• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.05a
• /
• pp.297-302
• /
• 2002

This paper investigated the properties of flexural behavior of composite beams (end-Reinforced concrete, center-Steel concrete) according to attaching length of main bars to flange, shear reinforcing length for different types of structure. In the preceding study, structural properties of composite beams were investigated according to shear span to depth ratio, attaching method of main bars and shear reinforcing method. Based on these results, a series of experiments was carried out according to attaching length of main bar ＆ reinforcing length for different types of structure. Consequently, as attaching length of main bar and shear reinforcing length increased, composite beams represented higher strength, ductility index and stress mechanism distributed in connection zone of different types of structure.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.04a
• /
• pp.579-584
• /
• 1999

In evaluating the ultimate strength of a section for a concrete flexural member, the effect of member length is not usually considered, even though the strength tends to decrease with increase of member length. In this paper the influence of specimen length on flexural compressive strength of concrete was evaluated. For this purpose, a series of C-shaped specimens subjected to axial compression and bending moment were tested using four different length-to-depth ratios(from 1, 2, 3 and 4) of specimens with compressive strength of 58 MPa. Results indicate that the reduction in flexural compressive strength with increase of length-to-width ratios was apparent. A model equation was derived using regression analyses on the experimental data. It was also founded that the effect of specimen length on ultimate strain was negligible, but its effect of the ultimate load and the displacement at center of specimen was distinct. Finally more general model equation is also suggested.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.450-453
• /
• 1999

In this paper, The relationship between device performance and channel length(1.5-50$\mu$m) in polysilicon thin-film transistors fabricated by SPC technology was Investigated by measuring electric Properties such as 1-V characteristics, field effect mobility, threshold voltage, subthreshold swing, and trap density in grain boundary with channel length. The drain current at ON-state increases with decreasing channel length due to increase of the drain field, while OFF-state current (leakage current) is independent of channel length. The field effect mobility decrease with channel length due to decreasing carrier life time by the avalanche injection of the carrier at high drain field. The threshold voltage and subthreshold swing decrease with channel length, and then increase in 1.5 $\mu$m increase of increase of trap density in grain boundary by impact ionization.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.48 no.3
• /
• pp.190-196
• /
• 1999

Continuation power flow has been developed to remove the ill-condition problem caused by singularity of power flow Jacobian at and near at steady-state voltage instability point in conventional power flow. Continuation power flow consists of predictor and corrector. In prddictor, the direction vector at the resent solution is caluculated and the initial guess of next solution is determined at the distance of step length. The selection of step length is a very important part, since computational speed and convergence performance are both greatly affected by the choice of the step length. This paper presents the practical step length selection algorithm using the reactive power generation sensitivith. In numulation, the proposed algorithm is compared with step length selection algorithm using TVI(tangent vector index).

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.30 no.2
• /
• pp.47-54
• /
• 1998

Refining is one of the most important processes of fiber treatment that provides optical and physical properties of final paper products. The evaluation method of refining progress is usually freeness (CSF) or wetness (SR) test because of its rapidity and convenience. However, there are some deficiencies in using freeness or wetness test to evaluate pulp fibers accurately because its results are more influenced by fines contents than extent of fibers treatment. The objective of this study is to show the deficiency of wetness in evaluating the refining process. For this, beating is done by varying the beating load. Handsheets are made after beating until 25 and $32^{\circ}C$ SR, and then paper properties are measured. Refined fibers are analyzed by fiber length, fines contents, curl, kink, WRV, and zero-span tensile strength. The results show that longer beating time is required to reach the same wetness at lower beating load. There are differences in the average fiber length, distribution curve of fiber length, fines contents, curl, kink, WRV of long fiber fraction, drainage time, and zero-span tensile strength of rewetted sample at different beating load. At the low beating load in the same wetness, apparent density, breaking length, burst strength, and tear strength are higher, while opacity and air permeability are lower than those of the high beating load. Using Page s equation, which shows the relationship among tensile strength, intrinsic fiber strength, and interfiber bonding strength, interfiber bonding strength is calculated and analyzed to explain final paper properties. At $25^{\circ}C$ SR, interfiber bonding strength is only slightly higher at 2.5kgf beating load, while the intrinsic fiber strength is substantially higher. At $32^{\circ}C$ SR, intrinsic fiber strength is a little bit higher at 2.5kgf beating load, and interfiber bonding strength is remarkably higher than those of 5.6kgf beating load. These results can be used to explain the different properties of the final paper at selected beating loads.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.35 no.5
• /
• pp.72-79
• /
• 2003

Nalita wood (Trema orientalis), one of the fastest growing woods in the world, is characterized anatomical, morphological and chemical properties at annual growth ring level in order to investigate as papermaking raw material. The proportion of fibers and vessel was increased with an increase of growth ring (from pith to bark). The fiber length of Nalita was increased with increasing growth ring, and an average fiber length was about 817 um. The average basic density of Nalita was about 0.38 g/cc. The total lignin & holocellulose in Nalita were increased and ash & alcohol-benzene extract decreased from pith to bark. These values were about 23.5 - 24.4 ％, 78.1 - 80.1 ％, 1.04 - 0.92 ％ and 2.1 - 1.8 ％, respectively. The xylan was the predominant sugar in the hemicellulose of Nalita.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.38 no.4 s.117
• /
• pp.61-67
• /
• 2006

The effect of several inorganic flame-retardants such as ammonium phosphate, ammonium sulfate, aluminum hydroxide and antimony trioxide on the flame-retardant property and tensile strength of paper has been investigated. Flame-retardants were used preferably as a dry powdered mixture and added to the furnish. Both dipping and coating treatments were employed to apply flame-retardants to paper Flame-retardant paper was manufactured by treatment of $5{\sim}30%$ flame-retardants by weight of the paper on a dry weight. Paper's flame-retardant property and tensile strength were examined by comparison of char length and tensile index. As dosages of flame-retardant chemicals increased, flame-retardant property was improved but tensile index was decreased.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.33 no.1
• /
• pp.30-37
• /
• 2001

The effects of enzymatic treatment of recycled fiber were investigated to obtain the basic informations which can be used to improve the papermaking properties of recycled fiber. The recycled fibers were prepared by the repeated handsheet making and disintegrating of hardwood of hardwood and softwood kraft pulp. Novozym 342, Dinimax and Pulpzyme HC were used for enzymatic treatment. The change of fiber length distribution, freeness, contact angle and crystallinity of pulp were measured. The brightness, opacity, breaking and tear index of paper were also measured. The enzymatic treatment decreased long fiber fraction of recycled hardwood fiber, but increased long fiber fraction of recycled softwood fiber. Freeness was decreased with 0.1% enzyme and then increased again with the increase of th enzyme dosage. The improvement of flexibility of recycled fiber was obtained through the decrease of contact angle that is resulted from the decrease of crystallinity of fiber. Brightness and opacity were affected by the type of pulp and enzyme, and dosage of enzyme. Breaking length of recycled hardwood fiber was improved with enzyme treatment, but breaking length of recycled softwood fiber was decreased except for 0.01% Pulpzyme treatment. Tear index was decreased with enzymatic treatment and the lowest decrease was observed with the treatment to Pulpzyme.

• Journal of Korean Society of Forest Science
• /
• v.26 no.1
• /
• pp.1-6
• /
• 1975

This study was carried out to investigate the variation of fiber tissues of some paper mulberies (Broussnetia kazinoki Sieb.). Every twig was selected for variation from 1 year old to 4 years old of the paper mulberies growing in Woensung, Bounghwa, Euiryung and Wanju in Korea. The results are summarized as follows: 1. The length and the width of fiber tissue increase to old twigs. 2. In primary fiber tissue the variation of length increases considerably slowly, but on the contrary that of width increases very rapidly. 3. In the secondary fiber tissue the variation of length increases comparatively rapidly but that of width does not. 4. In order to investigate the fact shown from the contrary results on the fiber length and width between primary and secondary fibers, the authors calculated the correlation, coefficient and the results show comparatively higher possitive correlation coefficient.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.28 no.6
• /
• pp.707-714
• /
• 2015

In this paper, an experimental program has been conducted to investigate transfer length in high strength concrete members pretensioned through a seven-wire strand with FBG sensors. To measure transfer length, five members were fabricated, which had a length of 3 m and a cross-section of $150{\times}150mm$. It was measured that the concrete compressive strength was 58MPa at pretensioning. Test results indicated that more precise and reliable measurement on the transfer length was attained with FBG sensors than conventional gauges attached on concrete surface. Through comparing the measured transfer length and predictions, applicability of several transfer length models in literature was investigated. This paper can be useful for relevant research field such as investigation on the bond mechanism of a seven-wire strand in concrete members.