• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.05a
• /
• pp.838-841
• /
• 2004

This paper presents the experimental results on the penetration of chloride. ions to ordinary portland cement concrete which is subjected to 2 different artificial environments; consecutive digestion, wetting at $3\%$ NaCl for 1 day and then drying at $40^{\circ}C$ oven for 4 days. The water-cement ratio was $35\%,\;45\%,\;55\%$. Test results showed that the intrusion depth and concentration of chloride ions penetrated into concrete in repeated wetting-drying environments were respectively deeper and higher than those of consecutive digestion environment. The penetration of chloride ions deeply depend on the effect of water to cement ratio.

• Journal of Biosystems Engineering
• /
• v.13 no.3
• /
• pp.52-58
• /
• 1988

This study was conducted to develop a grain moisture content measurement sensor for automatic control of rough rice drying by natural air. For the above objective, the electrod type sensor was designed and tested. The sensor was able to produce electrical resistance which changes with moisture content of grain. An A/D converter and a micro-computer wed for processing measurement data of sensor. The developed sensor satisfied most design requirements and the results of statistical analysis show that there it no difference between the measurement method of sensor developed and of the dry-oven. Using the developed sensor and measurement system, we are able to measure moisture content of rough rice automatically in drying by natural air.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.08a
• /
• pp.249-257
• /
• 2004

Drying and curing characteristics of PCM resins using the induction heater and short-wave infrared emitter module was studied to develop a compact oven system for the high speed CCL and post-treatment equipment. Drying of the polyester resins using the induction heater and infrared heater showed that the blistering tendency of polyester resin coating increased regardless of additives and colors of resins as the heating rate and/or dry film thickness increased. The blistering of polyester resin coating layer occurred when the heating speed was over than $25^{\circ}C/sec$ for the dry film thickness of $19\~20um$, which is the typical thickness of finish coating in CCL. So did it when the heating speed was over than $40^{\circ}C/sec$ for the dry film thickness over than 10 um. The heating efficiency of paint coated steels by the infrared heating was strongly dependent on the colors of paint coating and generally increased for the dark surface and/or coating. But the faster drying of the PCM resin coatings increased the blistering tendency of coating layer. The blistering limit for the typical finish coating by the infrared heating was estimated as the heating rate slower than $20^{\circ}C/sec$ regardless of colors of PCM resins.

• Journal of the Korean Wood Science and Technology
• /
• v.31 no.4
• /
• pp.57-62
• /
• 2003

The Mechanical and drying characteristics of Pinus densiflora wood, which was damaged by forest fire, and sound wood were examined. There were no significant differences in axial compressive properties, shearing strength and impact bending absorbed energy between damaged and sound woods. But the bending properties of damaged wood were slightly higher than those of sound wood. The green moisture content of sapwood in damaged wood was lower than that in sound wood, but oven-drying rate was similar in both woods. Number of initial check in damaged wood was smaller than that in sound wood, and inner check in damaged and sound woods was not observed. Consequently, it is considered that mostly damaged wood by forest fire can be used for wood material after removing the bark.

• Journal of Forest and Environmental Science
• /
• v.12 no.1
• /
• pp.1-12
• /
• 1996

This study was carried out to estimate drying schedule of Fagaceae four species grown in Kangwon-Do by oven-drying at $100^{\circ}C$ which aimed to elucidate the characteristics such as current moisture content, drying process, initial check, collapse and internal check during drying following each board thickness (1.5cm, 2.5cm, 3.5cm, 4.5cm). The results were as follows; Current moisture content of each board showed a rapid drying curve with the high initial moisture content of board. With the high initial moisture content, the incease of board thickness and the slowness of changing rate of moisture content, species took long to do drying. Also, the initial conditions of drying had to be mild condition with the increase of board thickness.

• Journal of Biosystems Engineering
• /
• v.1 no.1
• /
• pp.55-55
• /
• 1976

An experimental work was conducted to develop an optimum operating system of various hay drying systems ; sun-drying with long hay, sun-drying after chopping, sun-drying after crushing, heated air drying after chopping using batch-type dryer and heated air drying after crushing using tunnel-type dryer. Seombody having 60 cm long and initial moisture content of approximately 79 % in wet basis was used for the experiment. The criteria selected for determining the optimum operating condition were the drying performance rate, the production cost and quality of dried matter of each drying systems. The result of this study are summarized as follows : 1. Drying characteristics of leaves of long stem hay, chopped seombody and crushed one were obtained by maintaining the oven temperature at 70 degrees centigrade. The required drying times for various samples to approximately 15% moisture content in wet basis were about 50 min .for leaves ; 160 min. for crushed hay ; 250 min. for chopped hay ; 340min. for ling hay and more than 360 min .for stems. The drying time of crushed hay was required about 50 % of that for the uncrushed long hay. Such a significant difference of drying of time between the leaf and long stem may indicate that an effective drying of seombody may not be achieved unless any kind of special process treatment for the whole hay is undertaken. 2. In each individual drying system, the following conclusions were drawn: a. After 8 days sun-drying on concrete floor under good days with average tempe?rature at $256{\circ}C$ and relative humidity at 55% at 2 P.M., the moisture content of long hay was still above 25 5'~ and the leaf loss during drying caused by wind and rough handling was more than 50 ~G. b. It was possible to dry the chopped seombody by sun-drying down to about 10 % moisture content within 5 days, however, a stock of heat and discolouration phenomena were observed during the drying, which may be due to the increased deposit-density by chopping, resulting in lowering the quality of the dried product. c. Sun-drying for the crushed material by hay-conditioner was required about 4 days to reduce the moisture content to about 10 %, keeping the quality of dried product at good grade. o. The optimum deposit-depth of the chopped seombody in the batch-type dryer used was about 28cm with about 42kg/hr of drying performance rate. However, it was necessary to overturn the materials between the upper and lower layers in order to obtain a good quality of dried product. d. The drying performance rate by the tunnel-type drier was highest among those of drying systems tested, giving the rate of approximately 400kg/day. 3. On reviewing the individual drying system for seombody, it was possible to draw conclusion that the best system was tunnel drying with the crushed seombody as far as the performance rate was concerned. However, the methods gives the highest operational cost. The system for the lowest operational cost with good quality of dried product was the sun-drying with the crushed material. Accordingly, it may be recommended that the system of sun-drying for the crushed seombody may be the most feasible system presently applicable to farm-level operation.

• Journal of Biosystems Engineering
• /
• v.1 no.1
• /
• pp.56-63
• /
• 1976

An experimental work was conducted to develop an optimum operating system of various hay drying systems ; sun-drying with long hay, sun-drying after chopping, sun-drying after crushing, heated air drying after chopping using batch-type dryer and heated air drying after crushing using tunnel-type dryer. Seombody having 60 cm long and initial moisture content of approximately 79 % in wet basis was used for the experiment. The criteria selected for determining the optimum operating condition were the drying performance rate, the production cost and quality of dried matter of each drying systems. The result of this study are summarized as follows : 1. Drying characteristics of leaves of long stem hay, chopped seombody and crushed one were obtained by maintaining the oven temperature at 70 degrees centigrade. The required drying times for various samples to approximately 15% moisture content in wet basis were about 50 min .for leaves ; 160 min. for crushed hay ; 250 min. for chopped hay ; 340min. for ling hay and more than 360 min .for stems. The drying time of crushed hay was required about 50 % of that for the uncrushed long hay. Such a significant difference of drying of time between the leaf and long stem may indicate that an effective drying of seombody may not be achieved unless any kind of special process treatment for the whole hay is undertaken. 2. In each individual drying system, the following conclusions were drawn: a. After 8 days sun-drying on concrete floor under good days with average tempe\ulcornerrature at $256{\circ}C$ and relative humidity at 55% at 2 P.M., the moisture content of long hay was still above 25 5'~ and the leaf loss during drying caused by wind and rough handling was more than 50 ~G. b. It was possible to dry the chopped seombody by sun-drying down to about 10 % moisture content within 5 days, however, a stock of heat and discolouration phenomena were observed during the drying, which may be due to the increased deposit-density by chopping, resulting in lowering the quality of the dried product. c. Sun-drying for the crushed material by hay-conditioner was required about 4 days to reduce the moisture content to about 10 %, keeping the quality of dried product at good grade. o. The optimum deposit-depth of the chopped seombody in the batch-type dryer used was about 28cm with about 42kg/hr of drying performance rate. However, it was necessary to overturn the materials between the upper and lower layers in order to obtain a good quality of dried product. d. The drying performance rate by the tunnel-type drier was highest among those of drying systems tested, giving the rate of approximately 400kg/day. 3. On reviewing the individual drying system for seombody, it was possible to draw conclusion that the best system was tunnel drying with the crushed seombody as far as the performance rate was concerned. However, the methods gives the highest operational cost. The system for the lowest operational cost with good quality of dried product was the sun-drying with the crushed material. Accordingly, it may be recommended that the system of sun-drying for the crushed seombody may be the most feasible system presently applicable to farm-level operation.

• Asian-Australasian Journal of Animal Sciences
• /
• v.6 no.2
• /
• pp.197-203
• /
• 1993

The protection of dry matter and nitrogen from rumen degradation of dhaincha seed (Sesbania aculeate) meal was studied using nylon bag technique. The dhaincha seed meal was subjected to various heat treatments that included oven drying, autoclaving and boiling. Similar experiment was conducted with fish meal as reference for comparison. The oven-dried dhaincha meal was found to retain more dry matter and nitrogen than was found boiled or autoclaved meal. While autoclaving appeared to improve nitrogen and dry matter retention to some extent, boiling seemed to cause more loss of dry matter from nylon bag. Heat treatment caused high retention of nitrogen by fish meal. The calculated effective protein degradation was 80.4% and 83.2% for the oven dried fish meal and dhaincha seed meal whereas same values were 74.2% and 86.7% for autoclaved fish and dhaincha seed meal respectively at the outflow rate of 4.4% per hour. The in vitro study revealed higher digestibility for heat treated samples by pepsin. The dry matter, nitrogen and ash content of dhaincha seed meal were 85.93%, 5.93% and 7.31% respectively.

• Food Science of Animal Resources
• /
• v.33 no.2
• /
• pp.170-180
• /
• 2013

This study was conducted to evaluate the antioxidant activity of oven-dried ($60^{\circ}C$) tomato powder (TP) as affected by water solubility and to evaluate the effects of TP on the physico-chemical properties, and antioxidant and antimicrobial activities of emulsified pork sausages with two levels of TP (1% and 2 %). After fresh tomatoes were homogenized and dried at $60^{\circ}C$ oven, they were extracted by stirring with water. Then, the aqueous solution was filtered, and water soluble and insoluble tomato powders were obtained with freeze drying. In experiment I, total phenolic contents in oven-dried tomato powder, water soluble and insoluble powder were more than 2 g/100 g. The radical scavenging activity and iron-chelation ability of the water-insoluble extracts were higher than those of dried TP and water-soluble extracts. In experiment II, pH values and Hunter L values of pork sausages formulated with TP were reduced. However, hunter a and b values were higher than those of the control, and those effects were increased with increased levels of TP. 2-Thiobarbituric acid reactive substance values of pork sausages containing TP were lower than that of the control during refrigerated storage, regardless of the TP level. These results indicated that TP could be used as a natural color agent and antioxidant in meat products without defects.

• Food Science of Animal Resources
• /
• v.40 no.5
• /
• pp.722-733
• /
• 2020

This study was aimed to investigate the physicochemical properties, texture, and antioxidant, and antimicrobial activities of regular-fat sausages (RFSs) mixed with 0.25 and 0.5% of oven-dried and freeze-dried grape tomato powder (GTP, 150 ㎛) during storage at 4℃. RFSs were made by six treatments that included: control (CTL), REF (sausages with 0.1% ascorbic acid alone), F1GTPSs (F1) and F2GTPSs (F2) (sausages with 0.25% and 0.5% freeze-dried GTP), and O1GTPSs (O1) and O2GTPSs (O2) (sausages with 0.25% and 0.5% GTP oven-dried at 100℃). Sausages with added oven-dried grape tomato powders (OGTPs) showed decreased pH, lightness (L^⁎), total plate count (TPC), and thiobarbituric acid-reactive substances (TBARS) compared to the sausages mixed with freeze-dried GTP (FGTPSs), but also had the highest redness (a^⁎) and yellowness (b^⁎) values among the treatments. With increasing levels of GTP, the hardness and chewiness of the sausages gradually decreased and these were decreased more in the FGTPSs (F) than in the OGTPSs (O). Compared to the FGTPSs, OGTPSs had higher antioxidant and antimicrobial activities, which extend the shelf-life of meat products. Application of OGTP to RFSs resulted in higher lipid antioxidant, antimicrobial activities, improving physicochemical properties and extended the shelf-life.