• Aerospace Engineering and Technology
• /
• v.11 no.2
• /
• pp.19-25
• /
• 2012

GEO-KOMPSAT2 shall provide higher quality of image than the COMS and uses star tracker instead of earth sensor, which requires precise onboard orbit information. This requires precise on-ground orbit determination. For COMS, orbit determination is performed using the ranging data obtained from tracking system located in DAEJON. For accurate orbit determination of GEO-KOMPSAT2, KARI is building a secondary tracking station in CHUUK Islands. In this paper, the achievable accuracy of table based onboard orbit parameter generator which interpolates orbit data obtained from on-ground orbit determination using tracking data collected from two ground stations. Two types of approaches have been applied; covariance analysis and numerical analysis. By combining two analysis results, total orbit error has been estimated.

• Aerospace Engineering and Technology
• /
• v.13 no.2
• /
• pp.7-17
• /
• 2014

This technical paper deals with development of on-board orbit generation algorithm for GEO Satellite. This paper presents the research analysis results performed in order to improve the accuracy of the existing algorithm used for generating real-time orbit information for GEO satellite. The error impact on orbit accuracy due to the orbit error sources were analyzed with the algorithm suggested by this research. As a result of the analyses, it is found that the initial orbit should be determined with an accuracy of less than 50 m and the reference position angle error for the ground station and the satellite should be maintained within ${\pm}0.0025deg$ in order to meet the orbit accuracy specification. The development of on-board flight software based on the new algorithm was accomplished and the performance verification is ongoing by using a software based performance verification tool.

• Aerospace Engineering and Technology
• /
• v.8 no.2
• /
• pp.61-67
• /
• 2009

This paper proposes an on-board orbit data generation algorithm for geostationary satellites. The concept of the proposed algorithm is as follows. From the ground, the position and velocity deviations with respect to the assumed reference orbit are computed for 48 hours of time duration in 30 minutes interval, and the generated data are up-loaded to the satellite to be stored. From the table, three nearest data sets are selected to compute position and velocity deviation for asked epoch time by applying $2^{nd}$ order polynomial interpolation. The computed position and velocity deviation data are added to reference orbit to recover absolute orbit information. Here, the reference orbit is selected to be ideal geostationary orbit with a zero inclination and zero eccentricity. Thanks to very low computational burden, this algorithm allows us to generate orbit data at 1Hz or even higher. In order to support 48 hours autonomy, maximum 3K byte memory is required as orbit data storage. It is estimated that this additional memory requirement is acceptable for geostationary satellite application.

• Journal of Space Technology and Applications
• /
• v.1 no.3
• /
• pp.302-318
• /
• 2021

A basic study was conducted on how to determine the launch timing of a space probe targeting an Earth-approaching asteroid. In the future, when a probe mission targeting an asteroid approaching Earth's orbit is conducted in Korea, in order to determine the launch time, an appropriate solution should be obtained by applying the Global Optimization technique. For this, accurate current orbit information of each asteroid must be obtained first, and prior scenarios such as Earth's orbit information, main engine performance information of the probe and launch vehicle, the number of gravity-assisted maneuvers, and maximum flight time limit should be discussed. Also, the criteria for optimization should be determined first. In this paper, based on these prerequisites and information, a method for finding the launch time of an asteroid probe was studied using the open source software such as PyKEP and Evolutionary Mission Trajectory Generator (EMTG) which are the programs for interplanetary trajectory generation purpose.

• Journal of Astronomy and Space Sciences
• /
• v.37 no.3
• /
• pp.199-208
• /
• 2020

This paper presents a kinematic ephemeris generator for Korea Pathfinder Lunar Orbiter (KPLO) and its performance test results. The kinematic ephemeris generator consists of a ground ephemeris compressor and an onboard ephemeris calculator. The ground ephemeris compressor has to compress desired orbit propagation data by using an interpolation method in a ground system. The onboard ephemeris calculator can generate spacecraft ephemeris and the Sun/Moon ephemeris in onboard computer of the KPLO. Among many interpolation methods, polynomial interpolation with uniform node, Chebyshev interpolation, Hermite interpolation are tested for their performances. As a result of the test, it is shown that all the methods have some cases that meet requirements but there are some performance differences. It is also confirmed that, the Chebyshev interpolation shows better performance than other methods for spacecraft ephemeris generation, and the polynomial interpolation with uniform nodes yields good performance for the Sun/Moon ephemeris generation. Based on these results, a Kinematic ephemeris generator is developed for the KPLO mission. Then, the developed ephemeris generator can find an approximating function using interpolation method considering the size and accuracy of the data to be transmitted.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.22 no.2
• /
• pp.125-130
• /
• 2018

The technology development of a high performance upper stage engine for a GEO(GEostationary Orbit) KSLV(Korea Space Launch Vehicle) is undergoing in Korea Aerospace Research Institute. KSLV is composed of an open cycle engine with gas generator, which is for a low orbit launch vehicle. However the future GEO launch vehicle requires a high performance upper stage engine with a high specific impulse. The staged combustion cycle engine is necessary for this mission. In this paper, current progress and future plan for staged combustion cycle engine development is described.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.11
• /
• pp.1148-1156
• /
• 2009

ETRI has developed GNSS digitized IF signal generator for providing test and evaluation environment for various software level application and navigation algorithm in Global Navigation Satellite System(GNSS). GNSS digitized IF signal generator provides two main capabilities, GPS and Galileo raw data generation and digitized IF signal generation. GNSS digitized IF signal generator consists of five main modules which are GNSS Satellite Orbit Simulation Module, Navigation Message Generation Module, Error Generation Module, GNSS IF Signal Generation Module, and Message & Signal Steering Module. We verified the signal generated by the GNSS signal generation algorithm using software receiver for generation of signal brother to real GNSS signal.

• Journal of Advanced Navigation Technology
• /
• v.22 no.6
• /
• pp.514-521
• /
• 2018

COSPAS-SARSAT 406 MHz emergency beacons include ELTs for aviation, EPIRBs for maritime, and PLBs for individuals in distress. They are used to sending messages encoded on 406 MHzdistress frequency and sending alertsfor search and rescue in distress. C/S T.001 and T.018 are COSPAS-SARSAT technical documents. They include basic technical information needed for developing beacons, howmessages are constructed, and test methods for type approval. COSPAS-SARSAT systems that use existing low earth orbit (LEO) and geostationary earth orbit (GEO) satellites do not have a return link service (RLS). So, the survivors could not confirm whether the distress signal was sending or not. However, a new medium earth orbit (MEO)satellite system has been added to thissystem, allowing confirmation through the RLS function. This paper analyzed C/S T.001 and T.018 needed to develop navigation structuresthat incorporated improved PLB of 406 MHz, a homing signal generator of 121.5 MHz, and a VHF AM transmitter for aviation of 243 MHz.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.1
• /
• pp.139-146
• /
• 2002

This paper describes the devlopment and implementation for the KOMPSAT-1 scheduling & automatic command plan generator(KSCG). Some problems in mission planning and command planning had occurred using the mission & command planning s/w in MAPS(Missin Analysis and Planning Subsystem) during the LEOP(Launch & Early Orbit Phase) & early normal mission phase due to lots of manual input process and non-automatic process. Therefore, the more mission operations for KOMPSAT-1. In order to prevent the development of new one(KSCG) which should reduce the manual process and generate automatically the command plan has been needed. As a result, the mission operations of KOMPSAT-1 has greatly became stable and more effient.

• Journal of Satellite, Information and Communications
• /
• v.12 no.4
• /
• pp.72-77
• /
• 2017

The Satellite Based Augmentation System (SBAS) broadcasts to users integrity and correction information for Global Navigation Satellite System (GNSS) such as GPS and GLONASS using geostationary orbit (GEO) satellites. In accordance with the recommendation of the International Civilian Aeronautical Organization (ICAO) to introduce SBAS until 2025, a Korean SBAS system development / construction project is underway with the Ministry of Land, Transport and Maritime Affairs. Korea Augmentation Satellite System (KASS) is a high precision GPS correction system which is composed of KASS Reference Station (KRS), KASS Processing Station (KPS), KASS Uplink Station (KUS), KASS Control Station (KCS) and GEO satellites. In this paper, we provided the conceptual design of the KASS uplink station, which is composed of the Signal Generator Section (SGS) and the Radio-Frequency Section (RFS), and interface between the KASS ground sector and the GEO satellite.