• Corrosion Science and Technology
• /
• v.21 no.1
• /
• pp.53-61
• /
• 2022

Alloys of Fe-(5.3-29.8)%Mn-(1.1-1.9)%Al-(0.4-0.5)%C were oxidized at 550 ℃ to 650 ℃ for 20 h to understand effects of alloying elements on oxidation. Their oxidation resistance increased with increasing Mn level to a small extent. Their oxidation kinetics changed from parabolic to linear when Mn content was decreased and temperature was increasing. Oxide scales primarily consisted of Fe₂O₃, Mn₂O₃, and MnFe₂O₄ without any protective Al-bearing oxides. During oxidation, Fe, Mn, and a lesser amount of Al diffused outward, while oxygen diffused inward to form internal oxides. Both oxide scales and internal oxides consisted of Fe, Mn, and a small amount of Al. The oxidation of Mn and carbon transformed γ-matrix to α-matrix in the subscale. The oxidation led to the formation of relatively thick oxide scales due to inherently inferior oxidation resistance of alloys and the formation of voids and cracks due to evaporation of manganese, decarburization, and outward diffusion of cations across oxides.

• Bulletin of the Korean Chemical Society
• /
• v.30 no.12
• /
• pp.3095-3097
• /
• 2009

• 한국연소학회:학술대회논문집
• /
• 2007.05a
• /
• pp.161-167
• /
• 2007

Gasification characteristics in the fluidized bed reactor are essential for the design of a gasification furnace to optimize the operation condition. Moisture content of the solid fuel is one of the important factors to influence directly the gasification characteristics. So it is necessary to investigate the effect of moisture content of solid fuel in gasification process. Gasification characteristics are investigated with results from thermogravimetric analyser and lab-scale fluidized bed reactor for wood and RDF samples along with changing moisture contents. Additionally lab-scale fluidized bed reactor was run continuously and gas concentrations at the exit were measured. It is observed that the rate of reaction in partial oxidation condition is in between the results from the combustion environment and from the inert condition. Moisture content in a particle slows down the heating rate of a particle. So, reaction time is delayed by the moisture content. However, RDF samples that are easy to break-up doesn't show the effect of moisture content. The results of continuous operation condition shows that proper moisture content promotes gasification because steam from the particles helps gasifcation of the sold fuel.

• Korean Journal of Materials Research
• /
• v.29 no.1
• /
• pp.7-10
• /
• 2019

Cr-Al alloys are attracting attention as oxidation resistant coating materials for high temperature metallic materials due to their excellent high temperature stability. However, the mechanical properties and oxidation resistance of Cr-Al alloys can be further enhanced, and such attempts are made in this study. To improve the properties of Cr-Al alloys, Si is added up to 5 wt%. Casting specimens with different amounts of Si content are prepared by a vacuum arc remelting method and isothermally heated under steam conditions at $1,100^{\circ}C$ for 1 hour. The as-cast microstructure of low Si alloys is mainly composed of only a Cr phase, while $Al_8Cr_5$ and $Cr_3Si$ phases are also observed in the 5 % Si alloy. In the high Si alloy, only Cr and $Cr_3Si$ phases remain after the isothermal heating at $1,100^{\circ}C$. It is found that Si additions slightly decrease the oxidation resistance of the Cr-Al alloy. However, the microhardness of the Cr-Al alloy is observed to increase with an increasing Si content.

• Journal of the Korean Wood Science and Technology
• /
• v.48 no.2
• /
• pp.231-244
• /
• 2020

As a way of finding value-added materials from waste medium density fiberboard (MDF), this study characterized cellulose nanocrystals (CNCs) isolated by ammonium persulfate (APS) oxidation using recycled MDF fibers. Chemical composition of the recycled MDF fibers was done to quantify α-cellulose, hemicellulose, lignin, nitrogen, ash and extractives. The APS oxidation was performed at 60 ℃ for 16 h, followed by ultrasonication, which resulted in a CNC yield of 11%. Transmission electron microscope images showed that rod-like CNCs had an average length and diameter of 167±47 nm and 8.24±2.28 nm, respectively, which gave an aspect ratio of about 20. The conductometric titration of aqueous CNCs suspension resulted in a carboxyl content of 0.24 mmol/g and the degree of oxidation was 0.04. Attenuated total reflection Fourier transform infrared (ATR-FTIR) spectroscopy clearly showed the presence of carboxyl group on the CNCs prepared by the APS oxidation. The change of pH of the aqueous CNC suspension from 4 to 7 converted the carboxyl group to sodium carboxylate group. These results showed that the APS oxidation was facile and CNCs had a one-step preparation method, and thus suggested an optimization of the oxidation condition in future.

• 연구논문집
• /
• s.29
• /
• pp.141-149
• /
• 1999

Brazing of Fe-Cr-Al alloy was carried out at $1200^{\circ}C$ in vacuum furnace using nickel-based filler metals : BNi-5 powder(Ni-Cr-Si-Fe base alloy} and MBF-50 foil (Ni-Cr-Si-B). The effect of boron content on the stability of oxide scale on the brazed joint was investigated by means of cyclic oxidation test performed at $1050^{\circ}C$ and $1200^{\circ}C$. Apparently, the joints brazed with MBF-50 containing boron showed relatively stable oxidation rates compared to boron-free BNi-5 at both temperatures. However, it was considered that the slower weight loss of MBF-50 brazed specimen wasn’t resulted from the low oxidation rate but from the spallation of oxide layer. The oxide layer consisted of thick spinel oxide on the surface and $Al_2 O_3$ internal oxide layer along the interface between mother alloy and braze, the mother alloy was also eroded seriously by the formation of spinel oxides such as $FeCr_2 O_4$ and $NiCr_2 O_4$ on the surface, likely to be induced by the change of oxide forming mechanism due to diffusion of boron from the braze. On the contrary, the joint brazed with BNi-5 showed the good oxidation resistance during the cyclic oxidation test. It seems that the oxidation can be retarded by the formation of stable $Al_2 O_3$ layer at the surface.

• Food Science of Animal Resources
• /
• v.32 no.4
• /
• pp.491-496
• /
• 2012

The objective of this research was to investigate the effect of the fattening period (18, 21, and 24 mon) on the oxidative stability of Holstein beef patties. The ground Holstein steer beef samples (M. longissimus dorsi) were stored at $4^{\circ}C$ for 12 d and used for lipid oxidation, protein oxidation, myoglobin oxidation, and color measurements. Fat content was significantly (p<0.05) higher in the 24 mon group than in the 18 mon group. 2-thiobarbituric acid reactive substances content and metmyoglobin concentration were the highest (p<0.05) in the 24 mon group from 8 d of storage. Conjugated dienes content was significantly (p<0.05) higher in the 21 and 24 mon groups. Carbonyl content was the highest (p<0.05) in the 24 mon group at 12 d of storage. In surface meat color, the CIE $L^*$ value showed a lower level in the 21 and 24 mon groups from 4 d of storage. Although the CIE $a^*$ value was further lowered, the CIE $b^*$ value maintained a higher value in the 24 mon group during storage, compared to the other groups. Therefore, greater fattening period increased lipid oxidation, protein oxidation, and myoglobin oxidation in Holstein beef patties. Partially, the 24 mon group had the lowest oxidative stability.

• Korean Journal of Materials Research
• /
• v.12 no.8
• /
• pp.676-681
• /
• 2002

Microstructure, mechanical properties, and oxidation resistance of TiAIN thin films deposited on quenched and tempered STD61 tool steel by arc ion plating were studied using XRD, XPS and micro-balance. The TiAIN film was grown with the (200) orientation. The grain size of TiAIN thin film decreased with increasing Al contents, while chemical binding energy increased with Al contents. When hard coating films were oxidized at $850^{\circ}C$ in air, oxidation resistance of both TiN and TiCN films became relatively lower since the surface of films formed non-protective film such as $TiO_2$. However, oxidation resistance of TiAIN film was excellent because its surface formed protective layer such as $_A12$$O_3$ and $_Al2$$Ti_{7}$$O_{15}$, which suppressed oxygen intrusion.

• Journal of the Korean Ceramic Society
• /
• v.34 no.4
• /
• pp.413-419
• /
• 1997

The specimens which were prepared from cokes with additions of 0~25 wt% B4C were sintered in Ar atmosphere at 220$0^{\circ}C$. The effects of B4C content on graphitization and oxidation resistance of cokes were investigated. B4C accelerates the graphitization of cokes and at 220$0^{\circ}C$ the degree of graphitization increased from 0.33 which is the value of pure carbon to 0.56, which increased bluk density and porosity. Especially bending strength increased as th graphitization temperature increased. Oxidation resistance property was greatly improved when B4C was added more than 10wt% at 80$0^{\circ}C$ and when B4C was added more than 20wt% at 100$0^{\circ}C$. This was because that the thin layer of B2O3 glass phase on the surface of the composite could be identified to increase the oxidation resistance.

• Journal of the Korean Applied Science and Technology
• /
• v.6 no.1
• /
• pp.9-14
• /
• 1989

Effectiveness of some natural antioxidants were investigated by measuring the physico-chemical charcteristics and fatty acid composition during thermal oxidation in palm oil. Tocopherol showed most enhanced thermal oxidation stabilities compared to the other natural antioxidants. AR spice was no good AOM stability and changes of acid value but the other parameters were obtained desirable results. The changes of linoleic aicd content was slightly decreased during thermal oxidation. Addition of rosemary and glycyrriza extract increased the stabilities of oil less than tocopherol and AR spice. Order of antioxdative effects was tocopherol, AR spice and others. There was no significiant difference in stability of rosemary and glycyrriza extract.