• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2001년도 봄 학술발표회 논문집
• /
• pp.551-558
• /
• 2001

The horizontal drain method is one of methods improving reclamation ground. This method reduces consolidation time by using drained installed horizontally, and negative pressure is applied on end of these drains by vacuum pump. But, effective negative pressure still wasn't evaluated in applying this method to reclamation ground. To estimate optimum negative pressure, soil box test that make a model the in-situ by installing horizontal drains in the center is performed pressing different vacuum pressure In the laboratory, and the variations in settlement and volume of drained water through the drains during consolidation process were measured. Also, water content with distance from drain and with depth is measured after the test.

• 한국수소및신에너지학회논문집
• /
• 제31권5호
• /
• pp.411-418
• /
• 2020

A reformer is a device for producing hydrogen used in fuel cells. Among them, methanol steam reformer uses methanol as fuel, which is present as a liquid at room temperature. It has the advantage of low operating temperature, high energy density, and high hydrogen production. The purpose of this study is to improve the internal flow of the pressure vessel when a bundle of methanol steam reformer in the pressure vessel goes out to a single outlet. An analysis of equilibrium reaction to methanol steam reforming reaction was conducted using Aspen HYSYS^® (Aspen Technology Inc., Bedford, USA), and based on the results, computational analysis was conducted using ANSYS Fluent^® (ANSYS, Inc., Canonsburg, USA). For comparison of the results, the height of the pressure vessel, outlet diameter, and fillet was set as variables, and the optimum geometry was selected by comparing the effects of gravity and the amount of negative pressure.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 1999년도 학술대회논문집-국제 전기방전 및 플라즈마 심포지엄 Proceedings of 1999 KIIEE Annual Conference-International Symposium of Electrical Discharge and Plasma
• /
• pp.40-45
• /
• 1999

The effect of the addition of helium, neon, argon and xenon on the production of negative hydrogen ions has been studied in a magnetically confined dc filament discharge. The addition of helium and neon produced effects similar to an equivalent increase in hydrogen pressure. However, the addition of argon and low fractions of xenon produced significant increases in the negative ion density for hydrogen at pressures around 1 mTorr. The addition of argon and xenon, by increasing electron density and decreasing electron temperature, achieved conditions closer to optimum for negative ion production. The largest enhancement of negative hydrogen ion density occurred with the addition of argon; it is suggested that this is due to a resonant energy exchange between excited argon atoms and hydrogen molecules.

• 대한인간공학회지
• /
• 제31권3호
• /
• pp.455-461
• /
• 2012

The aim of this study was to investigate the appropriate elasticity of the textile material used for making women's girdle. Background: The elastic textiles have been used for making girdle. The hard type girdle gave high pressure on the body to make slim look. However, excessively high garment pressure caused negative effect to human bodies. This study studied the material giving proper garment pressure in girdle. Method: In this study five experimental girdles were made fabrics with various elasticities. The change of garment pressures and body girths were measured after subjects wearing the experimental girdles. The garment pressure was measured at 10 points. Body girths measured at abdomen, hip, and thigh. Results: The garment pressure of the commercial girdle was high at side of waistband, side femur and back gluteal fold. The experimental girdles made with high elasticity material definitely lowered garment pressure at those points. After wearing experimental girdle their abdomen and hip girths measurements were decreased. But, thigh girth was not reduced. Conclusion: The girdle made with excellent elasticity materials reduced garment pressure significantly and it made body slim as much as the commercial girdle except the thighs. Application: This study provides guideline for the developing girdle that applying optimum range of garment pressure with body slim effect.

• 한국농공학회지
• /
• 제18권4호
• /
• pp.4251-4258
• /
• 1976

In the construction of earth dam, embankment and highway by filling, a compaction contributes to increasing the density of soil by applying pressure. The effect of compaction depends on various factors such as soil type, moisture content, gradation, consistency, and compaction energy. In this study, the correlations amone maximum dry density, moisture content, dry density, and moisture content are analyzed. Some results obtained in this study are summarizep as follows. 1. The maximum dry density sinoreases with increased of optimum moisture content and the correlations of them can be represented by; ${\gamma}$dmx=a-b(W0) 2. Maximum dry density and liquid limit show negative linear correlation and can be represented by; ${\gamma}$dmx=a-b(LL). 3. Optimum moisture content and liquid limit, plastic limit show positive linear correlation and can be represented by the following equation, W0=a+b(LL) W0=a+b(PL). 4. Liquid limit and plastic limit show positive linear correlation, and can be represented by the following equation, LL=a+b(PL).

• 한국재료학회지
• /
• 제22권6호
• /
• pp.309-315
• /
• 2012

Metal foam has many excellent properties, such as light weight, incombustibility, good thermal insulation, sound absorption, energy absorption, and environmental friendliness. It has two types of macrostructure, a closed-cell foam with sealed pores and an open-cell foam with open pores. The open-cell foam has a complex macrostructure consisting of an interconnected network. It can be exploited as a degradable biomaterial and a heat exchanger material. In this paper, open cell Mg alloy foams have been produced by infiltrating molten Mg alloy into porous pre-forms, where granules facilitate porous material. The granules have suitable strength and excellent thermal stability. They are also inexpensive and easily move out from open-cell foamed Mg-Al alloy materials. When the melt casting process used an inert gas, the molten magnesium igniting is resolved easily. The effects of the preheating temperature of the filler particle mould, negative pressure, and granule size on the fluidity of the open cell Mg alloy foam were investigated. With the increased infiltration pressure, preheat temperature and granule sizes during casting process, the molten AZ31 alloy was high fluidity. The optimum casting temperature, preheating temperature of the filler particle mould, and negative pressure were $750^{\circ}C$, $400-500^{\circ}C$, and 5000-6000 Pa, respectively, At these conditions the AZ31 alloy had good fluidity and castability with the longest infiltration length, fewer defects, and a uniform pore structure.

• 한국해안해양공학회지
• /
• 제15권1호
• /
• pp.1-10
• /
• 2003

본 연구에서는 수평배수공법에 있어서 부압과 배수재 배치간격에 대한 영향을 일련의 실내실험을 통해 살펴보았다. 중형토조실험를 이용한 적정 부압 산정에 관한 실험결과 초기에 낮은 부압을 가하고 단계적으로 높은 부압을 가하는 것이 바람직하고, 높은 부압을 가하는 경우에 일어날 수 있는 배수재의 위치 변화를 작게 하며, 배수재로부터 거리에 따라 함수비를 균등하게 감소시킴으로서 함수비 저감 효과가 큰 것으로 나타났다. 그리고. 신사전 등(1988씰 제안식을 이용하여 배수재의 평균 타설간격을 산정하여 Barron(1948)의 이론식을 이용한 계산 값과 신사전 제 침하량 측정으로부터 구한 시간 경과에 따른 압밀도를 비교한 결과 실측 압밀곡선은 신사전 등(19880의 평균타설간격(dm)을 적용한 실측 압밀곡선과 거의 유사한 경향을 보였다. 따라서, 현장에서 수평배수재를 설치한 준설지반 의 배수재 배치간격과 압밀속도를 계산함에 있어서 신사전등과 Barron의 이론식 적용이 가능할 것으로 판단된다.

• Journal of Dairy Science and Biotechnology
• /
• 제41권1호
• /
• pp.1-8
• /
• 2023

Response surface methodology (RSM) is a statistical approach widely used in food processing to optimize the formulation, processing conditions, and quality of food products. The homogenization process is achieved by subjecting milk to high pressure, which breaks down fat globules and disperses fat more evenly throughout milk. This study focuses on an application of RSM including the logit transformation to predict the efficiency of milk homogenization, which can be maximized by minimizing the relative difference in fat percentage between the top part and the remainder of milk. To avoid a negative predicted value of the minimum of this proportion, the logit transformation is used to turn the proportion into the logit, whose possible values are real numbers. Then, the logit values are modeled and optimized. Subsequently, the logistic transformation is used to turn the predicted logit into the predicted proportion. From our model, the optimum condition for the maximized efficiency of milk homogenization was predicted as the combination of a homogenizer pressure of 30 MPa, a storage temperature of 10℃, and a storage period of 10 days. Additionally, with a combination of a homogenizer pressure of 30 MPa, a storage temperature of 10℃, and a storage period of 50 days, the level of milk homogenization was predicted to be acceptable, even with the problem of extrapolation taken into account.

• 한국수자원학회논문집
• /
• 제33권3호
• /
• pp.289-298
• /
• 2000

본 연구에서는 대구광역시에 위치하고 있는 서변 펌프가압장에서 발생되는 수격압을 최소화하기 위해 사용되는 감압밸브와 공기밸브의 최적 위치결정과 감압밸브의 최적 열림정도를 도모하였다. 가압장에서 발생하는 펌프의 급정지에 기인한 수격현상은 특성선방법을 이용하여 모의를 하였다. 최적화 방법은 강력한 탐색능력을 가지고 있으며 특히 비선형 문제를 해결하는데 탁월한 성능을 가지고 있는 유전자 알고리즘을 이용하여 실시하였다. 유전자 알고리즘의 계산결과는 감압밸브의 열림시간을 적게 할수록 최고 압력수두의 완화에 효과적이고, 열림시간을 크게 할수록 최대부압의 완화에 효과적임을 알 수 있었다. 본 연구는 특성선방법을 기반으로 하는 관망부속물들의 해석이 유전자 알고리즘과 결합되어 관로내 관로부속물의 최적설계에 도움을 줄 수 있음을 보여준다.

• 한국자동차공학회논문집
• /
• 제5권6호
• /
• pp.175-182
• /
• 1997

The purpose of this study is to investigate the effects of intake manifold shapes to improve the engine performance in a 3-cylinder LPG engine with a closed loop fuel supply system. To know the flow resistance of intake manifolds with shape, the intake negative pressure of each runner in intake manifolds were measured by using the digital pressure meter at each driving condition. And, the engine torque and power have been measured with an engine dynamometer while adjusting the optimal fuel consumption ratio with a solenoid driver. As 속 results form this experiment, the torque characteris- tics were more improved with the plenum chamber(B type intake manifold) than with the banana type(A type intake manifold). The torque characteristics were improved at mid-engine speed(rpm) range as the inner diameter of the intake manifold became smaller. And also the optimum volume among the examined plenum chamber volume was 0.74 times(590cc) the displacement of the test engine.