• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.33 no.3
• /
• pp.251-260
• /
• 2009

Hybrid locomotive UGV with actively articulated legs along with wheeled ends has high traversability to travel over rough terrain. The behavior control method was usually adapted for the controlling of the suspension configuration which determines the traversability of the UGV. In this study, we are proposing a method of configuration planning of the legs without any detail geometric data about the terrain. The terrain was estimated by the traces of each wheel and the leg configurations for the desired posture of the vehicle were set up against the constraints of the terrain. Also, an optimal leg configuration was calculated based on the quasi-static stability and power consumption, and plans for the leg behavior were made. Validity of the proposed method was checked by simulations using some off-the-shelf programs, and showed that the orientation control without geometric features of terrains and simplification of the behavior planning for obstacle negotiation were possible.

• Proceedings of the KIEE Conference
• /
• 2002.07c
• /
• pp.1397-1399
• /
• 2002

Effects of bottom electrode materials (Al, Cu, Ti, and Mo), included in film bulk acoustic resonators (FBARs), on the orientation of piezoelectric AlN thin films and the frequency response characteristic of resonators were investigated. The texture coefficient (TC) for (002) orientation, crystallite size, full width half maximum (FWHM), and surface roughness of deposited AlN films were measured for the various bottom electrodes. The return tosses estimated from the frequency responses of fabricated resonators were also compared. Experimental results showed that the difference of lattice constant and thermal expansion coefficient between the bottom electrode and the AlN film were the most important factors for achieving a high performance resonator.

• Steel and Composite Structures
• /
• v.31 no.4
• /
• pp.387-396
• /
• 2019

This paper deals with the effect of ply orientation and control gain on tip transverse displacement of functionally graded beam layer for both active constrained layer damping (ACLD) and passive constrained layer damping (PCLD) system. The functionally graded beam is taken as host beam with a bonded viscoelastic layer in ACLD beam system. Piezoelectric fiber reinforced composite (PFRC) laminate is a constraining layer which acts as actuator through the velocity feedback control system. A finite element model has been developed to study actuation of the smart beam system. Fractional order derivative constitutive model is used for the viscoelastic constitutive equation. The control voltage required for ACLD treatment for various symmetric ply stacking sequences is highest in case of longitudinal orientation of fibers of PFRC laminate over other ply stacking sequences. Performance of symmetric and anti-symmetric ply laminates on damping characteristics has been investigated for smart beam system using time and frequency response plots. Symmetric and anti-symmetric ply laminates significantly reduce the amplitude of the vibration over the longitudinal orientation of fibers of PFRC laminate. The analysis reveals that the PFRC laminate can be used effectively for developing very light weight smart structures.

• Journal of international Conference on Electrical Machines and Systems
• /
• v.2 no.4
• /
• pp.466-472
• /
• 2013

The paper presents a novel DC grid connection topology and control strategy for doubly-fed induction generator (DFIG) based wind power generation system. In order to achieve the wind power conversion, the stator side converter and the rotor side converter is used to implement the DFIG control based on the indirect air-gap flux orientation, and a DC/DC converter is used for the DFIG system to DC grid connection. The maximum power point tracking and DC voltage droop control can also be implemented for the proposed DFIG system. Finally, a 4-terminal DFIG-based multi-terminal DC grid system is developed by Matlab to validate the availability of the proposed system and control strategy.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.302-305
• /
• 2003

In this paper, dynamic behaviors of a small-sized flying robot with 4 rotors propelled by DC motor are discussed, and a control scheme based on the dynamic model to make stable flying motions, i.e., hovering, take-off, cruising behavior, etc. is proposed. The experimental results via some flying tests show good performances for practical use. The flying robot with 6DOF is controlled only 4 DOF, and the rest of two DOF are remained under the dynamic constraints. How to give the stability of all positions and orientations and to make the omni-directional motions in spite of such restrictions is analyzed. The proposed control scheme composes of two stages. First, PD control inputs for the trust-force and orientation are calculated, next the control inputs are distributed to each rotor by using a sort of Jacobian matrix. To design and control of a low cost - small sized flying robot, vibrated gyro sensor, cheap accelerometer, IR, and ultra sonic sensors are selected.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.5B no.4
• /
• pp.358-365
• /
• 2005

In induction machine drive without a speed sensor, the estimation of the motor flux and speed often becomes deteriorated at low speeds with low back EMF. Our analysis shows that, in addition to the state resistance variation, the estimated value of field orientation angle is often corrupted by accumulative errors from the integration of voltage variables at motor terminals that have low signal/noise ratio at low frequencies. A repetitive loop path of integration in the feedback can amplify this type of error, thus speeding up the degradation process. The control system runs into information starvation due to the loss of correct field orientation. The machine's spiral vectors are controlled only in a reduced dimension in this situation. A novel control scheme is developed to improve the control performance of motor's current, torque and speed at low frequencies. The scheme gains a full-dimensional vector control and is less sensitive to the combined effect of the error sources at the low frequencies. Experimental tests demonstrate promising performances are achievable even below 0.5 Hz.

• Journal of Korean society of Dental Hygiene
• /
• v.12 no.1
• /
• pp.167-178
• /
• 2012

Objectives : The purpose of this research is to examine the effects of the goal achievement orientation of the students in dental-hygiene practice classes on their self-efficacy and on their adaptation to and satisfaction with their major. Methods : A survey was conducted among the dental-hygiene students in schools located in the Daegu region on October 24-31, 2011. A total of 212 accomplished questionnaires were gathered as sources of final analytical data. Statistical analysis was conducted on the collected data, using the SPSS 19.0 program. Results : 1. The students who had good personal relationships(p=.000) and who chose their major and school based on their aptitude(p=.029) were found to have a higher degree of satisfaction than those who did not have good personal relationships and who did not choose their major and school based on their aptitude. 2. Self-confidence(p=.004), self-control efficacy(p=.000), mastery approach(p=.000), and performance approach(p=.003) were found to have positive correlations with major adaptation while task difficulty preference(p=.000) was found to have a negative correlation with the same. 3. Self-confidence(p=.004), self-control efficacy(p=.000), mastery approach(p=.000), and performance approach(p=.045) were also found to have a positive correlation with major satisfaction while task difficulty preference(p=.000) was found to have a negative correlation with the same. 4. Mastery approach(p=.000) in goal achievement orientation was found to have a positive effect on self-efficacy while mastery avoidance(p=.001) was found to have a negative effect on the same. Mastery avoidance showed the greatest effect on self-confidence(p=.000) while mastery approach showed the greatest effect on self-control efficacy(p=.000) and task difficulty preference(p=.000). 5. In goal achievement orientation, mastery approach(p=.000) was found to have a positive effect on major adaptation while mastery avoidance was found to have a negative effect on the same. Meanwhile, with regard to self-efficacy, self-control efficacy(p=.037) and task difficulty preference(p=.008) were found to have positive effects on major adaptation. 6. In the case of major satisfaction, mastery approach(p=.000) in goal achievement orientation was found to have a positive effect on it, and in self-efficacy, self-control efficacy(p=.038) and task difficulty preference(p=.002) were found to have positive effects on it. Conclusions : Accordingly, to raise the level of the dental-hygiene students' adaptation to and satisfaction with their major, the students should be given appropriate tasks so that they can raise their mastery goal, and they should be encouraged to raise their approach goal rather than their avoidance goal. In addition, the students should be provided assistance in setting self-expectations and in developing confidence in their capabilities.

• Journal of Institute of Control, Robotics and Systems
• /
• v.8 no.9
• /
• pp.812-817
• /
• 2002

This paper presents a development of high accuracy aligner and describes a method to find the orientation of a substantially circular disk shaped wafer with at least one flat region on an edge thereof. In the developed system, the wafer is spun one 360 degree turn on a chuck and the edge position is measured by a linear array to obtain a set of data points at various wafer orientation. The rotation axis may differ from wafer center by an unknown eccentricity. The flat angle is found by fitting a cosine curve to the actual data to obtain a deviation. The maximum deviation is then corrected for errors due to a finite number of data points and wafer eccentricity by calculating an adjustment angle from data points on the wafer fiat. After determining the flat angle the wafer is spun to the desired orientation. The wafer eccentricity can be calculated from four of the data points located away from the flat edge region. and the wafer is then centered.

• Journal of Institute of Control, Robotics and Systems
• /
• v.15 no.4
• /
• pp.379-384
• /
• 2009

A human gaze detection and tracing method is importantly required for HMI(Human-Machine-Interface) like a Human-Serving robot. This paper proposed a novel three-dimension (3D) human gaze estimation method by using a face recognition, an orientation estimation and SVMs (Support Vector Machines). 2,400 images with the pan orientation range of $-90^{\circ}{\sim}90^{\circ}$ and tilt range of $-40^{\circ}{\sim}70^{\circ}$ with intervals unit of $10^{\circ}$ were used. A stereo camera was used to obtain the global coordinate of the center point between eyes and Gabor filter banks of horizontal and vertical orientation with 4 scales were used to extract the facial features. The experiment result shows that the error rate of proposed method is much improved than Liddell's.

• Journal of Institute of Control, Robotics and Systems
• /
• v.4 no.3
• /
• pp.334-341
• /
• 1998

This paper proposes an algorithm to obtain the time-to-contact between an observer and a target and surface orientation of the target. These two physical elements are computed from the image deformation of a known shape, which is extracted by supervised classification of detected line segments based on MAP and Mahalanobis distance. The proposed algorithm was applied to the natural outdoor traffic scene and would contribute to the development for a collision avoidance system.