• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.38 no.1
• /
• pp.79-88
• /
• 2002

13%Cr martensitic stainless steel has been used mainly with a material for fish pre-processing machinery. However, it has not very nice cutting section because of little of the carbon content. Therefore, SUS420J2 steel that contents 0.3%C with high-strength in spite of the rust is used with a material for fish pre-processing machinery. However, studies on the corrosion characteristics of SUS420J2 steel are relatively rare. Especially, the corrosion phenomenon may cause serious degradation because the fish pre-processing machinery is exposed always to seawater environment. In this paper, the immersion corrosion test was carried out at seawater environment (pH=7.52) on SUS420J2 steel specimens that have various post-treatment conditions and its corrosion characteristics were evaluated. From test results, the specimens such as base metal, vacuum heat treatment, electrolytic polishing and tempering after quenching tend somewhat sensitive from the corrosion. In the case of vacuum heat treatment specimen of continuous immersion during 360 days, the weight loss ratio was high about seven times when compared with the different specimens. On the contrary, SUS420J2 steel specimen that has the heat treatment of tempering after quenching and the electrolytic polishing was less sensitive from the corrosion, and the weight loss ratio was very low.

• Parasites, Hosts and Diseases
• /
• v.55 no.6
• /
• pp.601-606
• /
• 2017

Cystoisospora is responsible for morbidity in immunocompromised patients. PCR is sensitive for diagnosing Cystoisospora; however, it needs reevaluation for differential molecular diagnosis of cystoisosporiasis. We aimed at evaluating melting curve analysis (MCA) after real-time PCR (qPCR) in diagnosis and genotyping of Cystoisospora as an alternative to conventional PCR. We included 293 diarrheic stool samples of patients attending the Department of Clinical Oncology and Nuclear Medicine of Cairo University Hospitals, Egypt. Samples were subjected to microscopy, nested PCR (nPCR), and qPCR targeting the internal transcribed spacer 2 region (ITS2) of the ribosomal RNA (r RNA) gene followed by melting temperatures ($T_ms$) analysis and comparing the results to PCR-RFLP banding patterns. Using microscopy and ITS2-nPCR, 3.1% and 5.8% of cases were Cystoisospora positive, respectively, while 10.9% were positive using qPCR. Genotyping of Cystoisospora by qPCR-MCA revealed 2 genotypes. These genotypes matched with 2 distinct melting peaks with specified $T_ms$ at $85.8^{\circ}C$ and $88.6^{\circ}C$, which indicated genetic variation among Cystoisospora isolates in Egypt. Genotype II proved to be more prevalent (65.6%). HIV-related Kaposi sarcoma and leukemic patients harbored both genotypes with a tendency to genotype II. Genotype I was more prevalent in lymphomas and mammary gland tumors while colorectal and hepatocellular tumors harbored genotype II suggesting that this genotype might be responsible for the development of cystoisosporiasis in immunocompromised patients. Direct reliable identification and differentiation of Cystoisospora species could be established using $qPCR-T_ms$ analysis which is useful for rapid detection and screening of Cystoisospora genotypes principally in high risk groups.

• Journal of Embryo Transfer
• /
• v.13 no.2
• /
• pp.173-178
• /
• 1998

The objective of this study was to evaluate the embryonic development ability and the appearance of blastocysts of bovine in vitro fertilized oocytes cultured in different culture media, and also to evaluate survival rate after thawing of frozen embryos by using 1.5 or 1.8M ethylene glycol(EG) with sucrose or trehalose. Fertilized oocytes were divided into three groups; i ) monolayer of cumulus /granulosa cell prepared by TGM 199+5% calf serum(TGM199), ii)GRlaa+5% CS, iii)SOF+5% CS, and they were cultured after insemination for 9 days, at 39˚C, under 5% $CO_2$ in air, but SOF+5% CS was cultured at 39˚C, under 5% 02, 5% GO2, 99% N2. Blastocysts derived from GRlaa + 5% CS on day 7~8 after insemination were frozen by using 1.5M EG or 1.8M EG with/without 0.2M sucrose or O.1M trehalose. The development rate of blastocysts on day 7 after insemination in SOF+5% CS was significant higher than in TCM199 or CR1aa(P<0.05). The appearance rate of blastocysts on day 7-8 after insemination was higher than in TCM199, when fertilized oocytes were cultured in GRlas or SOF. The survival rate of frozen blastocysts after thawing tended to increase, when blastocysts were frozen by using 1.8M EG with 0.2M sucrose or O.1M trehalose. These results indicated that SOF or CRlaa media with amino acids was superior to TCM199 with monolayer in terms of blastocyst development in culturing of in vitro fertilized bovine nocytes, and sucrose or trehalose was supposed to prevent embryos from the freezing shock.

• The Journal of the Korean bone and joint tumor society
• /
• v.2 no.1
• /
• pp.72-77
• /
• 1996

Metastaic bone tumors are usually accompanied with severe pain. The treatment modalities for this pain are so variable that patients are sometimes afraid of using them. Salmon calcitonin has a function to increase beta-endorphines followed by increasing the blood level of prostaglandin and thromboxan A2, which results in analgesic effect. This drug also has been known to decrease bone resorption. There were a few reports that parenteral use of salmon calcitonin decrease the pain from metastatic bone tumor. We wanted to know the effectiveness and tolerability of nasal spray of salmon calcitonin in relieving bone pain with metastatic tumor. We analyzed the effectiveness in the aspects of pain, sleep, performance status, mobility, supplementary analgesic use. The biologic effect of salmon calcitonin was analysed with CBC, Ca/P, BUN/Cr, uric acid. Simple radiography, alkaline phosphatase, osteocalcin, pyrilink-K were used as parameters for bone change. Eighteen cases of metastatic bone tumors took nasal spray of salmon calcitonin($Miacalcic^{(R)}$, 200IU/day) for 4 weeks, to relieve bone pain. With Wilcoxon Matched-Pairs Signed Ranks Test, we could find pain decreased significantly at 3 week and mobility become improved at 4 week of salmon calcitonin use. Other parameters didn't show any significant changes. We think the analgesic effect is mainly due to effect not on the local bone lesion but on the central nervous system, and that increased dose of salmon calcitonin can induce earlier and stronger analgesic effect.

• Journal of Environmental Health Sciences
• /
• v.33 no.4
• /
• pp.276-282
• /
• 2007

The purpose of this study is to assess the accurate state of the following: total welding fumes versus welding fumes in the air, respirable particulate mass, and exposure of dockyard welders to heavy metals. In addition, this study provides basic data for proposing improvements to create efficient and appropriate welding environments and to prevent occupational diseases. The subjects of this study were 94 laborers who worked at the block construction sites of large-scale dockyards located in Gyeongnam Province from March 2005 to June 2005. In order to collect samples on total welding fumes in the air and respirable particulate mass from the welders, Methods 0500 and 0600, established by the National Institute for Occupational Safety and Health (NIOSH), were used. The metals within the welding fumes were also analyzed using Inductively Coupled Plasma (ICP) under Method 7300 from NIOSH. The results of this research are summarized below. The geometric mean concentration of total welding fumes and that of respirable particulate mass were $4.11\;mg/m^3\;and\;3.53\;mg/m^3$, respectively. As a result of comparing the two measurement methods, there were significant differences (p<0.05) between the two groups for Ca, Cu, Cr, and Ni; however, there were no differences in Fe, Mg, Zn, Mg, Pb, and Cd. As a result of the analysis, the correlation between Mn and the concentration of heavy metals in the total welding fumes and respirable particulate mass was found to be -0.29, a significant negative correlation. The correlation between other heavy metals, however, was low. Finally, in the same total welding fumes, the correlation of Fe and Mg was high.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.6 s.177
• /
• pp.1398-1407
• /
• 2000

The structural steels of power plant show the decrease of mechanical properties due to degradation such as temper embrittlement, creep damage and softening during long-term operation at high temper ature. The typical causes of material degradation damage are the creation and coarsening of carbides(M23C6, M6C) and the segregation of impurities(P, Sb and Sn) to grain boundary. It is also well known that material degradation induces the cleavage fracture and increases the ductile-brittle transition temperature of steels. So, it is very important to evaluate degradation damage to secure the reliable and efficient service condition and to prevent brittle failure in service. However, it would not be appropriate to sample a large test piece from in-service components. Therefore, it is necessary to develop a couple of new approaches to the non-destructive estimation technique which may be applicable to assessing the material degradation of the components with not to influence their essential strength. The purpose of this study is to propose and establish a new electrochemical technique for non-destructive evaluation of material degradation damage for Cr-Mo steels which is widely used in the high temperature structural components. And the electrochemical anodic polarization test results are compared with those of semi-nondestructive SP test.

• Korean Journal of Soil Science and Fertilizer
• /
• v.45 no.4
• /
• pp.565-571
• /
• 2012

This study was conducted to investigate the tolerance of some resistant fungal strains from soils contaminated with heavy metals. Various fungal strains were isolated from soil samples collected from studied sites which heavy metals and other pollutants have been emitted in effluents for several years. Fungi isolated belong to different genera; however, Penicillium spp. showed the most frequent species. The microbial number was remarkably higher in the control soil than contaminated soil samples collected from mining areas. $Pb^{2+}$ and $Zn^{2+}$ had the highest concentration in the polluted soils ranging from 89 - 3,521 ppm and 98 - 4,383 ppm, respectively. The minimum inhibition concentrations (MICs) of $Pb^{+2}$ and $Zn^{+2}$ showed the highest values against the fungal strains. $Ni^{+2}$ and $Co^{+2}$ were the lowest contaminants in the polluted soils with the concentration of 5 to 12.1 ppm and 1.8 to 4.8 ppm, respectively. The tested resistant strains showed the strongest inhibition for $Ni^{+2}$ and $Co^{+2}$ up to 200-400 ppm. Cadmium was the most highly toxic heavy metal for most of strains, however, 1 mM of $Cr^{3+}$, $Cu^{2+}$ and $Pb^{2+}$ accelerated the growth of Penicillium verrucosum KNU3. $Cu^{+2}$ and $Zn^{+2}$ at concentration of 1 mM did not affect the growth rate P. funiculosum KNU4. Tolerance of fungal species to heavy metals appears to be strain and origin dependent.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.4
• /
• pp.438-444
• /
• 2005

This study is to install the flexible vertical in order to separate not only the time but also the space in the single reactor by opening and closing the flexible vertical, and to intensify the aerobic, anaerobic and anoxic reactions by reducing the time to activate the microorganism for nitrification, denitrification, release of organic phosphate and luxury uptake of ortho-phosphate. Eventually the result of this study obtained each 90.9%, 76.4% for the removal efficiency of total nitrogen and phosphate. Also, content rate of phosphate at excess sludge was higher $25{\sim}30%$ for SBR reactor with the flexible verticals than existing SBR process. It would be concluded that SBR reactor with flexible verticals is promising for nitrogen and phosphate removal conditions than conventional SBR processes.

• Journal of Powder Materials
• /
• v.12 no.6 s.53
• /
• pp.399-405
• /
• 2005

Nanopowders of titanium dioxide $(TiO_2)$ incorporating the transition metal element(s) were synthesized by flame synthesis method. Single element among Fe(III), Cr(III), and Zn(II) was doped into the interior of $TiO_2$ crystal; bimetal doping of Fe and Zn was also made. The characteristics of transition-metal-doped $TiO_2$ nanopowders in the particle feature, crystallography and electronic structures were determined with various analytical tools. The chemical bond of Fe-O-Zn was confirmed to exist in the bimetal-doped $TiO_2$ nanopowders incorporating Fe-Zn. The transition element incorporated in the $TiO_2$ was attributed to affect both Ti 3d orbital and O 2p orbital by NEXAFS measurement. The bimetal-doped $TiO_2$ nanopowder showed light absorption over more wide wavelength range than the single-doped $TiO_2$ nanopowders.

• Journal of Korean Society for Atmospheric Environment
• /
• v.27 no.5
• /
• pp.523-533
• /
• 2011

This study had the aim of characteristics of $PM_{10}$ in subway cabins. $PM_{10}$ was measured by times of day (rush and non rush hours) and seasons with real time $PM_{10}$ sampler on the subway cabins of line 7. Filter samples were collected for evaluation of their elemental composition as well as identification of major sources of $PM_{10}$ using a receptor model, PMF. $PM_{10}$ concentration were the highest in the winter season both in the rush and non rush hours at 152.8 ${\mu}g/m^3$, 90.2 ${\mu}g/m^3$ respectively. The $PM_{10}$ concentrations in rush hour were 30% higher compared to non rush hours. Based on the chemical information, the composition rare of inorganic elements was 52.5%, anions were 10.2% and others were 37.3%. Fe was the most abundant element and significantly correlated (p.0.01) with Mn (r=0.97), Ti (r=0.91), Cr (r=0.88), Ni (r=0.89) and Cu (r=0.88). Characterized $PM_{10}$ sources by PMF in the cabin were soil and road dust related sources (27.2%), railroad related sources (47.5%), secondary nitrate sources (16.2%) and a Cl-factor mixed with a secondary sulfate source (9.1%).