• Proceedings of the Korean Environmental Sciences Society Conference
• /
• 2003.11a
• /
• pp.216-225
• /
• 2003

Fine particles with aerodynamic diameter less than 2.5 ${\mu}m$ (PM2.5) were collected from three sites in Beijing during April, August, and November 2000 and January 2001. After chemical components in samples are analyzed, a chemical mass balance (CMB) receptor model using PARs as tracers is applied to quantify the source contributions to PM2.5 in Beijing. The results show that the major sources are coal combustion, fugitive dust, vehicle exhaust, secondary sulfate and nitrate, and organic matter while biomass burning and construction dust contribute only a small fraction. In addition, source inventory in Beijing is used to determine the primary source contributions. The two methods result in comparable results. Source apportionment at three sampling sites presents similar contributions to PM2.5 although the sites are far away from each other. However, distinct seasonal pattern is presented for the source contributions from coal combustion, fugitive dust, biomass burning, secondary sulfate and nitrate.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.6
• /
• pp.550-553
• /
• 2005

[ $Pb(Zr_{0.2}Ti_{0.8})O_3$ ] powders, prepared by the sol-gel method, were mixed with an organic vehicle and the PZT thick films were fabricated by the screen-printing techniques on Pt/alumina substrates. The structural and dielectric properties were examined as a function of sintering temperature. The particle size distribution of the powder is bimodal with the mean particle size of about $1.2\;{\mu}m$. The average grain size of the PZT thick films sintered above $1000^{\circ}C$ was about $3.1\;{\mu}m$ and the thickness of the specimens was approximately $41\;{\mu}m$. The relative dielectric constant and dielectric loss of the thick films sintered at $1050^{\circ}C$ were 337 and $1.24\%$, respectively.

• Journal of the KSME
• /
• v.35 no.10
• /
• pp.924-932
• /
• 1995

국제 환경규제가 강화되어짐에 따라 초저공해 자동차인 ULEV 및 무공해 자동차인 ZEV의 개 발을 필수적이다. 캘리포니아주법규에 따르면 Maker의 NMOG(non meth-ane organic gas) 평 균치를 만족한다 하더라도 ZEV의 판매는 의무화되어 있다. 1989-1993 MY 기간중 연평균 판매 대수가 35,000대 이상인 Mater는 1998년 2% 적용대상이 되며, 2003년부터는 연간 3,000대 이상 판매되는 모든 Maker에 ZEV 10%가 적용된다. 이와 관련 2003년 이후 하이브리드 전기자동차 및 전기자동차의 개발은 나머지 75%(ULEV를 포함할 경우 25%)의 IC엔진이 탑재된 자동차를 판매하기 위해서 이루어지지 않으면 안되게 되어 있다. 하이브리드 자동차는 전기자동차와는 달리 주행거리에 제한을 받지 않으며, 엔진의 효율이 가장 좋은 RPM에서 발전기를 회전시킴으 로써 생성된 에너지를 배터리에 충전, 도심지에서 전기자동차 모드(mode)로 주행하기 때문에 대도시의 대기오염을 줄일 수 있고, 소음이 극히 적기 때문에 미래의 도시형 자동차로서 각광 받을 수 있는 자동차로 생각된다.

• Bulletin of the Korean Space Science Society
• /
• 2004.10b
• /
• pp.262-265
• /
• 2004

As a cryogen, LOx is a light blue, odorless, transparent liquid. Also it is not shock sensitive and does not decompose. However, it is a strong oxidizer and will vigorously support combustion. Therefore all harmful contaminants (such as grease, oil, fingerprint and organic materials) that could cause malfunctions, fires, or explosions in a oxygen environments must be completely removed prior to the introduction of oxygen. Especially, grease ingredient located inside of the LOx supply line, pipe and PHS (Pneumo-Hydraulic System) part can make drastic chemical reaction with oxygen. Therefore, to protect rapid reaction such as explosion, grease ingredient must be surely eliminated by a regular and irregular degreasing. Study on the availability, effectiveness and selection of degreasing detergents and method is described in this paper, and it will be useful for the construction and management of IPP test facility.

• Transactions on Electrical and Electronic Materials
• /
• v.6 no.2
• /
• pp.35-38
• /
• 2005

Pb(Zr$_{0.8}$Ti$_{0.2}$)O$_{3}$ powders, prepared by the sol-gel method, were mixed with an organic vehicle and the PZT thick films were fabricated by the screen-printing techniques on Pt/Ah03 substrates. The structural properties were examined as a function of sintering temperature. The particle size distribution of the PZT powder derived from the sol-gel process is uniform with the mean particle size of about 2.6 m. As a result of the DTA, the formation of the polycrystalline perovskite phase was observed at around $890^{circ}$CC. In the X-ray diffraction analysis, all PZT thick films showed a perovskite polycrystalline structure without a pyrochlore phase. The perovskite crystallization temperature of PZT thick films was about $890^{circ}$C. The average thickness of the PZT thick films was approximately 80-90 m.

• Proceedings of the KIEE Conference
• /
• 2005.07c
• /
• pp.1915-1917
• /
• 2005

PZT(40/60) and PZT(60/40) powders, prepared by the sol-gel method, were mixed with an organic vehicle and the PZT(40/60)/PZT(60/40) heterolayered thick films were fabricated by the screen-printing method on $Pt/Al_2O_3$ substrates. The structural properties such as DTA, X-ray diffraction and microstructure, were examined as a function of the applied pressure. In the DTA analysis, the formation of the polycrystalline perovskite phase was observed at around $880^{\circ}C$. The average thickness of the PZT heterolayered thick films which were coated five times was approximately $95-100{\mu}m$.

• Proceedings of the KIEE Conference
• /
• 2005.07c
• /
• pp.1918-1920
• /
• 2005

PZT(20/80) and PZT(80/20) powders, prepared by the sol-gel method, were mixed with an organic vehicle and the PZT(20/80)/PZT(80/20) heterolayered thick films were fabricated by the screen-printing method on $Pt/Al_2O_3$ substrates. The structural properties such as DTA, X-ray diffraction and microstructure, were examined as a function of the sintering temperature. In the DTA analysis, the formation of the polycrystalline perovskite phase was observed at around $880^{\circ}C$. The average thickness of the PZT heterolayered thick films was approximately $80-90{\mu}m.$

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.246-247
• /
• 2007

(Ba,Sr,Ca)$TiO_3$ powders, which were prepared by sol-gel method using a solution of Ba-acetate, Sr-acetate and Ca-acetate and Ti iso-propoxide, were mixed with organic vehicle and the BSCT thick films were fabricated by the screen-printing techniques on high purity alumina substrates. The structural and dielectric properties were investigated for various $Dy_2O_3$ doping contents. As a result of thermal analysis, the exothermic peak was observed at around $670^{\circ}C$ due to the formation of the polycrystalline perovskite phase. All BSCT thick films, sintered at $1420^{\circ}C$ for 2h, showed the typical XRD patterns of perovskite polycrystalline structure and no pyrochlore phase was observed. The average grain size of the specimens decreased with.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.313-314
• /
• 2005

$PbTiO_3$ and PZT(52/48) powders, prepared by the sol-gel method, were mixed with an organic vehicle and the PT/PZT(52/40) heterolayered thick films were fabricated by the screen-printing method on Pt/$Al_2O_3$ substrates. The structural properties such as DTA, X-ray diffraction and microstructure, were examined as a amount of the PbO-$PbF_2$ flux. In the X-ray diffraction analysis, PZT(52/48) thick films showed a perovskite polycrystalline structure without a pyrochlore phase.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.359-360
• /
• 2005

PZT(20/80) and PZT(80/20) powders, prepared by the sol-gel method, were mixed with an organic vehicle and the PZT(20/80)/PZT(80/20) heterolayered thick films were fabricated by the screen-printing method on Pt/$Al_2O_3$ substrates. The structural properties such as DTA, X-ray diffraction and microstructure, were examined as a amount of the excess PbO. In the DTA analysis, the formation of the polycrystalline perovskite phase was observed at around $880^{\circ}C$. The average thickness of the PZT heterolayered thick films was approximately $80{\mu}m$.