• Proceedings of the National Institute of Ecology of the Republic of Korea
• /
• v.3 no.1
• /
• pp.1-6
• /
• 2022

Among the 13 species of otters in the world, only one Eurasian otter (Lutra lutra) is found in South Korea. In the Korean Peninsula, otter pelts were historically valuable and expensive commodities used for international trade, and otters have long been poached as hunting animals. Recent rapid economic development in South Korea has increased habitat fragmentation and loss, creating a continuing threat to the natural environment. Otters live only in the area of rivers and streams as a family group and are territorial (linear habitat). Due to these limited conditions of otter habitat, the population size of otter is lower than that of onshore mammals. According to recent research, DNA analyses using microsatellite markers have shown that only approximately 7-21 otter individuals inhabit river systems for a length of 50-230 km. Korea's urban streams are associated with many threats that hinder otters from inhabiting them. Many areas around the urban streams are surrounded by high concrete riverbanks, and the risk of roadkill is also high. Nevertheless, ecological restoration projects in the urban rivers will contribute greatly to the stable inhabitation of otters. Detailed otter conservation strategies, such as the elimination of threat factors, improvement of habitat environment, and restoration of food resources and shelter, will provide a positive restoration effect on otter and river ecosystems as well.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.28 no.2
• /
• pp.132-143
• /
• 1992

This paper presents a method in order to calculate the vortex distribution, the streak-line and the time-line around the flat and the cambered otter board in two dimensional flow using the discrete vortex method, and to calculate C sub(L) and C sub(D) of the otter boards varied with the passage of time by the numerical simulation using the Blasu's formula. The results obtained are summarized as follows: 1. Flow pattern around the otter boards calculated by the discrete vortex method was resembled closely that of the visualized photograph. 2. C sub(L) and C sub(D) calculated by the numerical simulation was very similar to the model test. 3. The circulation direction around the otter boards and the action direction of the shearing force can be recognized from the time-line around the otter boards. 4. Flow speed in the back side of the otter boards was faster than that in the front side, and the difference of the flow speed in both side of the cambered otter boards was about 1.3 times greater than that of the flat otter boards. 5. The clockwise vortex was generated in the trailing edge, and the counter-clockwise vortex was generated the leading edge of the otter boards. And they were shown the shape of Karman's vortex varied with the passage of time.

• Fisheries and Aquatic Sciences
• /
• v.17 no.1
• /
• pp.145-153
• /
• 2014

The motion of the otter board on a trawl can affect the motion of trawl nets, and the motion of the codend can affect fish selectivity. Preliminary measurements of the tilt of bottom trawl gear were carried out to compare the tilts of the otter board and codend. The tilt of the otter board was measured by Vector and tilt at 1.5 m anterior to the end of the codend, and the middle upper panel was measured with a micro-DST-tilt logger. Tilt data such as yaw, pitch, and roll were analyzed by the fast Fourier transformation method and global wavelet and event analyses for the period or amplitude. The mean period ${\pm}$ standard deviation of the tilt in the otter board, $(5-6){\pm}2s$, was similar to the period of the codend, $(4-6){\pm}(2-3)s$, whereas the amplitude of the codend was greater than that of the otter board. The yaw and pitch periods were not significantly different between the otter board and codend, but roll was different. Furthermore, the tilt period frequencies of the otter board and codend were not significantly different. Accordingly, the tilt motion of the codend was mostly related to the tilt of the otter board.

• Spatial Information Research
• /
• v.10 no.4
• /
• pp.501-513
• /
• 2002

Eurasian otter (Lutra lutra) is one of endangered wildlife species whose population size is declining in Korea. To manage and conserve habitat for Eurasian otter, it is crucial to understand which habitat components affect otter habitat qualities. The objectives of this study were to develop a habitat suitability model of Eurasian otter in Soraksan National Park, to validate the model in Odaesan National Park. The research methods of this study were as follows. First, trace data and characters of Eurasian otter habitat were collected with Geographic Information System (GIS) data and Global Positioning System (GPS) receivers between 2000 and 2002. Second, the habitat use factors were identified as habitat characteristics of Eurasian otter and classified with habitat use and availability analyses. Third, significant factors of habitat model were extracted by Chi-square test. The last, Eurasian Otter Habitat Suitability Model (EOHSM) was employed by logistic regression method. Otter habitat use was positively associated with the reeds and shrubs areas adjacent to streams, the size of boulders, and low human disturbance in Soraksan National Park by EOHSM. This model had a classification accuracy of 74.4% at cutoff value of 0.5. Model validation showed a classification accuracy of 86.6 % at cut off value of 0.5 for otter habitat in Odaesan National Park.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.43 no.1
• /
• pp.49-61
• /
• 2007

Otter boards in the trawl are the one of essential equipments for the net mouth to be spread to the horizontal direction. Its performance should be considered in the light of the spreading force to the drag and the stability of towing in the water. Up to the present, studies of the otter boards have focused mainly on the drag and lift force, but not on the stability of otter boards movement in 3 dimensional space. In this study, the otter board is regarded as a rigid body, which has six degrees of freedom motion in three dimensional coordinate system. The forces acting on the otter boards are the underwater weight, the resistance of drag and spread forces and the tension on the warps and otter pendants. The equations of forces were derived and substituted into the governing equations of 6 degrees of freedom motion, then the second order of differential equations to the otter boards were established. For the stable numerical integration of this system, Backward Euler one of implicit methods was used. From the results of the numerical calculation, graphic simulation was carried out. The simulations were conducted for 3 types of otter boards having same area with different aspect ratio(${\lambda}=0.5,\;1.0,\;1.5$). The tested gear was mid-water trawl and the towing speed was 4k't. The length of warp was 350m and all conditions were same to each otter board. The results of this study are like this; First, the otter boards of ${\lambda}=1.0$ showed the longest spread distance, and the ${\lambda}=0.5$ showed the shorted spread distance. Second, the otter boards of ${\lambda}=1.0$ and 1.5 showed the upright at the towing speed of 4k't, but the one of ${\lambda}=0.5$ heeled outside. Third, the yawing angles of three otter boards were similar after 100 seconds with the small oscillation. Fourth, it was revealed that the net height and width are affected by the characteristics of otter boards such as the lift coefficient.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.22 no.4
• /
• pp.41-48
• /
• 1986

To investigate the midwater trawl gear available for the Korean near sea trawlers, the authors carried out a field experiment on the attitude and the opening efficiency of the otter board with the Pusan 404 (160GT, 750ps), a training ship of National Fisheries University of Pusan. The experimental trawl gear was designed to be operable by the ship and the otter board was made of single iron plate with 12% camber ratio. The special-prepared potentiometric angle detector was used for determining the attitude, and the 50 KHz fish finder for the opening between the otter boards. The results obtained can be summarized as follows: 1. The angle of attack varied by moving the towing point on the towing plate of the otter board. It showed 33 to 36 degrees when the point was set at the outmost position, 25 to 31 degrees at the middle position and 19 to 30 degrees at the inmost position, with a decreasing tendency according to the increase of towing speed in each cases. 2. The heel of the otter board always occured inwards, increasing slightly according to the increase of towing speed. 3. The tilt of the otter board always occured outwards, increasing slightly according to the move of the towing point inwards, and decreasing slightly according to the increase of towing speed. 4. The opening between otter boards showed the largest value when the towing point was set at the outmost position.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.51 no.1
• /
• pp.26-34
• /
• 2015

The angle of attack of a cambered otter board in a bottom trawl was estimated using a three-dimensional semi-analytic treatment of a towing cable (warp) system that was applied to the field experiments of a bottom trawl obtained by the Scanmar system. The equilibrium condition of the horizontal component and vertical component of forces was used to the three forces acting on the otter board in the horizontal plane. Those forces were the force on the warp at the bracket, hydrodynamic lift and drag forces on the otter board and the force on the hand rope attached just behind the otter board. Also the equilibrium of moment about the front edge of the otter board was used to find out the angle of attack of the cambered otter board. When the warp length was 120m and 180m long and the towing speed was between 1.23 and 1.90 m/s, the estimated angle of attack of the cambered otter board was ranged between $26.1^{\circ}$ and $29.6^{\circ}$, respectively, though the maximum lift force was at the angle of attack $22.6^{\circ}$. The angle of attack of the otter board was tended to increase weakly with the longer length of warp (180 m) at the same towing speed in the experiment.

• Journal of Environmental Impact Assessment
• /
• v.22 no.5
• /
• pp.525-528
• /
• 2013

River otter(Lutra lutra) are listed as endangered species and Natural monument in Korea, and this study examined the possibility of extinct of river otter in Hongchon river using with the application of Population Viability Analysis (PVA) technique. In Hongchon river areas population was estimated 9 individuals for the last 1999-2005 years and PVA analysis was done for the next 10 years using the average population of 9. Using the initial population the river otter was estimated 30% of extinct for the next 10 years. This estimation was quite low considering water pollution and construction of highways. Also PVA only used population size lacking in other life history information. Nonetheless river otter population can be in risk of extinction if the current construction of crossovers, cement bank are maintained. Long term information regarding life history needs essential.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.24 no.2
• /
• pp.78-82
• /
• 1988

Near sea trawlers of Korea sometimes catch pelagic fishes like file fish by using midwater trawl gear even though usually catch bottom fish. It is reasonable to use the specific otter board as well as specific net in bottom trawling and in midwater trawling respectively. But, the trawlers are so small ranging 100 to 120GT, 700 to 100ps that it is very complicated to use different otter board for bottom trawling and for midwater trawling. The otter board for bottom trawling. is also used for the midwater trawling without any change even though the net is changed into the specific one. Although the otter board in the midwater trawling should be lighter than that for bottom trawling, to use otter board for bottom trawling directly for the midwater trawling without any change makes the net easily touch the sea bed and also make the horizontal opening of the otter boards be limited owing to the length of warp in the southern sea of Korea, main fishing ground of midwater trawling, which is 100m or so in depth. That is why the otter board for the midwater trawling should be made lighter than that in the bottom trawling, even if temporary. The authors carried out an experiment to achieve this purpose by attaching a large styropol float on the top of the otter board. In this experiment, underwater weight of the otter board was 630kg and buoyancy of the float was 510kg. To determine the depth and horizontal opening of the otter board, two fish finder was used. A transmitter of 50KHz fish finder was set downward through the shoe plate of otter board to determine the elevation of otter board from the sea bed, and a transmitter of 200KHz fish finder was set sideways on the starboard otter board to be able to detect the distance between otter boards. The obtained results can be summarized as follows: 1. The actual towing speed in the experiment varied 1.1 to 1.8 m/sec. 2. The depth of otter board was within 41 to 25m with float on the top and 45 to 26m without float in case of the warp length 100m, whereas the depth 68-44m with float and 74-46m without float in case of the warp length 150m. This fact means that the depth with float was 9-4% shallower than that without float. 3. The horizontal opening between otter boards was within 34-41m with float and 30-38m without float in case of the warp length 100m, whereas the opening was 44-50m with float and 37-46m without float in case of the warp length 150m. This fact means the opening with float was 10% greater than that without float in case of the warp length 100m, and 15% greater in case of the warp length 150m. 4. The horizontal opening between wing tips by using the otter board with float was 1m greater than by without float in case of the warp length 100m, whereas the opening by with float was 2m greater than by without float in case of warp length 150m. From this fact, it can be estimated that the effective opening area of the net mouth by using the otter board with float could be made 10% greater than by without float in case of warp length 100m, whereas the area with float 20% greater than by without float in case of warp length 150m.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.20 no.2
• /
• pp.114-118
• /
• 1987

The authors carried out a model experiment to examine the hydrodynamic charactristics of the simple camber and the super-V otter board. The model otter boards are made of 1 mm thick iron plate. The simple camber otter board is made to have $12\%$ camber ratio and $432\;cm^2$ plane projected area, and the super-V otter board to have the same camber ratio as the former in every latitudinal section and almost the same plane projected area. The experiment had been done in a circular flow tank in the speed range of $0.1\~1.2m/sec$. As a result, it is examined that in the simple camber otter board the most effective angle of attack is about $25^{\circ}$, the shearing coefficient 1.47 and the drag coefficient 0.42, while in the super-V otter board they are about $20^{\circ}$, 1.40 and 0.40 respectively, so that the simple camber otter board performs a little better efficiency than the super-V otter board.