• Journal of Advanced Marine Engineering and Technology
• /
• 제29권7호
• /
• pp.744-749
• /
• 2005

This paper describes the performance improvement of power control system of magnetron (MGT) for microwave oven. The MGT is used extensively in household microwave oven and industrial microwave heating devices, and is operated by 3.0[kV] $\∼$5.0[kV] dc high voltage. The proposed power supply is consisted of a bridge rectifier, step-up converter(SUC) and its controller, half bridge inverter(HBI) and its controller, and full wave double voltage rectifier(DVR). In the proposed system, a good power factor can be obtained by the SUC' switching method that the inductor current waveforms follows that of the rectified voltage, and a line input power can be controlled to a range of 17.5[$\%$] by duty ratio (DR) adjustment of the HBI.

• Journal of Welding and Joining
• /
• 제15권6호
• /
• pp.105-115
• /
• 1997

A numerical study is performed to predict the thermal response of a detailed card assembly during infrared reflow soldering. The card assembly is exposed to discontinuous infrared panel heater temperature distributions and high radiative/convective heating and cooling rates at the inlet and exit of the oven. The convective, radiative and conduction heat transfer within the reflow oven as well as within the card assembly are simulated and the predictions illustrate the detailed thermal responses. The predictions show that mixed convection plays an important role with relatively high frequency effects attributed to buoyancy forces, however the thermal response of the card assembly is dominated by radiation. The predictions of the detailed card assembly thermal response can be used to select the oven operating conditions to ensure proper solder melting and minimization of thermally induced card assembly tresses and warpage.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 제5회 압연심포지엄 신 시장 개척을 위한 압연기술
• /
• pp.249-257
• /
• 2004

Drying and curing characteristics of PCM resins using the induction heater and short-wave infrared emitter module was studied to develop a compact oven system for the high speed CCL and post-treatment equipment. Drying of the polyester resins using the induction heater and infrared heater showed that the blistering tendency of polyester resin coating increased regardless of additives and colors of resins as the heating rate and/or dry film thickness increased. The blistering of polyester resin coating layer occurred when the heating speed was over than $25^{\circ}C/sec$ for the dry film thickness of $19\~20um$, which is the typical thickness of finish coating in CCL. So did it when the heating speed was over than $40^{\circ}C/sec$ for the dry film thickness over than 10 um. The heating efficiency of paint coated steels by the infrared heating was strongly dependent on the colors of paint coating and generally increased for the dark surface and/or coating. But the faster drying of the PCM resin coatings increased the blistering tendency of coating layer. The blistering limit for the typical finish coating by the infrared heating was estimated as the heating rate slower than $20^{\circ}C/sec$ regardless of colors of PCM resins.

• 한국기계가공학회지
• /
• 제19권5호
• /
• pp.67-74
• /
• 2020

To predict the thermal deformation of an oven cabinet during the enamel process, we propose a simple finite element analysis method comprising two steps: heating and cooling. To this end, the basic mechanical and thermal properties such as thermal expansion of the enamel and steel plate were experimentally studied, and the mechanical properties of four different stainless steel (SUS) plates were evaluated to select the target material for the oven at high temperature conditions from 400 ℃ to 700 ℃. In the first analysis step of the enamel process, the SUS plate was heated to 850 ℃ and was then thermally expanded without considering the enamel coating. Next, assuming the perfect bonding of two materials (enamel coating and metal plate), the enamel plate was allowed to cool to room temperature till 22 ℃. From the results of comparing the experimental and analytical data, we can make a conclusion that the proposed method can be applied to evaluate the thermal deformation of enamel products. Especially, the thermal deformation of the oven can be predicted with different enamel coating conditions, such as uniform and nonuniform coating thickness.

• 한국식품영양과학회지
• /
• 제27권3호
• /
• pp.489-494
• /
• 1998

For the purpose of improving the qualities of popcorn, potato, frozen hotdog and steamed egg, the effects of food height(0mm: HO, 5mm: H5, 10mm, 15mm: H15) for microwave cooking on physicochemical properties were investigated. In popcorn, weight loss was decreased as height increased while volume of popcorn was increased, which indicated that popcorn was poped very well as height increased. H10 showed the highest taste score in sensory evaluation. In potato, degree of gelatinization was increased as hight increased. H10 showed the highest overall acceptance score. In frozen hotdog, hardness of hotdog was decreased as hight increased and H15 showed the lowest hardness score (408.8g). In steamed egg, H5 showed the highest temperature and H10 showed the highest overall acceptance score. Physicochemical properties of food were changed by heating height of microwave heating.

• 한국대기환경학회지
• /
• 제25권2호
• /
• pp.122-132
• /
• 2009

Adsorption of toluene by activated carbon fiber (ACF) coated with dielectric heating element and desorption by applying microwave were investigated. In order to prepare adsorbent so that VOC can be desorbed by microwave heating, fine dielectric heating element with nano size was coated on the surface of the ACF using hybrid binder. Eight adsorbents (ACF-DHE, Activated Carbon Fiber coated with Dielectric Heating Element) were prepared with different amount of dielectric heating element, kinds of hybrid binder, and solvent. In order to investigate adsorption characteristics, BET surface area, pore volume, and average pore size were measured for each adsorbent including ACF. Breakthrough experiments with toluene concentration, flow rate, bed length using fixed bed reactor were performed to investigate adsorbality of adsorbent, and results were compared with that of the ACF. Desorption reactor was constructed with modified microwave oven to investigate heating effect on ACF-DHE by applying microwave power. Each adsorbent saturated with toluene were put into desorption reactor. Composition of desorbed gas generated by applying controlled microwave power to reactor was measured. Up to now, hot air desorption method has been used. Experimental results showed that desorption method with new adsorbent prepared by coating dielectric heating element on ACF can be used for industrial application.

• 한국식품과학회지
• /
• 제31권6호
• /
• pp.1583-1588
• /
• 1999

마늘의 향미를 조절하기 위하여 박피하지 않은 마늘쪽을 $60^{\circ}C{\sim}90^{\circ}C$의 범위에서 30분간 예열처리한 경우와 전자레인지로 10초간 가열한 경우에 마늘의 향미성분변화를 조사한 결과는 다음과 같다. 마늘의 향기성분은 예열처리 온도가 상승함에 따라 감소하였고, $70^{\circ}C,\;80^{\circ}C$ 및 $90^{\circ}C$에서 30분간 예열처리하면 대조구에 비하여 각각 20%, 31% 및 49% 감소하였다. 전자레인지로 10초간 가열한 경우에는 열풍건조기에서 $70^{\circ}C{\sim}80^{\circ}C$에서 가열한 것과 유사한 경향을 보였다. 열풍건조기로 예열처리하면 glucose, fructose 및 fructooligosaccharide가 감소하였으며, 이런 감소는 온도가 높을수록 컸으며 fructooligosaccharide 보다는 단당류인 glucose와 fructose에서 더욱 컸다. 전자레인지로 가열처리한 경우에는 열풍건조기로 예열처리한 경우에 비하여 유리당의 변화가 현저히 적었다. Alliin의 분해산물로 알려진 pyruvic acid는 예열처리 온도가 증가할수록 감소하는 경향을 나타내었고, 그 밖의 유기산은 유의적 변화가 없었다. 마늘의 주요 아미노산인 arginine은 열풍에 의한 예열처리시 감소하였으나 전자레인지로 가열한 경우에는 감소하지 않았고, glutamic acid와 tyrosine은 모든 처리구에서 감소하였다.

• 한국식품저장유통학회지
• /
• 제4권2호
• /
• pp.173-180
• /
• 1997

The effects of sugars and heating methods on the sugar infilteration, hardness, color and organoleptic characteristics were investigated for quality improvement of sugared chestnuts. Among the tested sugars, isomaltooligosugar was the most effective on the rate of sugar infilteration. High temperature increased the rate of sugar infilteration during sugaring process, but color and flavor were deteriorated at 9$0^{\circ}C$. The most suitable temperature for sugaring process was 7$0^{\circ}C$. The product sugared with fructooligosugar recoreded the highest score in hardness, odor and preference than any other sugars tested and increased the rate of sugar infilteration when mixed with sugar at same amount. The changes of soluble solids in chestnuts boiled with microwave oven were ranged from 18。Brix to 32。Brix, while chestnuts heated in general were from 18。Brix to 28。Brix. Chestnuts boiled with microwave heating were sugared rapidly. The hardness of boiled and sugared chestnuts was lower when treated with microwave than with general heating. Hunter's L and b value of sugared chestnut treated with microwave decreased during processing but a value somewhat increased.

• 한국산업융합학회 논문집
• /
• 제3권4호
• /
• pp.345-351
• /
• 2000

The change of crystalline structure of drawn PP filaments were investigated. Samples were treated by isothermally annealed after elevated heating from $20^{\circ}C$. Measurements were carried out with XRD for crystallite size and density gradient tube for crystallinity. Isothermally heat treatment were carried out at the temperature of $100^{\circ}C$, $120^{\circ}C$ and $140^{\circ}C$ for 10min., 30min. and 60min. in dry oven. The isothermal heat treatment after elevated heating from $20^{\circ}C$ were carried out at the temperature of $100^{\circ}C$, $120^{\circ}C$ and $140^{\circ}C$ for 10min., 30min. and 60min. with heating rate of $1^{\circ}C$/min., $5^{\circ}C$/min. and $10^{\circ}C$/min. From the results of this study, it found the following facts. It was found that the crystallinity and crystallite size of (110) plane of sample were increased with increasing of annealed temperature and time. Also crystallinity and crystallite size of samples which were isothermally annealed after elevated heating from $20^{\circ}C$ were higher than those of isohtermally annealed samples.

• 보존과학회지
• /
• 제19권
• /
• pp.31-42
• /
• 2006

토기나 자기의 결손부분을 복원할 때 사용되는 재료들은 매우 다양하며 각 재질들의 특성에 따라 사용되고 있는 상태이다. 본 연구에서는 기존에 사용되어 오던 복원재료들이 가지고 있는 여러 문제점들을 인식하여 이를 해결할 수 있는 새로운 복원재료들을 찾고자 하였다. 본 실험연구에서는 기존에 복원재료로 많이 사용되어 오던 에폭시퍼티에 소성점토를 적정 비율로 혼합한 신복원재료로 황변도, 경도, 채색성, 그리고 소성온도에 대한 실험을 함으로써 이 재료가 복원의 작업성, 황변정도, 채색성 등에서 매우 좋은 재료임을 확인할 수 있었다.