waveform as unfu parameters to estimate blood filling volume of diastole ventricle. The suggested method has advantages of avoiding thrombogenesis, bacterial niche formation and increasing longterm reliability of sensor by avoiding direct contact to blood.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.25 no.5
• /
• pp.425-430
• /
• 2015

This paper is a study to improve the classification efficiency of rotating objects by using deep neural networks to which a deep learning algorithm was applied. For the classification experiment of rotating objects, COIL-20 is used as data and total 3 types of classifiers are compared and analyzed. 3 types of classifiers used in the study include PCA classifier to derive a feature value while reducing the dimension of data by using Principal Component Analysis and classify by using euclidean distance, MLP classifier of the way of reducing the error energy by using error back-propagation algorithm and finally, deep learning applied DBN classifier of the way of increasing the probability of observing learning data through pre-training and reducing the error energy through fine-tuning. In order to identify the structure-specific error rate of the deep neural networks, the experiment is carried out while changing the number of hidden layers and number of hidden neurons. The classifier using DBN showed the lowest error rate. Its structure of deep neural networks with 2 hidden layers showed a high recognition rate by moving parameters to a location helpful for recognition.

• Journal of electromagnetic engineering and science
• /
• v.18 no.2
• /
• pp.117-128
• /
• 2018

In this paper, compact linear dual polarized series-fed $1{\times}2$ linear and $2{\times}2$ planar arrays antennas for airborne SAR applications are proposed. The proposed antenna design consists of a square radiating patch that is placed on top of the substrate, a quarter wave transformer and $50-{\Omega}$ matched transformer. Matching between a radiating patch and the $50-{\Omega}$ microstrip line is accomplished through a direct coupled-feed technique with the help of an impedance inverter (${\lambda}/4$ impedance transformer) placed at both horizontal and vertical planes, in the case of the $2{\times}2$ planar array. The overall size for the prototype-1 and prototype-2 fabricated antennas are $1.9305{\times}0.9652{\times}0.05106{{\lambda}_0}^3$ and $1.9305{\times}1.9305{\times}0.05106{{\lambda}_0}^3$, respectively. The fabricated structure has been tested, and the experimental results are similar to the simulated ones. The CST MWS simulated and vector network analyzer measured reflection coefficient ($S_{11}$) results were compared, and they indicate that the proposed antenna prototype-1 yields the impedance bandwidth >140 MHz (9.56-9.72 GHz) defined by $S_{11}$<-10 dB with 1.43%, and $S_{21}$<-25 dB in the case of prototype-2 (9.58-9.74 GHz, $S_{11}$< -10 dB) >140 MHz for all the individual ports. The surface currents and the E- and H-field distributions were studied for a better understanding of the polarization mechanism. The measured results of the proposed dual polarized antenna were in accordance with the simulated analysis and showed good performance of the S-parameters and radiation patterns (co-pol and cross-pol), gain, efficiency, front-to-back ratio, half-power beam width) at the resonant frequency. With these features and its compact size, the proposed antenna will be suitable for X-band airborne synthetic aperture radar applications.

• Proceedings of the Korean Magnetic Resonance Society Conference
• /
• 2002.08a
• /
• pp.80-80
• /
• 2002

MnPSO-34 and Mn-impregnated SAPO-34 (Mn-SAPO-34) sample were prepared with various manganese contents and studied by electron spin resonance (ESR) and electron spin-echo modulation (ESEM). Electron spin-echo modulation analysis of 0.07mol ％ Mn(relative to p) in MnAPSO-34 with adsorbed D$_2$O shows two deuteriums at 0.25 nm and two at 0.36 nm from Mn. This suggests that two waters hydrate an MnO4 configuration with a D-O bond orientation for the waters as expect for a negatively charged site at low manganese content (0.07 mol％), the ESR spectra of MnAPSO-34 and MnH-SAPO-34 exhibit the same parameters (g 2.02 and A 87 G), but the spectra obtained from MnAPSO-34 samples are better resolved. TGA of as-synthesized MnAPSO-34 shows that the decomposition temperature in the range 200-$600^{\circ}C$ of the morpholine is 12$^{\circ}C$ higher than that in as-synthesized MnH-SAPO-34. Infrared spectra shows that the position of a band at about 15 cm-1 toward higher energy in MnAPSO-34 versus MnH-SAPO-34. The modulation depth of the two-pulse ESE of MnAPSO-34 with absorbed D$_2$O is deeper than that of MnH-SAPO-34 with absorbed D$_2$O. Three-pulse ESEM of MnAPSO-34 and MnH-SAPO-34 with absorbed deuterium oxide shows that the local environments of manganese in the hydrated samples are different, suggesting that Mn(II) is framework substituted in MnAPSO-34 since it obviously occupies an extra-framework position in MnH-SAPO-34

• Journal of Power System Engineering
• /
• v.21 no.4
• /
• pp.62-69
• /
• 2017

Because the moist foods like anchovy were appeared lower quality by hot air that occurred the lipid oxidation, the drying system by using the cold air has been used widely. This study has been carried out on the performance improvement according to arrangement angle of baffle and location of air duct in the cold air dryer. The main parameters in this study are the arrangement angles which are without, $0^{\circ}$, $10^{\circ}$, $20^{\circ}$, $30^{\circ}$ and $40^{\circ}$, and the locations of air duct are without, front, center and back. For this study we have conducted the numerical analysis method using fluent in order to obtain the optimal condition of the drying performance. As the arrangement angle of baffle is increased, the relative humidity is proportionally decreased, the value at $40^{\circ}$ is 42.2% that indicate the reduction of about 4% than without it. After the air duct was installed, the decreased relative humidity is showed within 1%, therefore, the effect of air duct for improving the dry capacity is more large than the arrangement angle of baffle. Finally, we have obtained the optimal conditions that the arrangement angle is $40^{\circ}$ with the air duct for a cold air dryer.

• Journal of Korea Multimedia Society
• /
• v.11 no.4
• /
• pp.516-524
• /
• 2008

This paper presents a new modeling technique for the simulation of cloth specific characteristics with a set of hard constraints using an implicit constraint enforcement scheme. A conventional explicit Baumgarte constraint stabilization method has several defects. It requires users to pick problem-dependent coefficients to achieve fast convergence and has inherent stabilization limits. The proposed implicit constraint enforcement method is stable with large time steps, does not require problem dependent feed-back parameters, and guarantees the natural physics-based motion of an object. In addition, its computational complexity is the same as the explicit Baumgarte method. This paper describes a formulation of implicit constraint enforcement and provides a constraint error analysis. The modeling technique for complex components of cloth such as seams, buttons, sharp creases, wrinkles, and prevention of excessive elongation are explained. Combined with an adaptive constraint activation scheme, the results using the proposed method show the substantial enhancement of the realism of cloth simulations with a corresponding savings in computational cost.

• Journal of Korean Neurosurgical Society
• /
• v.29 no.3
• /
• pp.372-378
• /
• 2000

The carpal tunnel syndrome is one of the most common entrapment neuropathy. Surgical treatments consist of conventional open technique, alternative technique using retinaculatome, and endoscopic surgery. This study compares the outcomes of surgical treatment of carpal tunnel syndrome following conventional versus endoscopic release. The authors reviewed 56 cases of 33 patients with carpal tunnel syndrome treated surgically in our institute from January 1991 to May 1998. The follow-up evaluation was possible in 36 cases of 20 patients who had conventional release and in 11 cases of 7 patients with endoscopic release. The following parameters were evaluated for comparison : improvement of symptom, return to normal work, recovery of strength of grip and pinch, rate of complication, follow-up electrophysiologic finding. Compared with open decompression, the group of endoscopic decompression needed significantly less time to go back to work(p<0.001). Also strength of grip and pinch improved faster in the group of endoscopic decompression as well, compared with open decompression(p<0.05). These results indicate that endoscopic procedure is an excellent, minimally invasive method to treat carpal tunnel syndrome, performed by surgeons who are fully aware of the anatomy.

• Steel and Composite Structures
• /
• v.25 no.6
• /
• pp.671-684
• /
• 2017

Elastic-plastic shear buckling behaviors of the web-post in a Castellated Steel Beam (CSB) with hexagonal web openings under vertical shear force were investigated further using Finite Element Model (FEM) based on a sub-model, which took the upper part of the web-post under horizontal shear force to represent the whole web-post under vertical shear force. A simplified design method for the web-post elastic-plastic shear buckling strength was proposed based on simulation results of the sub-model. Proper boundary conditions were applied to the sub-model to assure that its behaviors were identical to those of the whole web-post. The equation to calculate the thin plate elastic shear buckling strength was adopted as the basic form to build the design equation for elastic-plastic buckling strength of the sub-model. Parameters that might affect the elastic-plastic shear buckling strength of the whole web-post were studied. After obtaining the vertical shear buckling strength of a sub-model through FEM, the shear buckling coefficient k can be obtained through the back analysis. A practical calculation method for k was proposed through curving fitting the parameter study results. The elastic-plastic shear buckling strength of the web-post calculated using the proposed shear buckling coefficient k agreed well with that obtained from the FEM and test results. And it was more precise than those obtained from EC3 based on the strut model.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.12 no.5
• /
• pp.399-405
• /
• 2010

The accumulated displacements and fatigues of rock are increased by the stress-hysteresis, induced from repeated frost-thawing. Also the shear strength is decreased by them continuously. The stress-hysteresis is affected by the atmospheric temperature changes, whose behavior is visco-elasticity, usually. Therefore, to do ideal body analysis, Kelvin model could be used to analyze the frost-thawing behavior in winter. In general, rock slope failure occurs by the deterioration of rocks, which is caused by the repetition of freezing-thawing process. In order to keep the safety of such rock mass structures the deterioration process of rock needs to be described quantitatively using some meaningful parameters. In this work, the deterioration process in freezing-thawing cycle of tuff, which is a famous soft porous rock, is investigated through laboratory tests and successfully described as a differential equation for the change of porosity. And then, the deterioration of the mechanical properties of rock, such as Young's modulus and uniaxial compressive strength, are quantitatively described as a function of the porosity.

• KIPS Transactions on Computer and Communication Systems
• /
• v.7 no.6
• /
• pp.155-164
• /
• 2018

Many malicious programs have been compressed or encrypted using various commercial packers to prevent reverse engineering, So malicious code analysts must decompress or decrypt them first. The OEP (Original Entry Point) is the address of the first instruction executed after returning the encrypted or compressed executable file back to the original binary state. Several unpackers, including PinDemonium, execute the packed file and keep tracks of the addresses until the OEP appears and find the OEP among the addresses. However, instead of finding exact one OEP, unpackers provide a relatively large set of OEP candidates and sometimes OEP is missing among candidates. In other words, existing unpackers have difficulty in finding the correct OEP. We have developed new tool which provides fewer OEP candidate sets by adding two methods based on the property of the OEP. In this paper, we propose two methods to provide fewer OEP candidate sets by using the property that the function call sequence and parameters are same between packed program and original program. First way is based on a function call. Programs written in the C/C++ language are compiled to translate languages into binary code. Compiler-specific system functions are added to the compiled program. After examining these functions, we have added a method that we suggest to PinDemonium to detect the unpacking work by matching the patterns of system functions that are called in packed programs and unpacked programs. Second way is based on parameters. The parameters include not only the user-entered inputs, but also the system inputs. We have added a method that we suggest to PinDemonium to find the OEP using the system parameters of a particular function in stack memory. OEP detection experiments were performed on sample programs packed by 16 commercial packers. We can reduce the OEP candidate by more than 40% on average compared to PinDemonium except 2 commercial packers which are can not be executed due to the anti-debugging technique.