• Structural Engineering and Mechanics
• /
• 제34권2호
• /
• pp.143-157
• /
• 2010

This paper presents theoretical solutions for the three-dimensional (3D) stress field in an infinite isotropic elastic plate containing a through-the-thickness circular hole subjected to far-field in-plane loads by using Kane and Mindlin's assumption. The dangerous position, where the premature fracture or failure of the plate will take place, the expressions of the tangential stress at the surface of the hole and the out-of-plane stress constraint factor are found in a concise, explicit form. Based on the present theoretical solutions, a comprehensive analysis is performed on the deviated degree of the in-plane stresses from the related plane stress solutions, stress concentration and out-of-plane constraint, and the emphasis has been placed on the effects of the plate thickness, Poisson's ratio and the far-field in-plane loads on the stress field. The analytical solution shows that the effects of the plate thickness and Poisson's ratio on the deviation of the 3D in-plane stress components is obvious and could not be ignored, although their effects on distributions of the in-plane stress components are slight, and that the effect of the far-field in-plane loads is just on the contrary of that of the above two. When only the shear stress is loaded at far field, the stress concentration factor reach its peak value about 8.9% higher than that of the plane stress solutions, and the out-of-plane stress constraint factor can reach 1 at the surface of the hole and is the biggest among all cases considered.

• 대한기계학회논문집A
• /
• 제27권9호
• /
• pp.1531-1538
• /
• 2003

This paper compiles solutions of plastic $\eta$ factors and crack tip stress triaxialites for standard and nonstandard fracture toughness testing specimens, via detailed three-dimensional (3-D) finite element (FE) analyses. Fracture toughness testing specimens include a middle cracked tension (M(T)) specimen, SE(B), single-edge cracked bar in tension (SE(T)) and C(T) specimen. The ligament-to-thickness ratio of the specimen is systematically varied. It is found that the use of the CMOD overall provides more robust experimental J estimation than that of the LLD, for all cases considered in the present work. Moreover, the J estimation based on the load-CMOD record is shown to be insensitive to the specimen thickness, and thus can be used for testing specimen with any thickness. The effects of in-plane and out-of-plane constraint on the crack tip stress triaxiality are also quantified, so that when experimental J value is estimated according to the procedure recommended in this paper, the corresponding crack tip stress triaxiality can be estimated. Moreover, it is found that the out-of-plane constraint effect is related to the in-plane constraint effect.

• Steel and Composite Structures
• /
• 제2권4호
• /
• pp.237-246
• /
• 2002

In this paper, the solution of a semi-infinite plane with one circular hole is presented. This solution is induced by repeatedly superposing the solution of an infinite plane with one circular hole and that of a semi-infinite plane without holes to cancel out the stresses arising on both boundaries. This procedure is carried out until the stresses arising on both boundaries converge. This method does not require complicated calculation procedures as does the method using stress functions defined in a bipolar coordinate system. Some numerical results are shown by graphical representations.

• 대한기계학회논문집A
• /
• 제38권12호
• /
• pp.1441-1446
• /
• 2014

본 논문에서는 휜 광폭평판의 두께와 폭, 균열길이 그리고 가공경화지수의 변화가 휜 광폭평판의 균열부 구속상태에 미치는 영향을 평가하였다. 이를 위해 5가지의 휜 광폭평판 두께, 3가지의 균열길이, 3가지의 휜 광폭평판 폭 그리고 3가지의 가공경화지수를 고려한 3차원 탄소성 유한요소해석을 수행하였다. Ramberg-Osgood 관계식을 만족하는 비선형 재료로 가정하였으며 균열부 구속상태를 정량화하기 위해서 Q-응력을 이용하였다. 3차원 유한요소해석 결과를 바탕으로 기하학적 형상 및 재료특성에 따른 휜 광폭평판의 Q-응력 변화를 평가하였다. 평가 결과 면외 구속조건에 의한 영향은 면내 구속조건과 밀접한 관계가 있었으며, 면외 구속조건이 면내 구속조건 보다 균열부 구속상태에 더 큰 영향을 미쳤다.

• Journal of Welding and Joining
• /
• 제10권1호
• /
• pp.35-42
• /
• 1992

In this study, the stress concentration phenomenon for the dissimilar joints(ceramic-metal) bonded by thermal treating using a soft-insert metal(copper) was investigated with the aid of FEM(finite element method) under the load condition of uniform tension. The analysis was carried out by the supposing that stress states are plane stress or plane strain and elastic or elastic-plastic. And the Von Mises yield criterion and the incremental theory as plastic flow were adopted in this analysis. As the summarized results obtained, the stress concentration phenomenon was severer as the soft insert metal was thicker, in plane strain than in plane stress and in elastic-plastic state than in elastic state. Furthermore, the inducing mechanism of stress concentration was well expressed by the constraint forces(Fc) generated between the soft and the hard material.

• 대한기계학회논문집A
• /
• 제28권7호
• /
• pp.1021-1028
• /
• 2004

Kim et al. suggested an experimental method to determine the Q parameter in situ from the out-of-plane displacement and the in-plane strains on the surface of side necking near the crack tip. In this paper, the procedure to evaluate the stress triaxiality near a crack tip such as the Q parameter is to be polished in the details for simplicity and accuracy. That is, Q and hydrostatic stress are determined only from the out-of-plane displacement, but not using in-plane strain, which is hard to measure. And also, the plastic modulus is determined by an alternative way. Through three-dimensional finite element analyses for a standard CT specimen with 20% side-grooves, the validities of the new procedures are examined in comparison to the old ones. The effect of location where the displacements are measured to determine the stress triaxiality is explored.

• 한국생산제조학회지
• /
• 제5권4호
• /
• pp.74-81
• /
• 1996

This paper is to estimate sizing design sensitivity of linear and nonlinear vehicle frame structure using structural ananlysis result from ANSYS. Using design sensitivity results, optimal design of plane vehicle frame structure with buckling constraint is carried out the gradient projection method. Optimal design results are compares gradient projection method resrult with SUMT result.

• 대한기계학회논문집
• /
• 제16권3호
• /
• pp.419-429
• /
• 1992

본 연구에서는 면외 변형이 가능한 평면 곡선보에 수정 형상함수를 적용하여 탈락성 및 지속성 에너지에 포함된 가성구속에 의한 수치해의 거동을 고찰함과 동시에, 가성구속에 의한 오차 발생 요인이 제거된, 면외 변형이 가능한 평면 곡선보의 선형 요소를 제안하고자 한다.

• Journal of Mechanical Science and Technology
• /
• 제14권3호
• /
• pp.272-282
• /
• 2000

Based on numerical reduced minimization theory, new anisoparametric 3-node elements for out-of-plane curved beam are developed. The elements are designed to be free from spurious constraints. In this paper, the effect of the Jacobian upon numerical solution is analyzed and predicted through reduced minimization analysis of anisoparametric 3-node elements with different Jacobian assumption. The prediction is verified by numerical tests for circular and spiral out-of-plane deformable curved beam models. This paper proposes two kinds of 3-node elements with 7-DOF; one element employs 2-point integration for all strains, and the other element uses 3-point integration with a constant Jacobian within element for calculation of shear strain.

• 대한기계학회논문집
• /
• 제17권7호
• /
• pp.1719-1730
• /
• 1993

This paper presents the theoretical natural frequencies of out-of-plane deformable ring based on the variables such as out-of-plane deflection, torsional rotation and shear rotation. Based on the same variables, a finite element eigen analysis is carried out by using the $C^0$-continuous, isoparametric element which has three nodes per element and three degrees-of-freedom at each node. Numerical experiments are peformed to find the integration scheme which produces accurate natural frequencies, natural modes and correct rigid body motion. The uniformly reduced integration and the selective reduced integration give more accurate numerical frequencies than the uniformly full integration, but the uniformly reduced integration produces incorrect rigid body motion while selective reduced integration does correct one. Therefore, the ring element based on the three variables which employes selective reduced integration is recommended to avoid spurious modes, to alleviate the error due to shear locking and to produce correct rigid body motion, simultaneously.